Line 587: |
Line 587: |
| *'z' - WS2812B -chaîne | | *'z' - WS2812B -chaîne |
| | | |
− | *'e' - bouton LED inversé | + | *'e' - bouton led inverse |
− | *'d' - bouton LED | + | *'d' - bouton à led |
− | *'c' - bouton inversé | + | *'c' - bouton inverse |
| *'b' - bouton | | *'b' - bouton |
| *'s' - interrupteur | | *'s' - interrupteur |
− | *'k' - contact inverse | + | *k" - contact inversé |
| *'h' - contact | | *'h' - contact |
| *'l' - fuite | | *'l' - fuite |
− | *'n' - Neptune | + | *'n' - Neptun |
| *'v' - mouvement inverse | | *'v' - mouvement inverse |
| *'m' - mouvement | | *'m' - mouvement |
− | *'r' - thermo-résistance | + | * "r" - thermorésistance |
− | *'t' - DALLAS | + | * "t" - DALLAS |
− | | + | *'-' - aucun |
− | *'-' - none | + | Exemple : io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK' |
− | Example: io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'
| |
| |- | | |- |
− | |colspan="3"|'''Only for Metaforsa 3.plus''' | + | |hw||string||98||-||hw="...", où |
| + | *pwm_invert - Inversion PWM [1, 0] ; |
| + | *lbn_bright - luminosité des boutons à DEL, plage (0 - 255) ; |
| + | *f - la fréquence PWM par défaut est de 1000, plage (1 - 5000). |
| + | Exemple : |
| + | <syntaxhighlight lang="xml" line> |
| + | hw="io='4---zdd----t--' pwm_invert=1 lbn_bright=255 f=1000" |
| + | </syntaxhighlight> |
| + | |- |
| + | |colspan="3"|'''Uniquement pour Metaforsa 3.plus''' |
| |- | | |- |
− | |cfg||string||98||9600/8N1||cfg='SPEED/BPS', where | + | |cfg||string||98||9600/8N1||cfg='SPEED/BPS', où |
− | *SPEED – baud rate [1200..115200]; | + | *SPEED - débit en bauds [1200..115200] ; |
− | *B – data length [7,8]; | + | *B - longueur des données [7,8] ; |
− | *P – presence and type of parity bit [N(No parity),E(Even parity),O(Odd parity)]; | + | *P - présence et type de bit de parité [N(No parity),E(Even parity),O(Odd parity)] ; |
− | *S – stop bit length [1, 1.5 or 2]. | + | *S - longueur du bit d'arrêt [1, 1,5 ou 2]. |
− | Example:
| + | Exemple : |
| <syntaxhighlight lang="xml" line> | | <syntaxhighlight lang="xml" line> |
| hw="cfg='9600/8N1'" | | hw="cfg='9600/8N1'" |
| </syntaxhighlight> | | </syntaxhighlight> |
| |- | | |- |
− | |[Protocol]||string||98||—||Protocol setting is described by protocol parameter. The following | + | |[Protocol]||string||98||—||Le réglage du protocole est décrit par le paramètre de protocole. Les protocoles suivants |
− | protocols are supported:
| + | Les protocoles suivants sont pris en charge : |
− | *'modbus', Modbus protocol, at the end of redirection the checksum CRC16(Modbus) is added; | + | *'modbus', protocole Modbus, à la fin de la redirection, la somme de contrôle CRC16 (Modbus) est ajoutée ; |
− | *'dmx', DMX protocol; | + | *'dmx', protocole DMX ; |
− | *'CO2' for connecting Larnitech CO2 sensors; | + | *'CO2' pour connecter les capteurs de CO2 de Larnitech ; |
− | *'salda' for connecting Salda ventilation. | + | *'salda' pour connecter la ventilation Salda. |
− | Example:
| + | Exemple : |
| <syntaxhighlight lang="xml" line> | | <syntaxhighlight lang="xml" line> |
| hw="cfg='9600/8N1' modbus" | | hw="cfg='9600/8N1' modbus" |
| </syntaxhighlight> | | </syntaxhighlight> |
| |- | | |- |
− | |echo||on; off||98||'off'||For settings check out and testing echo parameter can be used. Module | + | |echo||on; off||98||'off'||Le paramètre écho peut être utilisé pour vérifier les réglages et les tests. Module |
− | echo-reply can be turned on or off with the help of this parameter.Echo parameter value:
| + | L'écho peut être activé ou désactivé à l'aide de ce paramètre : |
| *'off' | | *'off' |
| *'on' | | *'on' |
− | Example:
| + | Valeur du paramètre d'écho : |
| + | *'off' |
| + | *'on' |
| + | Exemple : |
| <syntaxhighlight lang="xml" line> | | <syntaxhighlight lang="xml" line> |
| hw="cfg='9600/8N1' echo='off'" | | hw="cfg='9600/8N1' echo='off'" |