Difference between revisions of "Translations:Metaforsa 3/3.plus/87/bs"

Latest revision as of 08:09, 8 April 2024

Information about message (contribute)

This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.

Message definition (Metaforsa 3/3.plus)

==HW Settings==
{| class="wikitable"
|-
!Name!!Type, range!!SUBID!!Default!!Description
|-
|runtime||integer 0-100 || 1-10 || 15 ||runtime is the open/close time in seconds, is used for jalousie, gate, valve(2 pole);
<br>Example: runtime=15
|-
|runtimeopen||integer 0-60000||Blinds subId || ||Runtimeopen is the open time in milliseconds, is used for blinds; Example: runtimeopen=15000
|-
|runtimeclose||integer 0-60000||Blinds subId|| ||Runtimeclose is the close time in milliseconds, is used for blinds; Example: runtimeclose=15000
|-
|hold||integer 0-10000||1-10||500||hold is the bridging time in milliseconds, is used for gate and jalousie (by default hold is the same as runtime for jalousie and gate), lock; Example: hold=3500
|-
|def||string 'ON'||1-10||'OFF'||def is the element status is set after restart, is used for lamp, heating, valve(1 pole); Example: def='ON'
|-
|stop||Char ‘R’||1-7||–||(for 2-pole gate and blinds) If it is declared then by Stop command during the motion, the same impulse appears as it was at the beginning of the motion. Pole, an which the stop-impules is formed, is defined by the parameter Stop value. If it is ‘r’ or ‘R’ then stop-impulse is produced on the opposite to the start-impulse pole. If any other value is delcared (e.g., ‘d’ ) then the stop-impulse is on the same pole. If a Runtime passed after the beginning of the motion then the stop-impulse is not formed. Example: stop=’r’
|-
|out||char[10]||98||'LLLLHHHHP-'||Each char is responsible for the type of a particular channel
*'L'-Lamp;
*'M'-Lamp Inverse;
*'J'-Heating NO, valve-heating, normally open;
*'H'-Heating NC, valve-heating, normally closed;
*'B'-Blinds (2 pole), jalousie/curtains;
*'C'-Blinds Inverse (2 pole), jalousie/curtains, invert open-close;
*'G'-Gate (2 pole), 2 pole gate;
*'D'-Gate (2 pole) Inverse, 2 pole gate, invert open-close;
*'X'-Gate (1 pole /short press), 1 pole gate;
*'Z'-Gate (1 pole) Inverse, 1 pole gate, invert open-close;
*'V'-Valve (2 pole), 2 pole valve;
*'W'-Valve (2 pole) Inverse, 2 pole valve, invert open-close;
*'R'-Valve (1 pole), 1 pole valve,;
*'S'-Valve (1 pole) Inverse, 1 pole valve, invert open-close;
*'K'-Lock (short press);
*'N'-Lock (short press) Inverse;
*'P'-Blinds (2 pole);
*'O'-Blinds Inverse (2 pole), invert open-close;
*'F'-FanCoil. Group1 (Lamp Toggle). For fancoil speed control;
*'E'-FanCoil. Group2 (Lamp Toggle). For fancoil speed control;
*'Q'-FanCoil. Group3 (Lamp Toggle). For fancoil speed control;
*'U'-FanCoil. Group4 (Lamp Toggle). For fancoil speed control;
*'I'-FanCoil. Group5 (Lamp Toggle). For fancoil speed control;
*'-'-none, nothing is connected.
Example: out='LLB-G-V-W-'
|-
|dm||char[4]||98||‘LLLL’||Each char is responsible for the type of a particular channel
*‘g’ – use like halogen dimer-lamp
*‘s’ – Soft Switch, lamp, when on/off power is supplied/deenergised smoothly (500msec)
*‘k’ – Switch, lamp, when on/off power is supplied/deenergised immediately
*‘l’ – LED Function, dimmable LED lamps
*‘v’ – linear Function of dimming
*‘-‘ – Channel disabled
*‘+’ – Regular channel
Example: dm=’skl-‘
|-
|def||integer 0-250||11-14||100||The default brightness level in case of a power reset (1..250). Example: def=250
|-
|min||integer 0-100||11-14||0||Minimum dimming level, example: min=10
|-
|max||integer 0-100||11-14||100||Maximum dimming level, example max=95
|-
|start||integer 0-100||11-14||0||The Start function is used for lamps that lack the minimal voltage to get turned on. If the set value is lower than the start value, the lamp is turned on at the start value and them the light is dimmed down to the set level. Example: start=60
|-
|force||integer 0-100||11-14||10||Time duration of the starting value (measured in milliseconds). Example: force=20
|-
|runtime||integer 0-60000||11-14||1000||Runtime is the speed of changing the brightness from ‘min’ to ‘max’ (measured in milliseconds). Example: runtime=1000
|-
|offset||integer (+/- 0…39)||39-46||'0'||sensor values offset; For example, offset is -3.8 :
Example: hw="offset='-3.8'"
|-
|io||char[28]||98||io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'||Each char is responsible for the type of a particular channel
*'0' - led-dimmer
*'1' - halogen-dimmer
*'2' - linear-dimmer
*'3'..'6' - RGB-3..6 channels
*'z' - WS2812B -string

==HW Settings==
{| class="wikitable"
|-
!Name!!Type, range!!SUBID!!Default!!Description
|-
|runtime||integer 0-100 || 1-10 || 15 ||runtime is the open/close time in seconds, is used for jalousie, gate, valve(2 pole); 
<br>Example: runtime=15
|-
|runtimeopen||integer 0-60000||Blinds subId || ||Runtimeopen is the open time in milliseconds, is used for blinds; Example: runtimeopen=15000
|-
|runtimeclose||integer 0-60000||Blinds subId|| ||Runtimeclose is the close time in milliseconds, is used for blinds; Example: runtimeclose=15000
|-
|hold||integer 0-10000||1-10||500||hold is the bridging time in milliseconds, is used for gate and jalousie (by default hold is the same as runtime for jalousie and gate), lock; Example: hold=3500
|-
|def||string 'ON'||1-10||'OFF'||def is the element status is set after restart, is used for lamp, heating, valve(1 pole); Example: def='ON'
|-
|stop||Char ‘R’||1-7||–||(for 2-pole gate and blinds) If it is declared then by Stop command during the motion, the same impulse appears as it was at the beginning of the motion. Pole, an which the stop-impules is formed, is defined by the parameter Stop value. If it is ‘r’ or ‘R’ then stop-impulse is produced on the opposite to the start-impulse pole. If any other value is delcared (e.g., ‘d’ ) then the stop-impulse is on the same pole. If a Runtime passed after the beginning of the motion then the stop-impulse is not formed. Example: stop=’r’
|-
|out||char[10]||98||'LLLLHHHHP-'||Each char is responsible for the type of a particular channel
*'L'-Lamp;
*'M'-Lamp Inverse;
*'J'-Heating NO, valve-heating, normally open;
*'H'-Heating NC, valve-heating, normally closed;
*'B'-Blinds (2 pole), jalousie/curtains;
*'C'-Blinds Inverse (2 pole), jalousie/curtains, invert open-close;
*'G'-Gate (2 pole), 2 pole gate;
*'D'-Gate (2 pole) Inverse, 2 pole gate, invert open-close;
*'X'-Gate (1 pole /short press), 1 pole gate;
*'Z'-Gate (1 pole) Inverse, 1 pole gate, invert open-close;
*'V'-Valve (2 pole), 2 pole valve;
*'W'-Valve (2 pole) Inverse, 2 pole valve, invert open-close;
*'R'-Valve (1 pole), 1 pole valve,;
*'S'-Valve (1 pole) Inverse, 1 pole valve, invert open-close;
*'K'-Lock (short press);
*'N'-Lock (short press) Inverse;
*'P'-Blinds (2 pole);
*'O'-Blinds Inverse (2 pole), invert open-close;
*'F'-FanCoil. Group1 (Lamp Toggle). For fancoil speed control;
*'E'-FanCoil. Group2 (Lamp Toggle). For fancoil speed control;
*'Q'-FanCoil. Group3 (Lamp Toggle). For fancoil speed control;
*'U'-FanCoil. Group4 (Lamp Toggle). For fancoil speed control;
*'I'-FanCoil. Group5 (Lamp Toggle). For fancoil speed control;
*'-'-none, nothing is connected.
Example: out='LLB-G-V-W-'
|-
|dm||char[4]||98||‘LLLL’||Each char is responsible for the type of a particular channel
*‘g’ – use like halogen dimer-lamp
*‘s’ – Soft Switch, lamp, when on/off power is supplied/deenergised smoothly (500msec)
*‘k’ – Switch, lamp, when on/off power is supplied/deenergised immediately
*‘l’ – LED Function, dimmable LED lamps
*‘v’ – linear Function of dimming
*‘-‘ – Channel disabled
*‘+’ – Regular channel
Example: dm=’skl-‘
|-
|def||integer 0-250||11-14||100||The default brightness level in case of a power reset (1..250). Example: def=250
|-
|min||integer 0-100||11-14||0||Minimum dimming level, example: min=10
|-
|max||integer 0-100||11-14||100||Maximum dimming level, example max=95
|-
|start||integer 0-100||11-14||0||The Start function is used for lamps that lack the minimal voltage to get turned on. If the set value is lower than the start value, the lamp is turned on at the start value and them the light is dimmed down to the set level. Example: start=60
|-
|force||integer 0-100||11-14||10||Time duration of the starting value (measured in milliseconds). Example: force=20
|-
|runtime||integer 0-60000||11-14||1000||Runtime is the speed of changing the brightness from ‘min’ to ‘max’ (measured in milliseconds). Example: runtime=1000
|-
|offset||integer (+/- 0…39)||39-46||'0'||sensor values offset; For example, offset is -3.8 :
Example: hw="offset='-3.8'"
|-
|io||char[28]||98||io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'||Each char is responsible for the type of a particular channel
*'0' - led-dimmer
*'1' - halogen-dimmer
*'2' - linear-dimmer
*'3'..'6' - RGB-3..6 channels
*'z' - WS2812B -string

Translation==HW Postavke==
{| class="wikitable"
|-
!Ime!!Vrsta, opseg!!SUBID!!Podrazumevano!!Opis
|-
|runtime||integer 0-100 || 1-10 || 15 ||vrijeme rada je vrijeme otvaranja/zatvaranja u sekundama, koristi se za žaluziju, kapiju, ventil (2 polni);
<br>Primjer: runtime=15
|-
|runtimeopen||integer 0-60000||Blinds subId || ||Runtimeopen je otvoreno vrijeme u milisekundama, koristi se za roletne; primjer: runtimeopen=15000
|-
|runtimeclose||integer 0-60000||Blinds subId|| ||Runtimeclose je vrijeme zatvaranja u milisekundama, koristi se za roletne; primjer: runtimeclose=15000
|-
|hold||integer 0-10000||1-10||500||hold je vrijeme premošćavanja u milisekundama, koristi se za kapiju i žaluziju (podrazumevano zadržavanje je isto kao vrijeme izvođenja za žaluziju i vrata), zaključavanje; primjer: hold=3500
|-
|def||string 'ON'||1-10||'OFF'||def je status elementa postavljen nakon ponovnog pokretanja, koristi se za lampu, grijanje, ventil (1 pol); primjer: def='ON'
|-
|stop||Char ‘R’||1-7||–||(za 2-polne kapije i roletne) Ako se deklariše tada komandom Stop tokom kretanja, pojavljuje se isti impuls kao i na početku pokreta. Pol, na kojem se formiraju stop-impuli, definiran je parametrom Stop vrijednost. Ako je 'r' ili 'R' tada se stop-impuls proizvodi na suprotnom od pola start-impulsa. Ako se unese bilo koja druga vrijednost (npr. 'd'), tada je stop-impuls na istom polu. Ako je Runtime prošlo nakon početka pokreta, tada se stop-impuls ne formira. primjer: stop=’r’
|-
|out||char[10]||98||'LLLLHHHHP-'||Svaki znak je odgovoran za tip određenog kanala
*'L'-Lamp;
*'M'-Lamp Inverse;
*'J'-grijanje NE, ventil za grijanje, normalno otvoren;
*'H'-grijanje NC, ventil za grijanje, normalno zatvoren;
*'B'-Roletne (2 pol), žaluzine/zavjese;
*'C'-Rolete Inverse (2 polne), žaluzije/zavjese, invertno otvaranje-zatvaranje;
*'G'-kapija (2-polna), 2-polna kapija;
*'D'-Gate (2-polna) Inverzna, 2-polna kapija, invertna otvaranje-zatvaranje;
*'X'-Gate (1 pol /kratki pritisak), 1 pole kapija;
*'Z'-kapija (1 pol) Inverzna, 1-polna kapija, invertno otvaranje-zatvaranje;
*'V'-ventil (2-polni), 2-polni ventil;
*'W'-ventil (2-polni) Inverzni, 2-polni ventil, obrnuti otvaranje-zatvaranje;
*'R'-ventil (1-polni), 1-polni ventil,;
*'S'-ventil (1 polni) Inverzni, 1-polni ventil, obrnuti otvaranje-zatvaranje;
*'K'-Lock (kratak pritisak);
*'N'-Lock (kratki pritisak) Inverse;
*'P' roletne (2 polne);
*'O'-Blinds Inverse (2 pol), invertno otvaranje-zatvaranje;
*'F'-FanCoil. Grupa1 (Lamp Toggle). Za kontrolu brzine ventilatora;
*'E'-FanCoil. Group2 (Lamp Toggle). Za kontrolu brzine ventilatora;
*'Q'-FanCoil. Grupa 3 (Prebacivanje lampe). Za kontrolu brzine ventilatora;
*'U'-FanCoil. Grupa 4 (Prebacivanje lampe). Za kontrolu brzine ventilatora;
*'I'-FanCoil. Grupa 5 (Prebacivanje lampe). Za kontrolu brzine ventilatora;
*'-'-ništa, ništa nije povezano.
primjer: out='LLB-G-V-W-'
|-
|dm||char[4]||98||‘LLLL’||Svaki znak je odgovoran za tip određenog kanala
*‘g’ – koristiti kao halogena dimer lampa
*‘s’ – Soft Switch, lampa, kada se napajanje uključuje/isključuje glatko (500msec)
*‘k’ – Prekidač, lampa, kada se napajanje uključi/isključi odmah
*‘l’ – LED funkcija, LED lampe koje se mogu prigušiti
*‘v’ – linearna funkcija zatamnjivanja
*‘-‘ – Kanal onemogućen
*‘+’ – Redovni kanal
primjer: dm=’skl-‘
|-
|def||integer 0-250||11-14||100||Podrazumevani nivo osvetljenosti u slučaju resetovanja napajanja (1..250). primjer: def=250
|-
|min||integer 0-100||11-14||0||Minimalni nivo zatamnjenja, primjer: min=10
|-
|max||integer 0-100||11-14||100||Maksimalni nivo zatamnjenja, primer max=95
|-
|start||integer 0-100||11-14||0||Funkcija Start se koristi za lampe kojima nedostaje minimalni napon za uključivanje. Ako je podešena vrijednost niža od početne vrijednosti, lampa se uključuje na početnu vrijednost i njima se svjetlo prigušuje do postavljenog nivoa. primjer: start=60
|-
|force||integer 0-100||11-14||10||Vremensko trajanje početne vrijednosti (mjereno u milisekundama). primjer: force=20
|-
|runtime||integer 0-60000||11-14||1000||Vrijeme rada je brzina promjene svjetline sa 'min' na 'max' (mjereno u milisekundama). primjer: runtime=1000
|-
|offset||integer (+/- 0…39)||39-46||'0'||pomak vrijednosti senzora; Na primjer, pomak je -3,8:
primjer: hw="offset='-3.8'"
|-
|io||char[28]||98||io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'||Svaki znak je odgovoran za tip određenog kanala
*'0' - LED-dimer
*'1' - halogen-dimer
*'2' - linearni dimmer
*'3'..'6' - RGB-3..6 kanali
*'z' - WS2812B -string

HW Postavke

Ime	Vrsta, opseg	SUBID	Podrazumevano	Opis
runtime	integer 0-100	1-10	15	vrijeme rada je vrijeme otvaranja/zatvaranja u sekundama, koristi se za žaluziju, kapiju, ventil (2 polni); Primjer: runtime=15
runtimeopen	integer 0-60000	Blinds subId		Runtimeopen je otvoreno vrijeme u milisekundama, koristi se za roletne; primjer: runtimeopen=15000
runtimeclose	integer 0-60000	Blinds subId		Runtimeclose je vrijeme zatvaranja u milisekundama, koristi se za roletne; primjer: runtimeclose=15000
hold	integer 0-10000	1-10	500	hold je vrijeme premošćavanja u milisekundama, koristi se za kapiju i žaluziju (podrazumevano zadržavanje je isto kao vrijeme izvođenja za žaluziju i vrata), zaključavanje; primjer: hold=3500
def	string 'ON'	1-10	'OFF'	def je status elementa postavljen nakon ponovnog pokretanja, koristi se za lampu, grijanje, ventil (1 pol); primjer: def='ON'
stop	Char ‘R’	1-7	–	(za 2-polne kapije i roletne) Ako se deklariše tada komandom Stop tokom kretanja, pojavljuje se isti impuls kao i na početku pokreta. Pol, na kojem se formiraju stop-impuli, definiran je parametrom Stop vrijednost. Ako je 'r' ili 'R' tada se stop-impuls proizvodi na suprotnom od pola start-impulsa. Ako se unese bilo koja druga vrijednost (npr. 'd'), tada je stop-impuls na istom polu. Ako je Runtime prošlo nakon početka pokreta, tada se stop-impuls ne formira. primjer: stop=’r’
out	char[10]	98	'LLLLHHHHP-'	Svaki znak je odgovoran za tip određenog kanala 'L'-Lamp; 'M'-Lamp Inverse; 'J'-grijanje NE, ventil za grijanje, normalno otvoren; 'H'-grijanje NC, ventil za grijanje, normalno zatvoren; 'B'-Roletne (2 pol), žaluzine/zavjese; 'C'-Rolete Inverse (2 polne), žaluzije/zavjese, invertno otvaranje-zatvaranje; 'G'-kapija (2-polna), 2-polna kapija; 'D'-Gate (2-polna) Inverzna, 2-polna kapija, invertna otvaranje-zatvaranje; 'X'-Gate (1 pol /kratki pritisak), 1 pole kapija; 'Z'-kapija (1 pol) Inverzna, 1-polna kapija, invertno otvaranje-zatvaranje; 'V'-ventil (2-polni), 2-polni ventil; 'W'-ventil (2-polni) Inverzni, 2-polni ventil, obrnuti otvaranje-zatvaranje; 'R'-ventil (1-polni), 1-polni ventil,; 'S'-ventil (1 polni) Inverzni, 1-polni ventil, obrnuti otvaranje-zatvaranje; 'K'-Lock (kratak pritisak); 'N'-Lock (kratki pritisak) Inverse; 'P' roletne (2 polne); 'O'-Blinds Inverse (2 pol), invertno otvaranje-zatvaranje; 'F'-FanCoil. Grupa1 (Lamp Toggle). Za kontrolu brzine ventilatora; 'E'-FanCoil. Group2 (Lamp Toggle). Za kontrolu brzine ventilatora; 'Q'-FanCoil. Grupa 3 (Prebacivanje lampe). Za kontrolu brzine ventilatora; 'U'-FanCoil. Grupa 4 (Prebacivanje lampe). Za kontrolu brzine ventilatora; 'I'-FanCoil. Grupa 5 (Prebacivanje lampe). Za kontrolu brzine ventilatora; '-'-ništa, ništa nije povezano. primjer: out='LLB-G-V-W-'
dm	char[4]	98	‘LLLL’	Svaki znak je odgovoran za tip određenog kanala ‘g’ – koristiti kao halogena dimer lampa ‘s’ – Soft Switch, lampa, kada se napajanje uključuje/isključuje glatko (500msec) ‘k’ – Prekidač, lampa, kada se napajanje uključi/isključi odmah ‘l’ – LED funkcija, LED lampe koje se mogu prigušiti ‘v’ – linearna funkcija zatamnjivanja ‘-‘ – Kanal onemogućen ‘+’ – Redovni kanal primjer: dm=’skl-‘
def	integer 0-250	11-14	100	Podrazumevani nivo osvetljenosti u slučaju resetovanja napajanja (1..250). primjer: def=250
min	integer 0-100	11-14	0	Minimalni nivo zatamnjenja, primjer: min=10
max	integer 0-100	11-14	100	Maksimalni nivo zatamnjenja, primer max=95
start	integer 0-100	11-14	0	Funkcija Start se koristi za lampe kojima nedostaje minimalni napon za uključivanje. Ako je podešena vrijednost niža od početne vrijednosti, lampa se uključuje na početnu vrijednost i njima se svjetlo prigušuje do postavljenog nivoa. primjer: start=60
force	integer 0-100	11-14	10	Vremensko trajanje početne vrijednosti (mjereno u milisekundama). primjer: force=20
runtime	integer 0-60000	11-14	1000	Vrijeme rada je brzina promjene svjetline sa 'min' na 'max' (mjereno u milisekundama). primjer: runtime=1000
offset	integer (+/- 0…39)	39-46	'0'	pomak vrijednosti senzora; Na primjer, pomak je -3,8: primjer: hw="offset='-3.8'"
io	char[28]	98	io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'	Svaki znak je odgovoran za tip određenog kanala '0' - LED-dimer '1' - halogen-dimer '2' - linearni dimmer '3'..'6' - RGB-3..6 kanali 'z' - WS2812B -string

Difference between revisions of "Translations:Metaforsa 3/3.plus/87/bs"

Latest revision as of 08:09, 8 April 2024

HW Postavke

Navigation menu

Search