DW-SW16 - Revision history

Rusanov: Marked this version for translation

2022-01-06T14:30:57Z

Marked this version for translation

Rusanov at 14:30, 6 January 2022

2022-01-06T14:30:39Z

Erich: /* 16-CHANNEL ADAPTER FOR BUTTONS */

2021-12-21T14:50:44Z

16-CHANNEL ADAPTER FOR BUTTONS

Erich at 08:12, 11 August 2021

2021-08-11T08:12:22Z

Erich: /* Connection of buttons/LED buttons */

2021-08-11T07:06:34Z

Connection of buttons/LED buttons

Erich: /* Led button scheme */

2021-08-11T06:59:34Z

Led button scheme

Erich: /* Connector */

2021-08-11T06:59:14Z

Connector

Erich: Created page with "{{RevisionChanger | hasA = 1 | hasB = 1 | hasC = 1}} {{Infobox module | name = DW-SW16.C | image = DW-SW16C.png | outCount = | dimmOut = | peakl = | pe..."

2021-08-11T06:58:35Z

Created page with "{{RevisionChanger | hasA = 1 | hasB = 1 | hasC = 1}} {{Infobox module | name = DW-SW16.C | image = DW-SW16C.png | outCount = | dimmOut = | peakl = | pe..."

New page

{{RevisionChanger | hasA = 1 | hasB = 1 | hasC = 1}}
{{Infobox module
| name = DW-SW16.C
| image = DW-SW16C.png
| outCount =
| dimmOut =
| peakl =
| peakdl =
| dt =
| inCount = 16
| inB = 15
| inLB = 8
| inDry =
| voltage = 11.5...27.5 V DC
| dim = 2U, 36x102x58 mm
}}

==16-CHANNEL ADAPTER FOR BUTTONS==

This module can support up to 15 buttons/reed switches or 8 LED buttons.

<div class="caution">
CAUTION! All work related to the installation, connection, setting up, service and support must be carried out by qualified personnel with sufficient skills and experience in working with electrical equipment.
To avoid the risk of fire, electric shock, damage to the system and/or personal injury, the system installation and assembly must be performed in accordance with the instructions listed below:
*all connectivity work must be carried out with the power turned OFF;
*use appropriate tools and personal protection against electric shock;
*do not use damaged cables, wires and connectors;
*avoid folding the cables and wires;
*do not apply excessive force to the wires by kinking or pressing them too hard: the inner conductors of the cables and wires may get stripped or damaged;
*do not use the power socket with poor contacts to connect;
*do not exceed the load limit parameters specified in the manual;
*the supply conductors wire section is subject to the specifications for current density limit, insulation type and wire material. Light section can result in cable overheating and fire.
When the power is on, NEVER:
*connect/disconnect the connectors;
*open modules and sensors.
</div>

==Overview==

[[File:SW16C VIEW.png|300px]]

==Module dimensions==

[[File:SW16C DIM.png|500px]]

==Connector==

[[File:WL02C CONN.png|300px]]

==Led button scheme==

[[File:WL02C LED.png|200px]]

==Connection of buttons/LED buttons==

[[File:WL02C EXA.png|500px]]

==Module parameters==

{{ Mp
| inqty = 16
| buttons = 15
| ledbuttons = 8
| blvoltage = 3V
| power = 11.5 … 27.5 V DC from CAN
| maxcur24v = 45 mA
| buttonreclen = 30m
| bustype = CAN (4-wire)
| instalation = DIN-rail (EN 60715)
| case = ABS
| protection = IP40
| temprange = -10 … +50 °C
| size = 2U, 36x102x58 mm
| weight = 75g
}}

==Indication of module operation==
===Bootloader===
{{indication| textBBB= Waiting for bootloader command}}
===Firmware===
{{indicationfw
|err1 = 1
|err5 = 1
|canact = 1
|canacttxt = Key pressed
}}

==Module installation and connection procedure==
#Install the module in the switchboard on the DIN rail and fix it with the special latch on the module base.
#Connect the CAN connector.
#Connect the X1 connector.
#Configure the module using LT setup.
#Apply power to the load.
#Check all equipment for proper operation.

==Module shut-off and deinstallation procedure==
#Disconnect the power from the load.
#Disconnect the X1 connector.
#Disconnect the CAN connector.
#Remove the module from the DIN rail, releasing the latch at the bottom of the module base.

==HW settings==
{|class="wikitable"
|-
!Name!!Type, range!!SUBID!!Default!!Description
|-
|in||char[16]||98||'BBBBBBBBGGGGGGGG'||Each char is responsible for the type of a particular channel
*'B'-Button, button of bell a type;
*'C'-Inverted button, inverse button of a bell type (for normally-closed);
*'D'-Backlit button, illuminated button;
*'E'-Inverted backlit button, inverse illuminated button;
*'S'-Switch, fixed switch;
*'K'-Contact, reed contact;
*'H'-Inverted contact, invers reed contact;
*'G'-GND, is used as earthing;
*'-'-none, nothing is connected.
Example: in='DEHHHHBB- -CCSSSG'
|}
<syntaxhighlight lang="xml" line>
<item addr="441:11" cfgid="55" name="Switch" type="switch" uniq_id="4628"/>
<item addr="441:12" cfgid="55" name="Switch" type="switch" uniq_id="4629"/>
<item addr="441:13" cfgid="55" name="Switch" type="switch" uniq_id="4630"/>
<item addr="441:14" cfgid="55" name="Switch" type="switch" uniq_id="4631"/>
<item addr="441:15" cfgid="55" name="Switch" type="switch" uniq_id="4632"/>
<item addr="441:16" cfgid="55" name="Switch" type="switch" uniq_id="4633"/>
<item addr="441:17" cfgid="55" name="Switch" type="switch" uniq_id="4634"/>
<item addr="441:18" cfgid="55" name="Door" type="door-sensor" uniq_id="4637"/>
<item addr="441:19" cfgid="55" name="Switch" type="switch" uniq_id="4638"/>
<item addr="441:20" cfgid="55" name="Switch" type="switch" uniq_id="4639"/>
<item addr="441:25" cfgid="55" name="Switch" type="switch" uniq_id="4640"/>
<item addr="441:98" cfgid="55" hw="in='BBDDEESHBB----BG'" name="Temperature" system="yes" type="temperature-sensor" uniq_id="4636"/>
</syntaxhighlight>

@@ Line 1: / Line 1: @@
 <languages/>
 <translate>
 {{RevisionChanger | hasA = 1 | hasB = 1 | hasC = 1}}
 {{Infobox module
@@ Line 18: / Line 19: @@
 }}
-==16-CHANNEL ADAPTER FOR BUTTONS==
+==16-CHANNEL ADAPTER FOR BUTTONS== <!--T:2-->
 This module can support up to 15 buttons/reed switches or 8 LED buttons.
-==Features==
+==Features== <!--T:4-->
 *Up to 15 buttons/reed switches
 *Up to 8 LED buttons
@@ Line 28: / Line 30: @@
 *Line noise protection
 <div class="caution">
 CAUTION! All work related to the installation, connection, setting up, service and support must be carried out by qualified personnel with sufficient skills and experience in working with electrical equipment.
@@ Line 44: / Line 47: @@
 </div>
-==Overview==
+==Overview== <!--T:6-->
 [[File:SW16C VIEW.png|300px]]
-==Module dimensions==
+==Module dimensions== <!--T:8-->
 [[File:SW16C DIM.png|500px]]
-==Connector==
+==Connector== <!--T:10-->
 [[File:SW16C CONN.png|300px]]
-==Led button scheme==
+==Led button scheme== <!--T:12-->
 [[File:SW16C LED.jpg|200px]]
-==Connection of buttons/LED buttons==
+==Connection of buttons/LED buttons== <!--T:14-->
 [[File:SW16C EXA.png|500px]]
-==Module parameters==
+==Module parameters== <!--T:16-->
 {{ Mp
 | inqty           = 16
@@ Line 83: / Line 92: @@
 }}
-==Indication of module operation==
+==Indication of module operation== <!--T:18-->
 ===Bootloader===
 {{indication| textBBB= Waiting for bootloader command}}
@@ Line 94: / Line 103: @@
 }}
-==Module installation and connection procedure==
+==Module installation and connection procedure== <!--T:19-->
 #Install the module in the switchboard on the DIN rail and fix it with the special latch on the module base.
 #Connect the X1 connector.
@@ Line 101: / Line 110: @@
 #Check all equipment for proper operation.
-==Module shut-off and deinstallation procedure==
+==Module shut-off and deinstallation procedure== <!--T:20-->
 #Disconnect the CAN connector.
 #Disconnect the X1 connector.
 #Remove the module from the DIN rail, releasing the latch at the bottom of the module base.
-==HW settings==
+==HW settings== <!--T:21-->
 {|class="wikitable"
 |-

← Older revision		Revision as of 14:50, 21 December 2021
Line 19:		Line 19:

	This module can support up to 15 buttons/reed switches or 8 LED buttons.		This module can support up to 15 buttons/reed switches or 8 LED buttons.
		+
		+	==Features==
		+	*Up to 15 buttons/reed switches
		+	*Up to 8 LED buttons
		+	*Supports single/double/triple/long click.<br>Up to 4 different actions for each button
		+	*Line noise protection

	<div class="caution">		<div class="caution">