Metaforsa 3/3.plus - Revision history

Support: Added Youtube

2024-06-11T13:03:30Z

Added Youtube

Support: Add HW table

2024-04-05T12:51:44Z

Add HW table

Support: Minor edit

2024-04-03T13:25:26Z

Minor edit

Support: Marked this version for translation

2024-03-13T10:11:56Z

Marked this version for translation

Support: Minor updates

2024-03-13T10:06:42Z

Minor updates

Support: Minor updates

2024-03-13T10:06:00Z

Minor updates

Support: Minor edit

2024-02-13T15:34:27Z

Minor edit

Support: Added a RS485 information to table

2024-02-09T09:43:19Z

Added a RS485 information to table

Support: Update table

2024-02-08T07:29:28Z

Update table

Support at 13:17, 6 February 2024

2024-02-06T13:17:22Z

@@ Line 24: / Line 24: @@
 While working with the system, you must strictly comply with all the requirements set out in this manual. Failure to comply may result in damage to the device, its failure, electric shock, fire and other fallout.
 The manufacturer reserves the right to make changes to this manual without prior notice. This manual is an integral part of the system and shall remain with the end-use customer.
 ==Features== <!--T:4-->

@@ Line 659: / Line 659: @@
 *'r' - thermo-resistor
 *'t' - DALLAS
 *'-' - none
 Example: io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'
 |-
 |colspan="3"|'''Only for Metaforsa 3.plus'''

@@ Line 432: / Line 432: @@
 <!--T:92-->
-The motion sensors/leakage sensors should be connected to any free input in1-in28; in these conditions their power is connected to the contact points of +12V and GND of the relevant group. The example of connection is shown in '''Fig.11'''.
+The motion sensors/leakage sensors should be connected to any free input in1-in28; in these conditions their power is connected to the contact points of +5V and GND of the relevant group. The example of connection is shown in '''Fig.11'''.
 <!--T:55-->

@@ Line 233: / Line 233: @@
 <nowiki>*</nowiki> – Output channels should only be connected using amplifier which uses 5V PWM signal from IO output as input
 <nowiki>**</nowiki> – installing additional power supply units is required for long lines; the maximum length of the line may be reduced by various interference factors
 <nowiki>***</nowiki> – Only for Metaforsa 3.plus
@@ Line 283: / Line 285: @@
 *connector (7) — expansion module connection.
 The physical configuration and contact point assignment of each connector are shown in '''table 2'''.
@@ Line 309: / Line 312: @@
 {{indicationmfold}}
-===System installation and assembly===  <!--T:31-->
+===System installation and assembly=== <!--T:31-->
 Before connecting the system, you must:
@@ Line 428: / Line 431: @@
 ====Connection of motion sensors/leakage sensors==== <!--T:54-->
 The motion sensors/leakage sensors should be connected to any free input in1-in28; in these conditions their power is connected to the contact points of +12V and GND of the relevant group. The example of connection is shown in '''Fig.11'''.
@@ Line 438: / Line 442: @@
 ====Connection of buttons/switches/magnetic reed switches==== <!--T:56-->
 Buttons and reed switches are connected to any free input in1-in28, while their second contact point is connected to GND point of the relevant METAFORSA module group. The example of connection is shown in '''Fig. 12-13'''.
@@ Line 640: / Line 645: @@
 *'z' - WS2812B -string
 *'e' - led-button inverse
 *'d' - led-button
@@ Line 654: / Line 660: @@
 *'t' - DALLAS
 *'-' - none
 Example: io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'

@@ Line 303: / Line 303: @@
 |[[File:IOC_CONN.png|80px|frameless]] ||In1-14, In15-28 GND|| Controlling devices connection (buttons, LED buttons, magnetic reed switches, motion detectors, leakage sensors, temperature sensors, etc.): <br>In1 … In28 — logic inputs <br>GND — common
 |-
-|[[File:Can.jpg|80px|frameless]] ||VCC<br>GND<br>L<br>H|| External modules connection for CAN-bus<br>VСС — 12V output for external devices power supply<br>GND — common<br>L — CAN-L data bus<br>H — CAN-H data bus
+|[[File:Can.jpg|80px|frameless]] ||VCC<br>GND<br>L<br>H|| External modules connection for CAN-bus<br>VСС — 24V output for external devices power supply<br>GND — common<br>L — CAN-L data bus<br>H — CAN-H data bus
 |}

@@ Line 142: / Line 142: @@
 |-
 | Power supply cord || 1 pc
 |}

@@ Line 133: / Line 133: @@
 | Motion sensor CW-MSD || 3 pcs
 |-
-| Leakage sensor FW-WL.A || 2 pcs
+| Leakage sensor FW-WL.B || 2 pcs
 |-
-| Temperature-sensitive element FW-TS.A || 4 pcs
+| Temperature-sensitive element FW-TS || 4 pcs
 |-
 | Magnetic reed switch (window/door position sensor) || 4 pcs

@@ Line 217: / Line 217: @@
 |LAN wire type || UTP/FTP Cat 5E
 |-
 |LAN connection type || Connector RJ-45
 |-
 |Dimensional specifications || 9U, 156x90x58 mm
@@ Line 232: / Line 236: @@
 <nowiki>**</nowiki> – installing additional power supply units is required for long lines; the maximum length of the line may be reduced by various interference factors
 ===General structure of the System=== <!--T:22-->

@@ Line 105: / Line 105: @@
 |  Gate actuators || Temperature sensors
 |-
-|  Water supply || LED strips
+|  Water supply || LED strips/3-4-5 channel RGB strips/WS2812B strips
 |-
-|  Heating valves || 3-4-5 channel RGB strips
+|  Heating valves || RS485 devices*
 |}
 <nowiki>*</nowiki> – Only for Metaforsa 3.plus

@@ Line 657: / Line 657: @@
 Example: io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'
 |-
-|colspan="2"|'''Only for Metaforsa 3.plus'''
+|colspan="3"|'''Only for Metaforsa 3.plus'''
 |-
 |cfg||string||98||9600/8N1||cfg='SPEED/BPS', where