BW-RGB/en

Revision:

A

A/B

/B

/C

BW-RGB.C
Output ports Number of switched channels 3 Peak load 1A (12W at 12V)
Other Supply voltage 11.5...27.5 V DC Dimentions 45x42x14 mm

3-CHANNEL LED CONTROLLER

This module allows controlling RGB strip or three monochrome LED strips.

CAUTION! All work related to the installation, connection, setting up, service and support must be carried out by qualified personnel with sufficient skills and experience in working with electrical equipment. To avoid the risk of fire, electric shock, damage to the system and/or personal injury, the system installation and assembly must be performed in accordance with the instructions listed below:

• all connectivity work must be carried out with the power turned OFF;
• use appropriate tools and personal protection against electric shock;
• do not use damaged cables, wires and connectors;
• avoid folding the cables and wires;
• do not apply excessive force to the wires by kinking or pressing them too hard: the inner conductors of the cables and wires may get stripped or damaged;
• do not use the power socket with poor contacts to connect;
• do not exceed the load limit parameters specified in the manual;
• the supply conductors wire section is subject to the specifications for current density limit, insulation type and wire material. Light section can result in cable overheating and fire.

When the power is on, NEVER:

• connect/disconnect the connectors;
• open modules and sensors.

Example of connection

Example of connection RGB LED with Amp

Module parameters

Parameter name	Value
Input channels qty
Input/output channels qty
0-10 input port quantity
Buttons
LED Buttons
Number of sensor inputs
Number of dry contact inputs
RS485 ports qty
RS232 ports qty
UART ports qty
M-BUS port quantity
Pulse inputs quantity
DALI ports qty
DALI-line voltage supply
Peak current of DALI-line power supply
Peak current in DALI-line
Maximum DALI devices quantity
Dimming channels qty
Output channels qty	3
0-10 output port quantity
Analog output channels qty
Output
Digital line maximum length
Discrete input channels qty
Digital input channels qty
Speakers
Max power output audio channel
Camera
IR lighting
Card reader
Connection type
Protocols
Backlight voltage
Load type
Dimmer load type
Supported sensors
Input voltage	11.5 … 25V
Current type	DC
Adjustment type	PWM
Max load
Min load
Max load per channel	1A (12W at 12V)
Max load per group
Max load per device	3A (36W at 12V)
Control parameters
Angle of vision IR	°
Angle of motion	°
Temperature measuring range	°C
Humidity measuring range
Dimmer type
Dimming type
Voltage that may be applied to the input channels	11.5 … 25V
Max output switching voltage
Max output switching current
Power supply	11.5 … 27.5 V DC from CAN
Max current(24V)	25 mA
Max current(13V)
Max detection distance
Max IR distance
Max BT distance
Max current
Relay
Data transfer speed
Permissible section of power supply cable to connect in socket:
Sensors VCC output
Sensors max VCC current
R1-R2 inputs max current
Push-button/reed switches line recommended length
Temperature sensor line max length
Sensor cable length
Sensors line max length
Bus type	CAN (4-wire)
Compatible with
Output voltage
Output current
Equipment installation type	Free
Mounting
Max cabel lenght
Case material	ABS
Protection	IP40
Temperature range	-10 … +50 °C
Size	45x42x14 mm
Weight	25 g

* -

** -

*** -

1 -

2 -

3 -

Module installation and connection procedure

1. Connect the outputs.
2. Connect the CAN connector.
3. Configure the module using LT setup.
4. Apply power to the load.
5. Check all equipment for proper operation.

Module shut-off and deinstallation procedure

1. Disconnect the power from the load.
2. Disconnect the CAN connector.
3. Disconnect the outputs.

HW settings

Name	Type, range	SUBID	Default	Description
dm	char[3]	98	'RGB'	Each char is responsible for the type of a particular channel, RGB takes 3 channels 'D' – use like dimmer-lamp 'RGB' – Use like RGB lamp Example: dm='DDD'
def	integer 0-250	1-3	100	The default brightness level in case of a power reset (1..250). Example: def=250
min	integer 0-100	1-3	0	Minimum dimming level, example: min=10
max	integer 0-100	1-3	100	Maximum dimming level, example max=95
runtime	integer 0-100	98	5	Runtime is the speed of changing the brightness(measured in seconds). Example: runtime=15
f	integer 1-1000	98	500	It is frequency (measured in Hz); Example: f=500

1<item addr="355:1" auto-period="600" cfgid="175" name="Dimmer" type="dimer-lamp" uniq_id="68"/>
2<item addr="355:2" auto-period="600" cfgid="175" name="Dimmer" type="dimer-lamp" uniq_id="69"/>
3<item addr="355:3" auto-period="600" cfgid="175" name="Dimmer" type="dimer-lamp" uniq_id="70"/>
4<item addr="355:98" cfgid="175" hw="dm='DDD' f=1000 runtime=20" name="Temperature" system="yes" type="temperature-sensor" uniq_id="47"/>