Tags : Mobile web edit Mobile edit
(No difference)
Latest revision as of 14:31, 8 April 2024
Information about message (contribute ) This message has no documentation.
If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (Metaforsa 3/3.plus )
*'e' - led-button inverse
*'e' - led-button inverse
*'d' - led-button
*'c' - button inverse
*'b' - button
*'s' - switch
*'k' - contact inverse
*'h' - contact
*'l' - leak
*'n' - Neptun
*'v' - motion inverse
*'m' - motion
*'r' - thermo-resistor
*'t' - DALLAS
*'-' - none
Example: io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'
|-
|hw||string||98||-||hw="...", where
*pwm_invert – PWM inverting [1, 0];
*lbn_bright – brightness of led buttons, range (0 - 255);
*f – by default PWM frequency is 1000, range (1 - 5000).
Example:
<syntaxhighlight lang="xml" line>
hw="io='4---zdd----t--' pwm_invert=1 lbn_bright=255 f=1000"
</syntaxhighlight>
|-
|colspan="3"|'''Only for Metaforsa 3.plus'''
|-
|cfg||string||98||9600/8N1||cfg='SPEED/BPS', where
*SPEED – baud rate [1200..115200];
*B – data length [7,8];
*P – presence and type of parity bit [N(No parity),E(Even parity),O(Odd parity)];
*S – stop bit length [1, 1.5 or 2].
Example:
<syntaxhighlight lang="xml" line>
hw="cfg='9600/8N1'"
</syntaxhighlight>
|-
|[Protocol]||string||98||—||Protocol setting is described by protocol parameter. The following
protocols are supported:
*'modbus', Modbus protocol, at the end of redirection the checksum CRC16(Modbus) is added;
*'dmx', DMX protocol;
*'CO2' for connecting Larnitech CO2 sensors;
*'salda' for connecting Salda ventilation.
Example:
<syntaxhighlight lang="xml" line>
hw="cfg='9600/8N1' modbus"
</syntaxhighlight>
|-
|echo||on; off||98||'off'||For settings check out and testing echo parameter can be used. Module
echo-reply can be turned on or off with the help of this parameter.Echo parameter value:
*'off'
*'on'
Example:
<syntaxhighlight lang="xml" line>
hw="cfg='9600/8N1' echo='off'"
</syntaxhighlight>
|} Translation *'e' - LED dugme inverzno 'e' - LED dugme inverzno
'd' - LED dugme
'c' - dugme obrnuto
'b' - dugme
's' - prekidač
'k' - kontakt inverzan
'h' - kontakt
'l' - curenje
'n' - Neptun
'v' - inverzno kretanje
'm' - pokret
'r' - termo-otpornik
't' - DALLAS
'-' - nijedan Primer: io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'
|-
|hw||string||98||-||hw="...", gde
pvm_invert – PVM invertovanje [1, 0];
lbn_bright – osvetljenost LED tastera, opseg (0 - 255);
f – podrazumevano je PVM frekvencija 1000, opseg (1 - 5000). Primer:
1 hw="io='4---zdd----t--' pwm_invert=1 lbn_bright=255 f=1000"
|-
|colspan="3"|Samo za Metaforsa 3.plus
|-
|cfg||string||98||9600/8N1||cfg='SPEED/BPS', gde
SPEED – brzina prenosa [1200..115200];
B – dužina podataka [7,8];
P – prisustvo i tip bita parnosti [N(bez parnosti),E(parni paritet),O(neparni paritet)];
S – dužina stop bita [1, 1,5 ili 2]. Primer:
|-
|[Protocol]||string||98||—||Podešavanje protokola je opisano parametrom protokola. Sledeće
protokoli su podržani:
'modbus', Modbus protokol, na kraju preusmeravanja se dodaje kontrolni zbir CRC16(Modbus);
'dmk', DMKS protokol;
'CO2' za povezivanje Larnitech CO2 senzora;
'salda' za povezivanje Salda ventilacije. Primer:
1 hw="cfg='9600/8N1' modbus"
|-
|echo||on; off||98||'off'||Za proveru podešavanja i testiranje eho parametar se može koristiti. Modul
echo-repli se može uključiti ili isključiti uz pomoć ovog parametra. Vrednost parametra Echo:
Primer:
1 hw="cfg='9600/8N1' echo='off'"
|}