Metaforsa2 MF-14 - Revision history

Support: Minor edit

2024-02-28T11:00:31Z

Minor edit

2024-02-08T14:50:13Z

Marked this version for translation

2024-02-08T14:46:43Z

Minor edit

2023-09-22T14:36:42Z

2023-08-17T11:34:38Z

2023-05-30T07:11:37Z

2022-02-16T12:46:38Z

2022-02-04T12:27:22Z

2022-02-04T11:56:17Z

2022-02-04T11:55:21Z

@@ Line 110: / Line 110: @@
 |  Socket connectors ||  Magnetic reed switches
 |-
-|  Underfloor heating ||  Magnetic reed switches
+|  Underfloor heating ||  Motion sensors
 |-
 |  Curtain/gate actuators ||  Leakage sensors

@@ Line 325: / Line 325: @@
 {{indicationmfold}}
-===System installation and assembly===  <!--T:31-->
+===System installation and assembly=== <!--T:31-->
 Before connecting the system, you must:

@@ Line 319: / Line 319: @@
 |[[File:OW.png|80px|frameless]] ||OneWire|| Digital sensors connection (temperature)<br>VCC — sensors power supply output +5V<br>OW1-OW4 — OneWire data buses<br>GND — common
 |-
-|[[File:Can.jpg|80px|frameless]] ||VCC<br>GND<br>L<br>H|| External modules connection for CAN-bus<br>VСС — 12V output for external devices power supply<br>GND — common<br>L — CAN-L data bus<br>H — CAN-H data bus
+|[[File:Can.jpg|80px|frameless]] ||VCC<br>GND<br>L<br>H|| External modules connection for CAN-bus<br>VСС — 24V output for external devices power supply<br>GND — common<br>L — CAN-L data bus<br>H — CAN-H data bus
 |}

@@ Line 25: / Line 25: @@
 While working with the system, you must strictly comply with all the requirements set out in this manual. Failure to comply may result in damage to the device, its failure, electric shock, fire and other fallout.
 The manufacturer reserves the right to make changes to this manual without prior notice. This manual is an integral part of the system and shall remain with the end-use customer.
 ==Features== <!--T:4-->

@@ Line 257: / Line 257: @@
 {| class="wikitable" style="clear:left;"
 |-
-|1 || — connector for load application and power supply
+|1 || — connector for load application
 |-
 |2 || — connector for dimming-lamps application
@@ Line 321: / Line 321: @@
 <!--T:30-->
 {{indicationmfold}}
 ===System installation and assembly===  <!--T:31-->

@@ Line 184: / Line 184: @@
 |-
 | Dimmer type || MOSFET
 |-
 | Dimming type || trailing edge

@@ Line 207: / Line 207: @@
 |Permissible humidity || 0 … 95% (non-condensing)
 |-
-|Power supply || 23 … 27.5 V DC<br>24V, 0.75A Recommended
+|Power supply || 12 … 27.5 V DC<br>24V, 0.75A Recommended
 |-
 |Maximum demand || 0.5А

@@ Line 666: / Line 666: @@
 Example: in='MMMMMMMMMMMMLLLLLLLLLLLL'
 motion sensors and 12 leak-sensors;
-in='BBBBBBBBSSSSSSRRRRSSRRRR'
+in='BBBBBBBBSSSSSSBBBBSSSSSS'
-buttons; 8 switches and 8 LED channels.
+buttons; 12 switches.
 |}

@@ Line 472: / Line 472: @@
 <!--T:61-->
-Buttons and reed switches are connected to any free input in1-in16, while their second contact point is connected to GND point of the relevant METAFORSA module group, + 12V power outputs – not in use. The example of connection is shown in '''Fig. 14-15'''.
+Buttons and reed switches are connected to any free input in1-in24, while their second contact point is connected to GND point of the relevant METAFORSA module group, + 12V power outputs – not in use. The example of connection is shown in '''Fig. 14-15'''.
 {| style="width"700px"
 |- style="tezt-align:center;"