Erich: /* Indication of module operation */

2021-08-09T08:47:15Z

Indication of module operation

Erich: /* Internal layout */

2021-08-09T08:46:35Z

Internal layout

Erich: /* Module dimensions */

2021-08-09T08:46:27Z

Module dimensions

Erich: /* Module dimensions */

2021-08-09T08:46:13Z

Module dimensions

Erich: /* Overview */

2021-08-09T08:46:04Z

Overview

Erich: Created page with "{{RevisionChanger | hasA = 1 | hasB = 1 | hasC = 1}} {{Infobox module | name = DW-RGB03.A | image = DW-RGB03A.png | outCount = 9 | dimmOut = | peakl = 1...."

2021-08-09T08:45:05Z

Created page with "{{RevisionChanger | hasA = 1 | hasB = 1 | hasC = 1}} {{Infobox module | name = DW-RGB03.A | image = DW-RGB03A.png | outCount = 9 | dimmOut = | peakl = 1...."

New page

{{RevisionChanger | hasA = 1 | hasB = 1 | hasC = 1}}
{{Infobox module
| name = DW-RGB03.A
| image = DW-RGB03A.png
| outCount = 9
| dimmOut =
| peakl = 1.67A (20W at 12V)
| peakdl =
| dt =
| inDisc =
| inDigit =
| voltage = 11.5...27.5 V DC
| dim = 2U, 35x102x58 mm
}}

==9-CHANNEL LED CONTROLLER==

The module allows connecting RGB and monochrome LED strips.

==Features==
*Supported load types:
**3x RGB
**2x RGBW + 1 monochrome channels
**1x RGBWW + 1x RGB or 4x monochrome channels

<div class="caution">
CAUTION! All work related to the installation, connection, setting up, service and support must be carried out by qualified personnel with sufficient skills and experience in working with electrical equipment.
To avoid the risk of fire, electric shock, damage to the system and/or personal injury, the system installation and assembly must be performed in accordance with the instructions listed below:
*all connectivity work must be carried out with the power turned OFF;
*use appropriate tools and personal protection against electric shock;
*do not use damaged cables, wires and connectors;
*avoid folding the cables and wires;
*do not apply excessive force to the wires by kinking or pressing them too hard: the inner conductors of the cables and wires may get stripped or damaged;
*do not use the power socket with poor contacts to connect;
*do not exceed the load limit parameters specified in the manual;
*the supply conductors wire section is subject to the specifications for current density limit, insulation type and wire material. Light section can result in cable overheating and fire.
When the power is on, NEVER:
*connect/disconnect the connectors;
*open modules and sensors.
</div>

==Overview==

[[File:RGB03A VIEW.png|500px]]
[[File:RGB03A VIEW2.png|500px]]

==Module dimensions==

[[File:RGB03A DIMM.png|300px]]

==Internal layout==

[[File:RGB03A IL.png|500px]]

==Connection of LED lamps and LED RGB==

[[File:RGB03A EXA.png|500px]]

==Example of connection RGBWW/RGBW LED==

[[File:RGB03A EXA2.png|500px]]

==Example of connection RGB LED with Amp==

[[File:RGB03A EXA3.png|500px]]

==Example of connection load with supply less than 12V==

[[File:RGB03A EXA4.png|500px]]

==Module parameters==

{{ Mp
| outqty = 9
| involtage = 11.5...25V DC
| currtype = DC
| adjtype = PWM
| maxperch = 3A (36W at 12V)
| maxperdev = 15A (180W at 12V)
| power = 11.5 … 27.5 V DC from CAN
| maxcur24v = 55 mA
| bustype = CAN (4-wire)
| instalation = DIN-rail (EN 60715)
| case = ABS
| protection = IP40
| temprange = -10 … +50 °C
| size = 2U, 35x102x58 mm
| weight = 85 g
}}

==Indication of module operation==
===Bootloader===
{{indication| textBBB= Waiting for bootloader command}}
===Firmware===
{{indicationfw
|err1 = 1
|err2 = 1
}}

==Module installation and connection procedure==
#Install the module in the switchboard on the DIN rail and fix it with the special latch on the module base.
#Connect the CAN connector.
#Connect the X1, X2, X3 connectors.
#Configure the module using LT setup.
#Apply power to the load.
#Check all equipment for proper operation.

==Module shut-off and deinstallation procedure==
#Disconnect the power from the load.
#Disconnect the X1, X2, X3 connectors.
#Disconnect the CAN connector.
#Remove the module from the DIN rail, releasing the latch at the bottom of the module base.

==HW settings==
{|class="wikitable"
|-
!Name!!Type, range!!SUBID!!Default!!Description
|-
|dm||char[9]||98||'RGBRGBRGB'||Each char is responsible for the type of a particular channel, RGB takes 3 channels
*'D' – use like dimer-lamp
*'RGB' – Use like RGB lamp
Example: dm='DDDRGBDDD'
|-
|def||integer 0-250||1-9||100||The default brightness level in case of a power reset (1..250). Example: def=250
|-
|min||integer 0-100||1-9||0||Minimum dimming level, example: min=10
|-
|max||integer 0-100||1-9||100||Maximum dimming level, example max=95
|-
|runtime||integer 0-100||1-9||5||Runtime is the speed of changing the brightness(measured in seconds). Example: runtime=20
|-
|f||double 0.5-24000||98||500||It is frequency (measured in Hz); Example: f=500
|}

<syntaxhighlight lang="xml" line>
<item addr="555:1" auto-period="600" cfgid="66" name="Dimmer" type="dimer-lamp" uniq_id="4054"/>
<item addr="555:2" auto-period="600" cfgid="66" name="Dimmer" type="dimer-lamp" uniq_id="4055"/>
<item addr="555:3" auto-period="600" cfgid="66" name="Dimmer" type="dimer-lamp" uniq_id="4056"/>
<item addr="555:4" auto-period="600" cfgid="66" name="RGB" type="rgb-lamp" uniq_id="4053"/>
<item addr="555:7" auto-period="600" cfgid="66" name="Dimmer" type="dimer-lamp" uniq_id="4057"/>
<item addr="555:8" auto-period="600" cfgid="66" name="Dimmer" type="dimer-lamp" uniq_id="4058"/>
<item addr="555:9" auto-period="600" cfgid="66" name="Dimmer" type="dimer-lamp" uniq_id="4059"/>
<item addr="555:97" cfgid="66" name="Temperature" system="yes" type="temperature-sensor" uniq_id="4010"/>
<item addr="555:98" cfgid="66" hw="dm='DDDRGBDDD'" name="Temperature" system="yes" type="temperature-sensor" uniq_id="4011"/>
</syntaxhighlight>

@@ Line 47: / Line 47: @@
 ==Module dimensions==
-[[File:RGB03A DIM.png|300px]]
+[[File:RGB03A DIM.png|500px]]
 ==Internal layout==

@@ Line 90: / Line 90: @@
 ==Indication of module operation==
-===Bootloader===
+{{indicationold}}
 ==Module installation and connection procedure==

@@ Line 51: / Line 51: @@
 ==Internal layout==
-[[File:RGB03A IL.png|500px]]
+[[File:RGB03A IL.png|300px]]
 ==Connection of LED lamps and LED RGB==

@@ Line 42: / Line 42: @@
 ==Overview==
-[[File:RGB03A VIEW.png|500px]]
+[[File:RGB03A VIEW.jpg|500px]]
-[[File:RGB03A VIEW2.png|500px]]
+[[File:RGB03A VIEW2.png|500px|style="clear:left"]]
 ==Module dimensions==

DW-RGB03.A - Revision history

Erich: /* Indication of module operation */

Erich: /* Internal layout */

Erich: /* Module dimensions */

Erich: /* Module dimensions */

Erich: /* Overview */

Erich: Created page with "{{RevisionChanger | hasA = 1 | hasB = 1 | hasC = 1}} {{Infobox module | name = DW-RGB03.A | image = DW-RGB03A.png | outCount = 9 | dimmOut = | peakl = 1...."