DW-ME - Revision history

Support at 08:42, 8 December 2022

2022-12-08T08:42:52Z

Support at 08:24, 8 December 2022

2022-12-08T08:24:01Z

Rusanov: Marked this version for translation

2022-01-08T12:46:18Z

Marked this version for translation

Rusanov at 12:46, 8 January 2022

2022-01-08T12:46:03Z

Erich: /* Example of connection */

2021-08-13T08:31:39Z

Example of connection

Erich: Created page with " {{Infobox module | name = DW-ME.C | image = DW-MEC.png | UART = 1 | dts = 1200-115200 b/s | voltage..."

2021-08-13T08:31:22Z

Created page with " {{Infobox module | name = DW-ME.C | image = DW-MEC.png | UART = 1 | dts = 1200-115200 b/s | voltage..."

New page

{{Infobox module
| name = DW-ME.C
| image = DW-MEC.png
| UART = 1
| dts = 1200-115200 b/s
| voltage = 11.5...27.5 V DC
| dim = 2U, 36x97x58 mm
}}

==AC ADAPTER==

This module is designed for interface adjustment between the AC which have the UART interface (TTL levels) and the Smart Home system.

<div class="caution">
CAUTION! All work related to the installation, connection, setting up, service and support must be carried out by qualified personnel with sufficient skills and experience in working with electrical equipment.
To avoid the risk of fire, electric shock, damage to the system and/or personal injury, the system installation and assembly must be performed in accordance with the instructions listed below:
*all connectivity work must be carried out with the power turned OFF;
*use appropriate tools and personal protection against electric shock;
*do not use damaged cables, wires and connectors;
*avoid folding the cables and wires;
*do not apply excessive force to the wires by kinking or pressing them too hard: the inner conductors of the cables and wires may get stripped or damaged;
*do not use the power socket with poor contacts to connect;
*do not exceed the load limit parameters specified in the manual;
*the supply conductors wire section is subject to the specifications for current density limit, insulation type and wire material. Light section can result in cable overheating and fire.
When the power is on, NEVER:
*connect/disconnect the connectors;
*open modules and sensors.
</div>

==Overview==

[[File:MEC VIEW.png|300px]]

==Module dimensions==

[[File:MEC DIM.png|500px]]

==Example of connection==

[[File:MEC EXA.png|300px]]

==Module parameters==

{{ Mp
| uartqty = 1
| dts = 1200-115200 b/s
| power = 11.5 … 27.5 V DC from CAN
| maxcur24v = 40 mA
| bustype = CAN (4-wire)
| instalation = DIN-rail (EN 60715)
| maxcablen = 5m
| case = ABS
| protection = IP40
| temprange = -10 … +50 °C
| size = 2U, 36x97x58 mm
| weight = 130g
}}

==Indication of module operation==
{{indicationold}}

==Module installation and connection procedure==
#Install the module in the switchboard on the DIN rail and fix it with the special latch on the module base.
#Connect the UART connector.
#Connect the CAN connector.
#Configure the module using LT setup.
#Check all equipment for proper operation.

==Module shut-off and deinstallation procedure==
#Disconnect the CAN connector.
#Disconnect the UART connector.
#Remove the module from the DIN rail, releasing the latch at the bottom of the module base.

==HW settings==
{|class="wikitable"
|-
!Name!!Type, range!!SUBID!!Default!!Description
|-
|cfg||string||98||9600/8N1||cfg='SPEED/BPS', where
*SPEED – baud rate [1200..115200];
*B – data length [7,8];
*P – presence and type of parity bit [N(No parity),E(Even parity),O(Odd parity)];
*S – stop bit length [1, 1.5 or 2].
Example:
<syntaxhighlight lang="xml" line>
hw="cfg='9600/8N1'"
</syntaxhighlight>
|-
|[Protocol]||string||98||—||Protocol setting is described by protocol parameter. The following
protocols are supported:
*'modbus', Modbus protocol, at the end of redirection the checksum CRC16(Modbus) is added;
*'dmx', DMX protocol;
*'CO2' for connecting Larnitech CO2 sensors;
*'salda' for connecting Salda ventilation.
Example:
<syntaxhighlight lang="xml" line>
hw="cfg='9600/8N1' modbus"
</syntaxhighlight>
|-
|echo||on; off||98||'off'||For settings check out and testing echo parameter can be used. Module
echo-reply can be turned on or off with the help of this parameter.Echo parameter value:
*'off'
*'on'
Example:
<syntaxhighlight lang="xml" line>
hw="cfg='9600/8N1' echo='off'"
</syntaxhighlight>
|}

@@ Line 68: / Line 68: @@
 ==Indication of module operation== <!--T:13-->
-{| class="wikitable"
+{{indicationold|showME=1}}
 ==Module installation and connection procedure== <!--T:14-->

@@ Line 68: / Line 68: @@
 ==Indication of module operation== <!--T:13-->
-{{indicationold}}
+{| class="wikitable"
 ==Module installation and connection procedure== <!--T:14-->

@@ Line 1: / Line 1: @@
 <languages/>
 <translate>
 <!--{{RevisionChanger | hasA = 1 | hasC = 1}}-->
 {{Infobox module
@@ Line 11: / Line 12: @@
 }}
-==AC ADAPTER==
+==AC ADAPTER== <!--T:2-->
 This module is designed for interface adjustment between the AC which have the UART interface (TTL levels) and the Smart Home system.
 <div class="caution">
 CAUTION! All work related to the installation, connection, setting up, service and support must be carried out by qualified personnel with sufficient skills and experience in working with electrical equipment.
@@ Line 31: / Line 34: @@
 </div>
-==Overview==
+==Overview== <!--T:5-->
 [[File:MEC VIEW.png|300px]]
-==Module dimensions==
+==Module dimensions== <!--T:7-->
 [[File:MEC DIM.png|500px]]
-==Example of connection==
+==Example of connection== <!--T:9-->
 [[File:MEC EXA.png|500px]]
-==Module parameters==
+==Module parameters== <!--T:11-->
 {{ Mp
 | uartqty        = 1
@@ Line 60: / Line 67: @@
 }}
-==Indication of module operation==
+==Indication of module operation== <!--T:13-->
 {{indicationold}}
-==Module installation and connection procedure==
+==Module installation and connection procedure== <!--T:14-->
 #Install the module in the switchboard on the DIN rail and fix it with the special latch on the module base.
 #Connect the UART connector.
@@ Line 70: / Line 77: @@
 #Check all equipment for proper operation.
-==Module shut-off and deinstallation procedure==
+==Module shut-off and deinstallation procedure== <!--T:15-->
 #Disconnect the CAN connector.
 #Disconnect the UART connector.
 #Remove the module from the DIN rail, releasing the latch at the bottom of the module base.
-==HW settings==
+==HW settings== <!--T:16-->
 {|class="wikitable"
 |-