Has 7 outputs for connecting loads and 12 inputs for connecting
various sensors/buttons.


  • 7 universal outputs support:
    • Lights
    • NC/NO heating valves
    • Blinds
    • 1 or 2-pole gates
    • 1 or 2-pole valves
    • NC/NO locks
    • Fan coil units
  • 12 Discreet inputs that support:
    • Buttons
    • Switches
    • Reed switches
    • Leak sensors
    • Motion detectors
  • 4 digital inputs for up to 8 temperature sensors


Example of connection.

Module parameters

Parameter name Value
Outputs channels qty 7
Discrete input channels qty 12
Digital input channels qty 4
Input voltage 0-250 V
Current type AC/DC
Max load per channel 8A
Max load per group 20A
Power supply 11.5 … 27.5 V DC from CAN
Max current(24V) 140 mA
BUS type CAN
Equipment installation type DIN rail (EN 60715)
Case material ABS
Protection IP40
Temperature range -10 … +50 °C
Size 6U, 105x110x58 mm
Weight 255 g


Indication of module operation.

Indicator Status Description
Power Power
Power not available
Activity Transferring data
No data transferring
Error No errors


The device blinks once every two seconds. The data has not been transferred via the CAN bus for at least 5 minutes.

Module installation and connection procedure

  1. Connect the outputs.
  2. Connect the inputs.
  3. Connect the Can connector.
  4. Configure the module using LT setup.
  5. Apply power to the load
  6. Check all equipment for proper operation.

Module shut-off and deinstallation procedure

  1. Disconnect the power from the load
  2. Disconnect the CAN connector.
  3. Disconnect the inputs.
  4. Disconnect the outputs.


HW Settings

Name Type, range SUBID Default Description
runtime integer 0-100 1-7 15 Runtime is the open/close time in seconds, is used for jalousie(2 pole), gate(2 pole), valve(2 pole); Example: rumtime=20
hold integer 0-10000 1-7 500 hold is the bridging time in miliseconds, is used for gate(1 pole), lock; Example: hold=3500
def string 'ON' 1-7 'OFF' def is the element status is set after restart, is used for lamp, heating, valve(1 pole); Example: def='ON'
out char[7] 98 'HHHHHHH' Each char is responsible for the type of a particular channel

  • ‘L’-Lamp;
  • ‘M’-Lamp Inverse;
  • ‘J’-Heating NO, valve-heating, normally open;
  • ‘H’-Heating NC, valve-heating, normally closed;
  • ‘B’-Blinds, jalousie/curtains(2 pole);
  • ‘C’-Blinds Inverse, jalousie/curtains, invert open-close(2 pole);
  • ‘G’-Gate (2 pole), 2 pole gate;
  • ‘D’-Gate (2 pole) Inverse, 2 pole gate, invert open-close;
  • ‘X’-Gate (1 pole /short press), 1 pole gate;
  • ‘Z’-Gate (1 pole) Inverse, 1 pole gate, invert open-close;
  • ‘V’-Valve (2 pole), 2 pole valve;
  • ‘W’-Valve (2 pole) Inverse, 2 pole valve, invert open-close;
  • ‘R’-Valve (1 pole), 1 pole valve,;
  • ‘S’-Valve (1 pole) Inverse, 1 pole valve, invert open-close;
  • ‘K’-Lock (short press);
  • ‘N’-Lock (short press) Inverse;
  • ‘F’-FanCoil. Group1 (Lamp Toggle). For fancoil speed control;
  • ‘E’-FanCoil. Group2 (Lamp Toggle). For fancoil speed control;
  • ‘Q’-FanCoil. Group3 (Lamp Toggle). For fancoil speed control;
  • ‘U’-FanCoil. Group4 (Lamp Toggle). For fancoil speed control;
  • ‘I’-FanCoil. Group5 (Lamp Toggle). For fancoil speed control;
  • ‘-‘-none, nothing is connected.


scale float 11-22 '1' Multiplier values offset settings is set by means of scale parameter.
[0..8] – multiplier determines the slope of values (except temperature sensors).
For example, multiplier is 1.1:

offset float SubID of OW temperature sensors '0' [+/- 0..39] – sensor values offset;
For example, offset is -3.8 :

in char[12] 98 'KKKKKKKKKKKK' Each char is responsible for the type of a particular channel

  • ‘B’-Button;
  • ‘C’-Inverted button;
  • ‘S’-Switch;
  • ‘K’-Contact;
  • ‘H’-Inverted contact;
  • ‘L’-Leak, ​Built-in floor leakage sensor;
  • ‘N’-Neptun, ​on-the-floor leakage sensor;
  • ‘M’-Motion, ​motion sensor;
  • ‘-‘-none




<item addr="479:1" auto-period="600" cfgid="42" name="Lamp" type="lamp" uniq_id="145" hw="def='ON'"/>
<item addr="479:2" cfgid="42" name="Radiator" type="valve-heating" uniq_id="146" hw="def='ON'">
  <automation name="Eco" temperature-level="16" uniq_id="147"/>
  <automation name="Comfort" temperature-level="22" uniq_id="148"/>
  <automation name="Hot" temperature-level="25" uniq_id="149"/>
<item addr="479:3" cfgid="42" name="Gate" sub-type="120" type="gate" uniq_id="150" hw="runtime=25"/>
<item addr="479:5" cfgid="42" name="Jalousie" sub-type="120" type="jalousie" uniq_id="151" hw="runtime=50"/>
<item addr="479:7" cfgid="42" name="Valve" type="valve" uniq_id="152" hw="def='ON'"/>
<item addr="479:11" cfgid="42" name="Switch" type="switch" uniq_id="153"/>
<item addr="479:12" cfgid="42" name="Switch" type="switch" uniq_id="154"/>
<item addr="479:13" cfgid="42" name="Door" type="door-sensor" uniq_id="133"/>
<item addr="479:14" cfgid="42" name="Door" type="door-sensor" uniq_id="134"/>
<item addr="479:15" cfgid="42" name="Leak" type="leak-sensor" uniq_id="155"/>
<item addr="479:16" cfgid="42" name="Leak" type="leak-sensor" uniq_id="156"/>
<item addr="479:17" cfgid="42" name="Motion" type="motion-sensor" uniq_id="157"/>
<item addr="479:18" cfgid="42" name="Door" type="door-sensor" uniq_id="138"/>
<item addr="479:20" cfgid="42" name="Door" type="door-sensor" uniq_id="140"/>
<item addr="479:21" cfgid="42" name="Motion" type="motion-sensor" uniq_id="158"/>
<item addr="479:97" cfgid="42" name="Temperature" system="yes" type="temperature-sensor" uniq_id="143"/>
<item addr="479:98" cfgid="42" hw="out='LHG-B-R' in='CSKHLNMK-KM-'" name="Temperature" system="yes" type="temperature-sensor" uniq_id="144"/>