https://wiki.larnitech.com/index.php?action=history&feed=atom&title=DW-DISPATCH%2FenDW-DISPATCH/en - Revision history2026-05-14T13:29:08ZRevision history for this page on the wikiMediaWiki 1.35.11https://wiki.larnitech.com/index.php?title=DW-DISPATCH/en&diff=6011&oldid=prevFuzzyBot: Updating to match new version of source page2022-01-08T13:14:35Z<p>Updating to match new version of source page</p>
<p><b>New page</b></p><div><languages/><br />
{{Infobox module<br />
| name = DW-DISPATCH<br />
| image = DW-DISPATCH.png<br />
| outCount = <br />
| dimmOut = <br />
| peakl = <br />
| peakdl = <br />
| dt = <br />
| RS485 = 1<br />
| MBUS = 1<br />
| pInCount = 20<br />
| inDry = <br />
| voltage = 11.5...27.5 V DC<br />
| dim = 4U, 69x104x58 mm<br />
}}<br />
<br />
==AMR (AUTOMATIC METER READING) MODULE==<br />
<br />
This module is for the dispatch system only. It is not used in the main Larnitech Smart Home system.<br />
<br />
<div class="caution"><br />
CAUTION! All work related to the installation, connection, setting up, service and support must be carried out by qualified personnel with sufficient skills and experience in working with electrical equipment.<br />
To avoid the risk of fire, electric shock, damage to the system and/or personal injury, the system installation and assembly must be performed in accordance with the instructions listed below:<br />
*all connectivity work must be carried out with the power turned OFF;<br />
*use appropriate tools and personal protection against electric shock;<br />
*do not use damaged cables, wires and connectors;<br />
*avoid folding the cables and wires;<br />
*do not apply excessive force to the wires by kinking or pressing them too hard: the inner conductors of the cables and wires may get stripped or damaged;<br />
*do not use the power socket with poor contacts to connect;<br />
*do not exceed the load limit parameters specified in the manual;<br />
*the supply conductors wire section is subject to the specifications for current density limit, insulation type and wire material. Light section can result in cable overheating and fire.<br />
When the power is on, NEVER:<br />
*connect/disconnect the connectors;<br />
*open modules and sensors.<br />
</div><br />
<br />
==Overview==<br />
<br />
[[File:DISPATCH VIEW.jpg|500px]]<br />
<br />
==Module dimensions==<br />
<br />
[[File:DISPATCH DIM.png|500px]]<br />
<br />
==Example of connection==<br />
<br />
[[File:DISPATCH EXA.jpg|500px]]<br />
<br />
==Module parameters==<br />
<br />
{{ Mp<br />
| rs485qty = 1<br />
| mbusqty = 1<br />
| pulseiqty = 20<br />
| power = 11.5 … 27.5 V DC from CAN<br />
| maxcur24v = 45 mA<br />
| buttonreclen = 300m<br />
| bustype = CAN (4-wire)<br />
| instalation = DIN-rail (EN 60715)<br />
| case = ABS<br />
| protection = IP40<br />
| temprange = -10 … +50 °C<br />
| size = 4U, 69x104x58 mm<br />
| weight = 130g<br />
}}<br />
<br />
==Indication of module operation==<br />
{{indicationold}}<br />
<br />
==Module installation and connection procedure==<br />
#Install the module in the switchboard on the DIN rail and fix it with the special latch on the module base.<br />
#Connect the X1-X4 connectors.<br />
#Connect the CAN connector.<br />
#Configure the module using LT setup.<br />
#Check all equipment for proper operation.<br />
<br />
==Module shut-off and deinstallation procedure==<br />
#Disconnect the CAN connector.<br />
#Disconnect the X1-X4 connectors.<br />
#Remove the module from the DIN rail, releasing the latch at the bottom of the module base.</div>FuzzyBot