DW-RC12.B - Revision history

Support at 08:54, 7 April 2023

2023-04-07T08:54:52Z

2023-03-31T07:46:37Z

2023-03-21T09:11:52Z

2023-03-21T08:34:59Z

2023-03-21T08:32:51Z

2023-03-21T08:32:29Z

2023-03-21T08:30:47Z

2023-03-21T08:28:32Z

2023-03-21T08:27:35Z

2023-03-21T08:26:26Z

@@ Line 199: / Line 199: @@
 <!--T:34-->
-[[File:SensorsCon4.png|200px]]<br>
+[[File:SensorsRC12.png|200px]]<br>
 -wire connection recommended

@@ Line 80: / Line 80: @@
 | maxperch        = 16A
 | power           = 20.0 … 27.5 V DC from CAN
-| maxcur24v       = ??? mA
+| maxcur24v       = 260 mA
 | bustype         = CAN
 | instalation     = DIN rail (EN 60715)

@@ Line 87: / Line 87: @@
 | temprange       = -10 … +50 °C
 | size            = 9U, 156x110x58 mm
-| weight          = ??? g
+| weight          = 400 g
 }}

@@ Line 27: / Line 27: @@
 [[File:DW-RC12.B dwg.png|700px|Fig. 1 Module general view]]
 <br>
 ==Features== <!--T:3-->
@@ Line 115: / Line 100: @@
 for each load.
-==Connection of actuators== <!--T:13-->
+<!--T:13-->
-<!--T:14-->
+<!--T:15-->
 <div class="caution"> Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
 If free (unused) channels remain in a given group after a curtain/jalousie/shutter actuator with low-voltage control or gate actuator has been connected to it, these channels need to be left unused. (Do not connect other devices to them!) </div>
-===Connection of the lights/electric contactor/heating thermal actuator=== <!--T:15-->
+===Connection of the lights/electric contactor/heating thermal actuator=== <!--T:16-->
-<!--T:16-->
+<!--T:17-->
 [[File:lamps.png|200px]]<br>
 Sample HW for this configuration
@@ Line 131: / Line 120: @@
-===Connection of high load device=== <!--T:17-->
+===Connection of high load device=== <!--T:18-->
-<!--T:18-->
+<!--T:19-->
 {| class="wikitable" style="width:800px";
 |-

@@ Line 25: / Line 25: @@
 <!--T:24-->
-[[File:DW-RC12.B dwg.png|700px|frameless|left|Fig. 1 Module general view]]
+[[File:DW-RC12.B dwg.png|700px|Fig. 1 Module general view]]
 <br>

← Older revision		Revision as of 08:30, 21 March 2023
Line 27:		Line 27:
	<div style="clear: both">[[File:DW-RC12.B dwg.png\|700px\|frameless\|left\|Fig. 1 Module general view]]</div>		<div style="clear: both">[[File:DW-RC12.B dwg.png\|700px\|frameless\|left\|Fig. 1 Module general view]]</div>

		+	<br>
	<br>		<br>

@@ Line 27: / Line 27: @@
 <div style="clear: both">[[File:DW-RC12.B dwg.png|700px|frameless|left|Fig. 1 Module general view]]</div>
+<!--T:25-->
-===System installation and assembly===  <!--T:25-->
+===System installation and assembly===
 Before connecting the system, you must:

@@ Line 29: / Line 29: @@
-===System installation and assembly===  <!--T:31-->
+===System installation and assembly===  <!--T:25-->
 Before connecting the system, you must:
-<!--T:32-->
+<!--T:26-->
 *site the sensor and actuators (if not pre-installed), set the sensors and actuators;
 *site the module and power supply.
-<!--T:33-->
+<!--T:27-->
 <div class="cautoin">
-<!--T:35-->
+<!--T:28-->
 Typical diagram of DW-RC12.B module connection is shown in '''fig. 2.'''
 <div style="clear: both">[[File:DW-RC12.B scheme.png|700px|Fig. 2]]</div>