Line 84: |
Line 84: |
| {| class="wikitable" | | {| class="wikitable" |
| |- | | |- |
− | ! Universalausgänge können verwendet werden zur Steuerung von: ! Mit den Universaleingängen können Sie anschließen: | + | ! Universalausgänge können verwendet werden zur Steuerung von: !! Mit den Universaleingängen können Sie anschließen: |
| |- | | |- |
| | Beleuchtung || Taster/LED-Taster/Schalteinheiten | | | Beleuchtung || Taster/LED-Taster/Schalteinheiten |
Line 588: |
Line 588: |
| *z' - WS2812B-Zeichenfolge | | *z' - WS2812B-Zeichenfolge |
| | | |
− | *'e' - led-button inverse | + | *e' - led-taste invers |
− | *'d' - led-button | + | *'d' - led-taste |
− | *'c' - button inverse | + | *'c' - Taste invers |
− | *'b' - button | + | *'b' - Taster |
− | *'s' - switch | + | *'s' - Schalter |
− | *'k' - contact inverse | + | *'k' - Kontakt invers |
− | *'h' - contact | + | *'h' - Kontakt |
− | *'l' - leak | + | *'l' - Leck |
| *'n' - Neptun | | *'n' - Neptun |
− | *'v' - motion inverse | + | *'v' - Bewegung invers |
− | *'m' - motion | + | *'m' - Bewegung |
− | *'r' - thermo-resistor | + | *'r' - Thermowiderstand |
| *'t' - DALLAS | | *'t' - DALLAS |
− | | + | *'-' - keine |
− | *'-' - none | + | Beispiel: io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK' |
− | Example: io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'
| + | |- |
| + | |hw||string||98||-||hw="...", wobei |
| + | *pwm_invert - PWM-Invertierung [1, 0]; |
| + | *lbn_bright - Helligkeit der LED-Tasten, Bereich (0 - 255); |
| + | *f - standardmäßig ist die PWM-Frequenz 1000, Bereich (1 - 5000). |
| + | Beispiel: |
| + | <syntaxhighlight lang="xml" line> |
| + | hw="io='4---zdd----t--' pwm_invert=1 lbn_bright=255 f=1000" |
| + | </syntaxhighlight> |
| |- | | |- |
− | |colspan="3"|'''Only for Metaforsa 3.plus''' | + | |colspan="3"|'''Nur für Metaforsa 3.plus''' |
| |- | | |- |
− | |cfg||string||98||9600/8N1||cfg='SPEED/BPS', where | + | |cfg||string||98||9600/8N1||cfg='SPEED/BPS', wobei |
− | *SPEED – baud rate [1200..115200]; | + | *SPEED - Baudrate [1200..115200]; |
− | *B – data length [7,8]; | + | *B - Datenlänge [7,8]; |
− | *P – presence and type of parity bit [N(No parity),E(Even parity),O(Odd parity)]; | + | *P - Vorhandensein und Art des Paritätsbits [N(Keine Parität),E(Gerade Parität),O(Ungerade Parität)]; |
− | *S – stop bit length [1, 1.5 or 2]. | + | *S - Länge des Stoppbits [1, 1,5 oder 2]. |
− | Example:
| + | Beispiel: |
| <syntaxhighlight lang="xml" line> | | <syntaxhighlight lang="xml" line> |
| hw="cfg='9600/8N1'" | | hw="cfg='9600/8N1'" |
| </syntaxhighlight> | | </syntaxhighlight> |
| |- | | |- |
− | |[Protocol]||string||98||—||Protocol setting is described by protocol parameter. The following | + | |[Protocol]||string||98||—||Die Protokolleinstellung wird durch Protokollparameter beschrieben. Die folgenden |
− | protocols are supported:
| + | Protokolle werden unterstützt: |
− | *'modbus', Modbus protocol, at the end of redirection the checksum CRC16(Modbus) is added; | + | *'modbus', Modbus-Protokoll, am Ende der Umleitung wird die Prüfsumme CRC16 (Modbus) hinzugefügt; |
− | *'dmx', DMX protocol; | + | *'dmx', DMX-Protokoll; |
− | *'CO2' for connecting Larnitech CO2 sensors; | + | *'CO2' für den Anschluss von Larnitech CO2-Sensoren; |
− | *'salda' for connecting Salda ventilation. | + | *'salda' für den Anschluss der Salda-Lüftung. |
− | Example:
| + | Beispiel: |
| <syntaxhighlight lang="xml" line> | | <syntaxhighlight lang="xml" line> |
| hw="cfg='9600/8N1' modbus" | | hw="cfg='9600/8N1' modbus" |
| </syntaxhighlight> | | </syntaxhighlight> |
| |- | | |- |
− | |echo||on; off||98||'off'||For settings check out and testing echo parameter can be used. Module | + | |echo||on; off||98||'off'||Zum Einstellen und Testen können die Echo-Parameter verwendet werden. Modul |
− | echo-reply can be turned on or off with the help of this parameter.Echo parameter value: | + | echo-reply kann mit Hilfe dieses Parameters ein- oder ausgeschaltet werden.echo parameter value: |
| *'off' | | *'off' |
− | *'on' | + | *'ein' |
− | Example:
| + | Beispiel: |
| <syntaxhighlight lang="xml" line> | | <syntaxhighlight lang="xml" line> |
| hw="cfg='9600/8N1' echo='off'" | | hw="cfg='9600/8N1' echo='off'" |