FuzzyBot: Importing a new version from external source

2024-04-05T12:53:46Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2024-03-13T10:11:58Z

Importing a new version from external source

New page

*'e' - led-button inverse
*'d' - led-button
*'c' - button inverse
*'b' - button
*'s' - switch
*'k' - contact inverse
*'h' - contact
*'l' - leak
*'n' - Neptun
*'v' - motion inverse
*'m' - motion
*'r' - thermo-resistor
*'t' - DALLAS

← Older revision		Revision as of 12:53, 5 April 2024
Line 12:		Line 12:
	*'r' - thermo-resistor		*'r' - thermo-resistor
	*'t' - DALLAS		*'t' - DALLAS
		+	*'-' - none
		+	Example: io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'
		+	\|-
		+	\|hw\|\|string\|\|98\|\|-\|\|hw="...", where
		+	*pwm_invert – PWM inverting [1, 0];
		+	*lbn_bright – brightness of led buttons, range (0 - 255);
		+	*f – by default PWM frequency is 1000, range (1 - 5000).
		+	Example:
		+	<syntaxhighlight lang="xml" line>
		+	hw="io='4---zdd----t--' pwm_invert=1 lbn_bright=255 f=1000"
		+	</syntaxhighlight>
		+	\|-
		+	\|colspan="3"\|'''Only for Metaforsa 3.plus'''
		+	\|-
		+	\|cfg\|\|string\|\|98\|\|9600/8N1\|\|cfg='SPEED/BPS', where
		+	*SPEED – baud rate [1200..115200];
		+	*B – data length [7,8];
		+	*P – presence and type of parity bit [N(No parity),E(Even parity),O(Odd parity)];
		+	*S – stop bit length [1, 1.5 or 2].
		+	Example:
		+	<syntaxhighlight lang="xml" line>
		+	hw="cfg='9600/8N1'"
		+	</syntaxhighlight>
		+	\|-
		+	\|[Protocol]\|\|string\|\|98\|\|—\|\|Protocol setting is described by protocol parameter. The following
		+	protocols are supported:
		+	*'modbus', Modbus protocol, at the end of redirection the checksum CRC16(Modbus) is added;
		+	*'dmx', DMX protocol;
		+	*'CO2' for connecting Larnitech CO2 sensors;
		+	*'salda' for connecting Salda ventilation.
		+	Example:
		+	<syntaxhighlight lang="xml" line>
		+	hw="cfg='9600/8N1' modbus"
		+	</syntaxhighlight>
		+	\|-
		+	\|echo\|\|on; off\|\|98\|\|'off'\|\|For settings check out and testing echo parameter can be used. Module
		+	echo-reply can be turned on or off with the help of this parameter.Echo parameter value:
		+	*'off'
		+	*'on'
		+	Example:
		+	<syntaxhighlight lang="xml" line>
		+	hw="cfg='9600/8N1' echo='off'"
		+	</syntaxhighlight>
		+	\|}

Translations:Metaforsa 3/3.plus/94/en - Revision history

FuzzyBot: Importing a new version from external source

FuzzyBot: Importing a new version from external source