View source for Metaforsa2 MF-14/bs

<languages/>
{{Infobox module
| name       = MF-14
| image      = Metaforsa2.png
| maxcandev     = 50
| canbuslength  = 800 m (twisted pair 5 cat)
| maxcancurrent = 500 mA
| outCount   = 10
| dimmOut    = 4
| peakl      = 16 A
| peakdl     = 0.5 A (110 W at 220 V)
| dt         = MOSFET
| inDisc     = 24
| inDigit    = 4
| voltage    = 11.5...27.5 V DC
| dim        = 9U, 156x110x58 mm
}}

==Uvod==

Uputstvo za instalaciju METAFORSA SMART HOUSE opisuje proceduru za njegovu instalaciju, montažu, rad i podešavanje.
Dok radite sa sistemom, morate se striktno pridržavati svih zahtjeva navedenih u ovom priručniku. Nepridržavanje može dovesti do oštećenja uređaja, njegovog kvara, strujnog udara, požara i drugih ispada.
Proizvođač zadržava pravo izmjene ovog priručnika bez prethodne najave. Ovaj priručnik je sastavni dio sistema i ostaće krajnjem korisniku.

<youtube>https://youtu.be/gVdNL5v58LI</youtube>

==Karakteristike==
*Podržava 10 univerzalnih izlaza:
**Svjetla
**NC/NO ventili za grijanje
**Blinds
**1 ili 2-polne kapije
**1 ili 2-polni ventili
**NC/NO brave
**Fan coil jedinice
*4 izlaza za zatamnjivanje
*24 diskretna ulaza koji podržavaju:
**Dugmad
**Prekidači
**Tribasti prekidači
**senzori curenja
** detektori pokreta
*4 digitalna ulaza za do 8 temperaturnih senzora
*Priključak za proširenje
*Releji sa AgSnO2 kontaktima predviđeni za udarnu struju od 80A 20ms
*Cloud konekcija i kontrola svih kućnih sistema
*Upravljanje glasom (Siri, Alexa, Google Home)
*Plugins engine omogućava proširenje mogućnosti sistema (npr. integracija sa Satel, Philips Hue, IKEA svjetlima)
*Sigurnost od neovlaštenog upada osigurana RSA/AES256 enkripcijom
*Push obavještenja iz sistema na vašem telefonu (moguće je i primanje putem Telegram i Viber messengera)
*Historija (podaci brojila za godinu dana se čuvaju)
*Plug and play (mogućnost brzog i jednostavnog proširenja sistema)
* Redovna ažuriranja sistema
*Velika baza skripti koja se stalno ažurira kako bi zadovoljila sve vaše potrebe
*Automatsko dnevno sigurnosno kopiranje putem oblaka s mogućnošću vraćanja početne konfiguracije
*Otvoreni API (koji omogućava integraciju Larnitecha u druge sisteme)
*Interaktivno i korisničko sučelje LT SETUP dostupno za naprednu konfiguraciju
*Plug and play
*To je komplet sistema Smart Home spreman za instalaciju

==Sigurnosni zahtjevi== 


<div class="caution">'''OPREZ! Sve radove vezane za instalaciju, povezivanje, postavljanje, servis i podršku mora izvoditi kvalifikovano osoblje sa dovoljnim vještinama i iskustvom u radu sa električnom opremom.'''
</div>
Kako bi se izbjegao rizik od požara, strujnog udara, oštećenja sistema i/ili ličnih ozljeda, instalacija i montaža sistema moraju se izvesti u skladu sa uputstvima navedenim u nastavku:


*svi radovi na priključenju moraju se izvoditi bez struje;
*koristite odgovarajući alat i ličnu zaštitu od strujnog udara;
*ne koristite oštećene kablove, žice i konektore;
*izbjegavajte savijanje kablova i žica;
*nemojte štipati ili savijati kablove i žice primenom prekomerne sile. U suprotnom, unutrašnji provodnici kabla i žica mogu biti ogoljeni ili slomljeni;
*nemojte koristiti strujnu utičnicu sa lošim kontaktima za povezivanje;
*nemojte prekoračiti ograničenje parametara opterećenja navedeno u ovom priručniku;
*presjek žice provodnika za napajanje podliježe specifikacijama za ograničenje gustine struje, vrstu izolacije i materijal žice. Lagani dio može dovesti do pregrijavanja kabla i požara.


Prilikom rada sa sistemom nakon napajanja naponom '''NIKAD''':
*izvršiti spajanje/odspajanje konektora;
*otvoreni moduli i senzori.

==Konfiguracija sistema i svrha== 

===Svrha sistema=== 


METAFORSA SMART HOUSE je gotovo rešenje za automatizaciju stambenih i poslovnih prostora, hotelskih kompleksa koje uključuje najpoželjnije karakteristike Pametne kuće.


Uređaj ima 10 kontrolnih kanala, 4 kanala za zatamnjivanje, 24 ulazna senzorska kanala i port za povezivanje digitalnih senzora.


{| class="wikitable"
|-
! Univerzalni izlazi se mogu koristiti za upravljanje: !! Univerzalni ulazi vam omogućavaju da povežete:
|-
| Rasveta || Tasteri/prekidači
|-
| Utičnice || Magnetni reed prekidači
|-
| Podno grijanje || Senzori pokreta
|-
| Aktivatori za zavjese/kapije || Senzori curenja
|-
| Ventili za vodoopskrbu/grijanje ||
|}



'''Priključak za povezivanje digitalnih senzora'''


Port za povezivanje digitalnih senzora omogućava vam da povežete različite digitalne senzore, kao što su senzori temperature, ambijentalnog svetla, vlažnosti i drugih.


'''Port za proširenje'''


Port za proširenje omogućava nadogradnju sistema povezivanjem pomoćne opreme, kao što je upravljački modul za LED rasvjetu, dimiranje, mjerne uređaje i druge elemente.
Paket, koji je potpuno spreman za instalaciju, uključuje osnovni hardver i softver.

===Sadržaj paketa=== 


Paket standardno dolazi sa:
{| class="wikitable"
|-
| Mainframe METAFORSA MF-14.A || 1 kom
|-
| Jedinica za napajanje MEANWELL DR-15-12 || 1 kom
|-
| Senzor pokreta CW-MSD || 3 kom
|-
| Senzor curenja FW-WL.A || 2 kom
|-
| Element osjetljiv na temperaturu FW-TS.A || 4 kom
|-
| Magnetski reed prekidač (senzor položaja prozora/vrata) || 4 kom
|-
| Filter šuma za Ethernet kabl || 1 kom
|-
| Kabl za napajanje || 1 kom
|}

===Osnovne tehničke specifikacije sistema=== 

Osnovne specifikacije i karakteristike modula METAFORSA MF-14.A prikazane su u tabeli 1
{| class="wikitable"
|+ style="text-align:left;" | Table1
|-
!Specifikacija !! Značenje
|-
|colspan="2"|'''Output ports'''
|-
| Number of switched channels || 10 
|-
| Number of switched groups|| 10 
|-
| Number of dimming channels || 4 
|-
| Commutation voltage || 0-250 V AC/DC 
|-
| Peak load (one channel) || 16A 
|-
| Peak load (device) || 160A 
|-
| Max load per dimming channel || 0.5A (110W at 220V) 
|-
| Dimmer type || MOSFET 
|-
| Dimmer load type || R,C
|-
| Dimming type || trailing edge 
|-
| Power supply cable connection type || connector 
|-
|Permissible section of power supply cable to connect in socket:<br>single-conductor cable<br>multiple-conductor cable<br>tipped multiple-conductor cable||<br>0.5 … 4mm2<br>0.5 … 4mm2<br>0.5 … 2.5mm2
|-
|colspan="2"|'''Input ports'''
|-
|Number of discrete inputs || 24
|- 
|Number of digital inputs || 4 
|-
|Current maximum rating on the direct-current voltage connectors || 50mA 
|-
|colspan="2"|'''Izlazni portovi'''
|-
| Broj komutiranih kanala || 10
|-
| Broj komutiranih grupa|| 10
|-
| Broj kanala za zatamnjivanje || 4
|-
| Komutacijski napon || 0-250 V AC/DC
|-
| Vršno opterećenje (jedan kanal) || 16A
|-
| Vršno opterećenje (uređaj) || 160A
|-
| Maksimalno opterećenje po kanalu za zatamnjenje || 0.5A (110W na 220V)
|-
| Tip dimera || MOSFET
|-
| Tip opterećenja dimera || R,C
|-
| Vrsta zatamnjenja || zadnja ivica
|-
| Vrsta priključka kabla za napajanje || konektor
|-
|Dozvoljeni deo kabla za napajanje za povezivanje u utičnicu:<br>jednožilni kabl<br>kabl sa više provodnika<br>kabl sa više provodnika||<br>0,5 … 4mm2<br>0,5 … 4mm2<br >0,5 … 2,5 mm2
|-
|colspan="2"|'''Ulazni portovi'''
|-
|Broj diskretnih ulaza || 24
|-
|Broj digitalnih ulaza || 4
|-
|Maksimalna struja na konektorima jednosmjernog napona || 50mA
|-
|colspan="2"|'''Ostalo'''
|-
|Radna temperatura okoline || 0 … +45°S
|-
|temperatura skladištenja/transporta || -20 … +60°S
|-
|Dozvoljena vlažnost || 0 … 95% (bez kondenzacije)
|-
|Napajanje || 12 … 27,5 V DC<br>24V, 0,75A Preporučeno
|-
|Maksimalna potražnja || 0.5A
|-
|Dostupni interfejsi || Ethernet, CAN, OneWire
|-
|Tip autobusa || CAN (4-žični)
|-
|CAN (4-žični) || 800 m* (upredeni par 5 mačaka)
|-
|CAN tip žice || FTP Cat 5E
|-
|CAN tip veze || konektor
|-
|Maksimalna dužina digitalne linije || 30 m
|-
|Digitalni linijski tip žice || UTP/FTP Cat 5E
|-
|LAN maksimalna dužina || 100 m
|-
|vrsta LAN žice || UTP/FTP Cat 5E
|-
|vrsta LAN veze || Konektor RJ-45
|-
|Dimenzionalne specifikacije || 9U, 156x110x58 mm
|-
|Materijal ljuske || ABS plastika
|-
|Kućište || IP40
|-
|Tip ugradnje opreme || DIN šina (EN 60715)
|-
|Težina || 400 g
|}
<nowiki>*</nowiki> – potrebno je instaliranje dodatnih jedinica za napajanje za duge linije; maksimalna dužina linije može biti smanjena različitim faktorima interferencije

===Opća struktura sistema=== 


Module general view is shown in '''fig. 1'''


[[File:Mf14.ch.png|700px|frameless|left|Fig. 1 Module general view]]
<br>
{| class="wikitable" style="clear:left;"
|-
|1 || — connector for load application
|-
|2 || — connector for dimming-lamps application
|-
|3 || — power connector
|-
|4 || — Ethernet network connector
|-
|5-6 || — connectors for digital sensors and buttons/switching units
|-
|7 || — OneWire interface connector (for digital sensors)
|-
|8 || — connector for expansion module.
|}


'''Overview of the METAFORSA device external connectors:'''
At the top of the casing ('''fig. 1''') there is:


*connector (1) — Devices connection;
*connector (2) — Dimming lamps connection;


At the bottom of the casing ('''fig. 1''') there is:


*connector (3) — module power supply connection;
*connector (4) — Ethernet network connection;
*connectors (5-6) — four six-point connectors for digital sensors connection – motion, leakage, reed switch sensors, and *button/switching unit sensors;
*connector (7) — OneWire digital sensors bus connection;
*connector (8) — expansion module connection.
The physical configuration and contact point assignment of each connector are shown in '''table 2'''.


{| class="wikitable"
|+ text-align="left"|'''Table2'''
|-
!Connector!!Contact!!Assignment
|-
|[[File:Out.png|80px|frameless]] ||1-10|| Load application (light lamps, thermal actuators, etc.)
|-
|[[File:Dimm.png|80px|frameless]] ||D1-4, L, N|| Load application (dimming lamps)
|-
| colspan="2"| Device status indicators || The module status indicators are described in '''table 3'''
|-
|[[File:24vconn.png|80px|frameless]] ||+24V<br>GND|| +24V — module power supply by an external 24 V power supply GND — common
|-
|[[File:Rj45.jpg|80px|frameless]] ||RJ45|| Connector for LAN connectivity
|-
|[[File:Inputs.png|80px|frameless]] ||In1-12, In13-24 GND|| Controlling devices connection (buttons, magnetic reed switches, motion or leakage sensors): +12V — sensor power output +12 V<br>In1 … In24 — logic inputs (0-12 V)<br>GND — common
|-
|[[File:OW.png|80px|frameless]] ||OneWire|| Digital sensors connection (temperature)<br>VCC — sensors power supply output +5V<br>OW1-OW4 — OneWire data buses<br>GND — common
|-
|[[File:Can.jpg|80px|frameless]] ||VCC<br>GND<br>L<br>H|| External modules connection for CAN-bus<br>VСС — 24V output for external devices power supply<br>GND — common<br>L — CAN-L data bus<br>H — CAN-H data bus
|}

{{indicationmfold}}

===System installation and assembly===
Before connecting the system, you must:


*site the sensor and actuators (if not pre-installed), set the sensors and actuators;
*site the module and power supply.


'''Note: The module must be installed near the power supply voltage source.'''


<div class="cautoin">CAUTION!
AC power voltage must be provided to the system input through the circuit breaker assembly. It should be installed close to the power supply.</div>
#'''The power of circuit breaker assembly must comply with the load capacity;'''
#'''Nothing else than the phase conductors can be connected to the module, the neutral wire is connected separately.'''


Typical diagram of METAFORSA MF-14.A module connection is shown in '''fig. 3.'''
<div style="clear: both">[[File:Mf14chcon.png|700px|Fig. 3]]</div>



===Connection of the actuators===



====Connection of the lights/electric contactor/heating thermal actuator====

{| class="wikitable" style="width:800px";
|-
|[[File:lamps.png|350px|lamp]]<br>'''Fig. 4'''|| style="margin:20px"|Such actuators as light, electric contactor, heating thermal actuator should be switched on any of the outputs 1 – 10, the neutral wire and the ground wire should be connected directly to the switchboard. The example of connection is shown in '''Fig.4'''.
|}



====Connection of high load device====

{| class="wikitable" style="width:800px";
|-
|[[File:Contactor.png|350px|Contactor]]|| style="margin:20px"|Recomended contactors:
*ABB ESB series
*Schneider Acti 9 iCT series
*Hager ESC series.
|}



====Connection of single-pole water/gas supply valve====

{| class="wikitable" style="width:800px";
|-
|colspan="2" style="background-color:#dededf" |'''Caution: Before applying power to the load, make sure that the output configuration of METAFORSA module is correct. The incorrect configuration or incorrect connection can cause the module failure and/or failure of the equipment connected to it, and even a fire.'''
|-
|[[File:1pvalve.png|350px|valve]]<br>'''Fig. 5'''|| style="margin:20px"|The single pole water/gas supply valve is connected to any of the outputs of 1 – 10, the (neutral wire and the ground wire are connected directly to the switchboard. The example of connection is shown in '''Fig.5'''.
|}



====Connection of double-pole water/gas supply valve====

{| class="wikitable" style="width:800px";
|-
|colspan="2" style="background-color:#dededf" |'''Caution: Before applying power to the valve, it is necessary to ensure the output configuration of METAFORSA module is correct. The incorrect configuration can cause the voltage application simultaneously to both channels of the valve, which may result in the module failure and/or failure of the equipment connected to it, and even a fire.'''
|-
|[[File:2pvalve.png|350px|valve]]<br>'''Fig. 6'''|| style="margin:20px"|Two adjacent contact points (for example, 3, 4) are used to connect the double-pole water/gas supply valve; in these conditions the neutral wire and the ground wire are connected directly to the switchboard. The example of connection is shown in '''Fig.6'''.
|}



====Connection of single-pole gate actuator====

{{ConExC
|Caution: Before applying power to the module, you should properly configure access to the application. The contacts incorrectly configured can result in the module failure and/or failure of the equipment connected to it, and even a fire.
|1pgate|Fig. 7|Any contact point (for example, 3) is used to connect the single-pole gate drive controllers. The example of connection is shown in '''Fig.7'''.
}}



====Connection of double-pole gate actuator====

{{ConExC
|Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
|2pgate|Fig. 8|Two adjacent contact points (for example, 3, 4) should be used to connect the double-pole gate drive controller. The example of connection is shown in '''Fig.8'''.
}}



====Connection of curtain/jalousie/shutter actuator with 220V force control====

{{ConExC
|Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
|Pjalousie|Fig. 9|Two adjacent contact points (for example, 3, 4) should be used to connect the curtain/jalousie/rolladens actuator, in these conditions the neutral wire and the ground wire are connected directly to the switchboard. The example of connection is shown in '''Fig.9.'''
}}



====Connection of curtain/jalousie/shutter actuator with low-voltage control====

{{ConExC
|Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
|ljalousie|Fig. 10|Two adjacent contact points (for example, 3, 4) should be used to connect the curtain/jalousie/rolladens actuator with low-voltage control. The example of connection is shown in '''Fig.10'''.
}}

===Connection of sensing elements/switches/buttons===

====Connection of motion sensors====

The motion sensors should be connected to any free input in1-in24; in these conditions their power is connected to the contact points of +12V and GND of the relevant group. The example of connection is shown in '''Fig.11'''.

[[File:msConn.png|300px|ms]]
<br>
'''Fig. 11'''


====Connection of FW-WL.A leakage sensors====

FW-WL.A leakage sensors are connected to any free input in1 – in24, in these conditions the power should be connected to +12V and GND points of the relevant group. The example of connection is shown in '''fig. 12'''.
{| style="width"700px"
|- style="tezt-align:center;"
|[[File:Leak1.png|300px|center]]<br>'''Fig12'''||[[File:Leak2.png|300px|center]]<br>'''Fig13'''
|}

Configuration and connection of the FW-WL.A sensor
1. Terminals:
:'''+12V''' — sensor power is connected to the contact point of METAFORSA “+12V”;
:'''OW''' — sensor pickup signal;
:'''GND''' — common, connected to GND contact of METAFORSA.
2. Sensor preset switch (optionally):
:1 — sensor sensitivity (ON – high, OFF – low);
:2 — indicator colour setting (ON – blue, OFF – green).
3. LED status indicator.

====Connection of buttons/switches/magnetic reed switches====

Buttons and reed switches are connected to any free input in1-in24, while their second contact point is connected to GND point of the relevant METAFORSA module group, + 12V power outputs – not in use. The example of connection is shown in '''Fig. 14-15'''.
{| style="width"700px"
|- style="tezt-align:center;"
|[[File:Buttons.png|300px|center]]<br>'''Fig14''' connection of buttons/switching units || [[File:Reed-sv.png|300px|center]]<br>'''Fig15''' connection of the magnetic reed switches (window/door position sensors)
|}

====Connection of digital sensors====

The OW adapter ('''Fig. 16a''') is supplied along with METAFORSA module with the possibility to connect up to 8 digital sensors to it. In these conditions, several devices can be connected to one channel ('''Fig. 16b'''). The connected sensors are detected automatically and do not require any original setting.

{| style="width"700px"
|- style="tezt-align:center;"
|[[File:Ow1Conn.png|300px|center]]<br>'''Fig16 a'''||[[File:Ow2Conn.png|300px|center]]<br>'''Fig16 b'''
|}
'''Configuration and connection of the OW adapter'''
<div style="width:700px; background-rgb:#dededf">'''Caution: Ensure the connection is correct. The incorrect connection may cause sensor and/or module malfunction. '''</div>

===Connection of auxiliary equipment.===

Expansion modules include Larnitech equipment connected through the CAN-bus. Such equipment includes: dimmers, RGB-backlit control modules, multimode sensors, etc. The equipment connected to the expansion port is defined automatically and does not require any preset tuning. Connector contact pin assignment is defined in '''Table 4.''' The example of connection is shown in '''Fig. 17'''.

{| class="wikitable" style="width:700px"
|-
|[[File:Canex.png|700px]]
|-
|style="background-color:#dededf"|'''Caution! The 120 ohm terminating resistors should be installed at the end connectors between L and H contact points of CAN-bus. Ensure the connection is correct. The incorrect connection may cause sensor and/or module malfunction.'''
|}

===Module installation and connection procedure===
<div style="width:700px; background-color:#dededf">'''
ATTENTION! You must precisely follow the recommendations listed in the Security Requirements section hereof.'''</div>

#Install the module in the switchboard on the DIN-rail and fix it with the special latch on the module base.
#Fasten the supply unit on the left side of the module.
#Connect the connector (4) having the noise filter pre-installed which is supplied complete with the module.
#Connect the connectors (5), (6).
#Connect the connectors (1), (2).
#Connect the connector (3).
#Apply power to the supply unit of METAFORSA module.
#Wait until the module is loaded, then configure it in accordance with the '''System Setup Instructions.'''
#Apply power to the connectors (1), (2).
#Check all equipment for proper operation.

===METAFORSA module shut-off and deinstallation procedure===

#De-energize the module by disconnecting the circuit breaker assembly of the load power supply and METAFORSA module supply unit. Verify the voltage is absent on the terminals (1), (2) of the connector wires and on the input terminals of the supply unit.
#Disconnect the load power supply connectors (1), (2).
#Disconnect the connector (3).
#Disconnect the connectors (4)-(6).
#Remove the module from the DIN-rail, releasing the latch at the bottom of the module base.

==Hardware setup==

To configure and control METAFORSA SMART HOUSE, you must install Larnitech software on your smartphone or tablet, which is available in [https://itunes.apple.com/us/app/larnitech/id1108457530?mt=8 App Store] and [https://play.google.com/store/apps/details?id=com.larnitech Play Market]. After installation, follow the '''System Setup Instructions'''.

==Fault diagnostics and handling==

The following are some possible faults and ways of fault handling. If you have any difficulty, or face the fault undeclared here, please contact the Technical Support: [http://www.larnitech.com/support/] or [support@larnitech.com].
There are also some tips in the FAQ section at our website [http://www.larnitech.com/faq/].

===The actuators do not operate:===

*ensure the outputs are properly configured in the application (see '''System Setup Instructions''');
*check the connection is correct in accordance with '''table 2 and''' paragraph 3.6;
*ensure the power is supplied to the input power contact , i.e. all circuit breaker assembly are ON.
*verify the operability of the connected equipment.

===The module is off, indication absent:===

*check the connection to 24V supply unit as shown in '''table 2''' (contacts pin assignment);
*check the connection of the supply unit to 220V power mains, the indicator should be ON.

===Network connection fault:===

*ensure the Ethernet cable is properly wired and connected to the connector;
*ensure the LED status indicators are ON on the Ethernet connector;
*check the LAN configuration is correct, Ethernet cable loops are absent;
*METAFORSA module and the device you are connecting from are in the same network.

hold integer 0-10000 1-10 by default hold is the same as runtime
hold is the bridging time in miliseconds, is used for gate and jalousie, lock; Example: hold=3500


===The sensors do not operate:===

*ensure the inputs are properly configured in the application ('''System Setup Instructions''');
*check the connection is correct in accordance with '''table 2''' and paragraph 3.7;
*ensure the METAFORSA module is ON: circuit breaker assembly is closed, indication on the supply unit is ON, the module indication corresponds to the operating status – '''table 3''';
*check the power supply availability on the sensors;
*check the integrity of lines laid to the sensors.

===The auxiliary equipment does not operate:===

*check the connection is correct in accordance with table 2 and paragraph 3.8-9;
*ensure the METAFORSA module is ON: circuit breaker assembly is closed, indication on the supply unit is ON, the module indication corresponds to the operating status – table 3;
*check the integrity of the CAN lines, voltage supply on the modules.

==HW Settings==
{| class="wikitable"
|-
!Name!!Type, range!!SUBID!!Default!!Description
|-
|runtime||integer 0-100 || 1-10 || 15 ||runtime is the open/close time in seconds, is used for jalousie, gate, valve(2 pole); 
<br>Example: runtime=15
|-
|runtimeopen||integer 0-60000||Blinds subId || ||Runtimeopen is the open time in milliseconds, is used for blinds; Example: runtimeopen=15000
|-
|runtimeclose||integer 0-60000||Blinds subId|| ||Runtimeclose is the close time in milliseconds, is used for blinds; Example: runtimeclose=15000
|-
|hold||integer 0-10000||1-10||500||hold is the bridging time in milliseconds, is used for gate and jalousie (by default hold is the same as runtime for jalousie and gate), lock; Example: hold=3500
|-
|def||string 'ON'||1-10||'OFF'||def is the element status is set after restart, is used for lamp, heating, valve(1 pole); Example: def='ON'
|-
|stop||Char ‘R’||1-7||–||(for 2-pole gate and blinds) If it is declared then by Stop command during the motion, the same impulse appears as it was at the beginning of the motion. Pole, an which the stop-impules is formed, is defined by the parameter Stop value. If it is ‘r’ or ‘R’ then stop-impulse is produced on the opposite to the start-impulse pole. If any other value is delcared (e.g., ‘d’ ) then the stop-impulse is on the same pole. If a Runtime passed after the beginning of the motion then the stop-impulse is not formed. Example: stop=’r’
|-
|out||char[10]||98||'LLLLHHHHP-'||Each char is responsible for the type of a particular channel
*'L'-Lamp;
*'M'-Lamp Inverse;
*'J'-Heating NO, valve-heating, normally open;
*'H'-Heating NC, valve-heating, normally closed;
*'B'-Blinds (2 pole), jalousie/curtains;
*'C'-Blinds Inverse (2 pole), jalousie/curtains, invert open-close;
*'G'-Gate (2 pole), 2 pole gate;
*'D'-Gate (2 pole) Inverse, 2 pole gate, invert open-close;
*'X'-Gate (1 pole /short press), 1 pole gate;
*'Z'-Gate (1 pole) Inverse, 1 pole gate, invert open-close;
*'V'-Valve (2 pole), 2 pole valve;
*'W'-Valve (2 pole) Inverse, 2 pole valve, invert open-close;
*'R'-Valve (1 pole), 1 pole valve,;
*'S'-Valve (1 pole) Inverse, 1 pole valve, invert open-close;
*'K'-Lock (short press);
*'N'-Lock (short press) Inverse;
*'P'-Blinds (2 pole);
*'O'-Blinds Inverse (2 pole), invert open-close;
*'F'-FanCoil. Group1 (Lamp Toggle). For fancoil speed control;
*'E'-FanCoil. Group2 (Lamp Toggle). For fancoil speed control;
*'Q'-FanCoil. Group3 (Lamp Toggle). For fancoil speed control;
*'U'-FanCoil. Group4 (Lamp Toggle). For fancoil speed control;
*'I'-FanCoil. Group5 (Lamp Toggle). For fancoil speed control;
*'-'-none, nothing is connected.
Example: out='LLB-G-V-W-'
|-
|dm||char[4]||98||‘LLLL’||Each char is responsible for the type of a particular channel
*‘g’ – use like halogen dimer-lamp
*‘s’ – Soft Switch, lamp, when on/off power is supplied/deenergised smoothly (500msec)
*‘k’ – Switch, lamp, when on/off power is supplied/deenergised immediately
*‘l’ – LED Function, dimmable LED lamps
*‘v’ – linear Function of dimming
*‘-‘ – Channel disabled
*‘+’ – Regular channel
Example: dm=’skl-‘
|-
|def||integer 0-250||11-14||100||The default brightness level in case of a power reset (1..250). Example: def=250
|-
|min||integer 0-100||11-14||0||Minimum dimming level, example: min=10
|-
|max||integer 0-100||11-14||100||Maximum dimming level, example max=95
|-
|start||integer 0-100||11-14||0||The Start function is used for lamps that lack the minimal voltage to get turned on. If the set value is lower than the start value, the lamp is turned on at the start value and them the light is dimmed down to the set level. Example: start=60
|-
|force||integer 0-100||11-14||10||Time duration of the starting value (measured in milliseconds). Example: force=20
|-
|runtime||integer 0-60000||11-14||1000||Runtime is the speed of changing the brightness from ‘min’ to ‘max’ (measured in milliseconds). Example: runtime=1000
|-
|offset||integer (+/- 0…39)||39-46||'0'||sensor values offset; For example, offset is -3.8 :
Example: hw="offset='-3.8'"
|-
|in||char[24]||98||'BBBBBBBBBBBBMMMLLLKKKKKK'||Each char is responsible for the type of a particular channel
*'B'-Button;
*'C'-nButton;
*'S'-Switch;
*'K'-Contact;
*'H'-nContact;
*‘L’-Leak, Built-in floor (EW-WL) or on-the-floor (FW-WL) leakage sensor
*‘N’-Third party leakage sensor;
*'M'-Motion, motion sensor;
*'V'-nMotion, motion sensor;
*'-'-none
Example: in='MMMMMMMMMMMMLLLLLLLLLLLL'
12 motion sensors and 12 leak-sensors;
in='BBBBBBBBSSSSSSBBBBSSSSSS'
12 buttons; 12 switches.
|}

<syntaxhighlight lang="xml" line>
<item addr="339:1" auto-period="600" cfgid="40" hw="def='ON'" name="Lamp" type="lamp" uniq_id="3779"> 
<item addr="339:2" cfgid="40" hw="def='ON'" name="Radiator" type="valve-heating" uniq_id="3780"> 
    <automation name="Eco" temperature-level="16" uniq_id="3781"/> 
    <automation name="Comfort" temperature-level="22" uniq_id="3782"/> 
    <automation name="Hot" temperature-level="25" uniq_id="3783"/> 
</item> 
<item addr="339:3" cfgid="40" hw="runtime=9" name="Jalousie" sub-type="120" type="jalousie" uniq_id="32"/> 
<item addr="339:5" cfgid="40" hw="runtime=13" name="Gate" sub-type="120" type="gate" uniq_id="3784"/> 
<item addr="339:7" cfgid="40" hw="hold=4600" name="Gate" sub-type="120" type="gate" uniq_id="3785"/> 
<item addr="339:8" cfgid="40" hw="runtime=10" name="Valve" type="valve" uniq_id="3786"/> 
<item addr="339:11" cfgid="40" name="Motion" type="motion-sensor" uniq_id="17"/> 
<item addr="339:12" cfgid="40" name="Motion" type="motion-sensor" uniq_id="18"/> 
<item addr="339:13" cfgid="40" name="Motion" type="motion-sensor" uniq_id="19"/> 
<item addr="339:16" cfgid="40" name="Leak" type="leak-sensor" uniq_id="21"/> 
<item addr="339:17" cfgid="40" name="Leak" type="leak-sensor" uniq_id="41"/> 
<item addr="339:19" cfgid="40" name="Switch" type="switch" uniq_id="22"/> 
<item addr="339:20" cfgid="40" name="Switch" type="switch" uniq_id="23"/> 
<item addr="339:21" cfgid="40" name="Switch" type="switch" uniq_id="24"/> 
<item addr="339:22" cfgid="40" name="Switch" type="switch" uniq_id="25"/> 
<item addr="339:23" cfgid="40" name="Door" type="door-sensor" uniq_id="26"/>
<item addr="339:24" cfgid="40" name="Door" type="door-sensor" uniq_id="27"/> 
<item addr="339:25" cfgid="40" name="Door" type="door-sensor" uniq_id="28"/> 
<item addr="339:26" cfgid="40" name="Door" type="door-sensor" uniq_id="29"/> 
<item addr="339:30" cfgid="40" name="Temperature" type="temperature-sensor" uniq_id="3772"/> 
<item addr="339:31" cfgid="40" name="Temperature" type="temperature-sensor" uniq_id="3773"/> 
<item addr="339:32" cfgid="40" name="Temperature" type="temperature-sensor" uniq_id="3774"/> 
<item addr="339:33" cfgid="40" hw="offset='-10.8'" name="Temperature" type="temperature-sensor" uniq_id="3775"/> 
<item addr="339:34" cfgid="40" hw="offset='25.1'" name="Temperature" type="temperature-sensor" uniq_id="3776"/> 
<item addr="339:35" cfgid="40" name="Temperature" type="temperature-sensor" uniq_id="3777"/> 
<item addr="339:36" cfgid="40" name="Temperature" type="temperature-sensor" uniq_id="3778"/> 
<item addr="339:98" cfgid="40" hw="out='LHB-G-XV--' in='MMM--LL-BBBBKKKK'" name="Temperature" system="yes" type="temperature-sensor" uniq_id="30"/>
</syntaxhighlight>