Difference between revisions of "EIB"

From Larnitech wiki page
Jump to navigation Jump to search
(Marked this version for translation)
 
(14 intermediate revisions by 2 users not shown)
Line 1: Line 1:
==Switch-press-release  (Recommended)==
+
<languages/>
 +
<translate>
 +
==Switch-press-release  (Recommended)== <!--T:1-->
 +
For correct operation, it is required that the button, when pressed, should send 1, and when released, 0
 +
This kind of configuration can be used for double, triple clicks and dimming
  
===Button configuration in ETS:===
+
===Button configuration in ETS:=== <!--T:2-->
 
<br>[[File:knx1.png|800px]]</br>
 
<br>[[File:knx1.png|800px]]</br>
 
<br>[[File:knx2.png|800px]]</br>
 
<br>[[File:knx2.png|800px]]</br>
  
===Configuration in EIB plugin:===
+
===Configuration in EIB plugin:=== <!--T:3-->
 
<br>[[File:knx3.png|800px]]</br>
 
<br>[[File:knx3.png|800px]]</br>
  
===LOG:===
+
===LOG:=== <!--T:4-->
  
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/0 data len 1: 01  - '''Button pressed'''
+
  <!--T:5-->
 +
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/0 data len 1: 01  - '''Button pressed'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/0 data len 1: 00  - '''Button released'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/0 data len 1: 00  - '''Button released'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/2 data len 1: 01  - '''Feedback sent'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/2 data len 1: 01  - '''Feedback sent'''
  
===Comment:===
+
==Switch-one-phys-btn== <!--T:6-->
For correct operation, it is required that the button, when pressed, should send 1, and when released, 0
+
Each press of the button sends 1 byte of data (alternately 0 or 1). To start / stop dimming, the button sends 9/8 or 1/0 to the dimming group address.
This kind of configuration can be used for double, triple clicks and dimming
 
 
 
==Switch-one-phys-btn==
 
  
===Button configuration in ETS:===
+
===Button configuration in ETS:=== <!--T:7-->
 
<br>[[File:knx4.png|800px]]</br>
 
<br>[[File:knx4.png|800px]]</br>
 
Or:
 
Or:
Line 27: Line 29:
 
===Configuration in EIB plugin:===
 
===Configuration in EIB plugin:===
  
 +
<!--T:8-->
 
<br>[[File:knx7.png|800px]]</br>
 
<br>[[File:knx7.png|800px]]</br>
  
===LOG:===
+
===LOG:=== <!--T:9-->
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/0 data len 1: 01 - '''Button pressed'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/0 data len 1: 01 - '''Button pressed'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 5/0/1 data len 1: 01 - '''Feedback sent'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 5/0/1 data len 1: 01 - '''Feedback sent'''
  
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/0 data len 1: 00 - '''Button pressed'''
+
  <!--T:10-->
 +
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/0 data len 1: 00 - '''Button pressed'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 5/0/1 data len 1: 00  - '''Feedback sent'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 5/0/1 data len 1: 00  - '''Feedback sent'''
  
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/2 data len 1: 09 - '''Dimming UP started'''
+
  <!--T:11-->
 +
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/2 data len 1: 09 - '''Dimming UP started'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/2 data len 1: 08 - '''Dimming UP finished'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/2 data len 1: 08 - '''Dimming UP finished'''
  
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/2 data len 1: 01 - '''Dimming DOWN started'''
+
  <!--T:12-->
 +
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/2 data len 1: 01 - '''Dimming DOWN started'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/2 data len 1: 00 - '''Dimming DOWN finished'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/2 data len 1: 00 - '''Dimming DOWN finished'''
  
===Comment:===
+
==Switch-two-phys-btn== <!--T:13-->
Each press of the button sends 1 byte of data (alternately 0 or 1). To start / stop dimming, the button sends 9/8 or 1/0 to the dimming group address.
+
This type of configuration is used if you have physically 2 buttons on a panel, one of which always sends the command on (1) and the second off (0). In this case, 2 buttons are created in the Larnitech system, each of which can be used independently.
 +
Most of the panels do not allow independent use of the feedback LEDs, therefore, if the keys are used independently, the indication may not work correctly.
  
==Switch-two-phys-btn==
+
===Button configuration in ETS:=== <!--T:14-->
 
 
===Button configuration in ETS:===
 
 
<br>[[File:knx8.png|800px]]</br>
 
<br>[[File:knx8.png|800px]]</br>
 
<br>[[File:knx9.png|800px]]</br>
 
<br>[[File:knx9.png|800px]]</br>
Line 57: Line 62:
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/0 data len 1: 01  - '''Feedback sent'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/0 data len 1: 01  - '''Feedback sent'''
  
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/2 data len 1: 00 - '''Button 2 pressed'''
+
  <!--T:15-->
 +
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/2 data len 1: 00 - '''Button 2 pressed'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/3 data len 1: 00  - '''Feedback 2 sent'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/3 data len 1: 00  - '''Feedback 2 sent'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/0 data len 1: 00  - '''Feedback sent'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/0 data len 1: 00  - '''Feedback sent'''
  
===Comment:===
+
==Switch-long-press== <!--T:16-->
This type of configuration is used if you have physically 2 buttons on a panel, one of which always sends the command on (1) and the second off (0). In this case, 2 buttons are created in the Larnitech system, each of which can be used independently.
+
Works the same as Switch-two-phys-btn, the difference is that dimming is added.
Most of the panels do not allow independent use of the feedback LEDs, therefore, if the keys are used independently, the indication may not work correctly.
 
 
 
  
==Switch-long-press==
+
===Button configuration in ETS:=== <!--T:17-->
===Button configuration in ETS:===
 
 
<br>[[File:knx8.png|800px]]</br>
 
<br>[[File:knx8.png|800px]]</br>
 
<br>[[File:knx9.png|800px]]</br>
 
<br>[[File:knx9.png|800px]]</br>
 
<br>[[File:knx13.png|800px]]</br>
 
<br>[[File:knx13.png|800px]]</br>
  
===Configuration in EIB plugin:===
+
===Configuration in EIB plugin:=== <!--T:18-->
 
<br>[[File:knx14.png|800px]]</br>
 
<br>[[File:knx14.png|800px]]</br>
===LOG:===
+
 
 +
===LOG:=== <!--T:19-->
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/2 data len 1: 01  - '''Button 1 pressed'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/2 data len 1: 01  - '''Button 1 pressed'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/3 data len 1: 01 - '''Feedback 2 sent'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/3 data len 1: 01 - '''Feedback 2 sent'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/0 data len 1: 01 - '''Feedback sent'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/0 data len 1: 01 - '''Feedback sent'''
  
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/2 data len 1: 00  - '''Button 2 pressed'''
+
  <!--T:20-->
 +
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/2 data len 1: 00  - '''Button 2 pressed'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/3 data len 1: 00 - '''Feedback 2 sent'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/3 data len 1: 00 - '''Feedback 2 sent'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/0 data len 1: 00 - '''Feedback sent'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/0 data len 1: 00 - '''Feedback sent'''
  
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/1 data len 1: 01 - '''Button 1 dimming started'''
+
  <!--T:21-->
 +
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/1 data len 1: 01 - '''Button 1 dimming started'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/1 data len 1: 00 - '''Button 1 dimming finished'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/1 data len 1: 00 - '''Button 1 dimming finished'''
  
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/1 data len 1: 09 - '''Button 2 dimming started'''
+
  <!--T:22-->
 +
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/1 data len 1: 09 - '''Button 2 dimming started'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/1 data len 1: 08 - '''Button 2 dimming finished'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/1 data len 1: 08 - '''Button 2 dimming finished'''
  
===Comment:===
+
==Temperature Sensor== <!--T:23-->
Works the same as Switch-two-phys-btn, the difference is that dimming is added.
+
Creates a temperature sensor in the Larnitech system.
 
 
 
 
  
==Temperature Sensor==
+
===Sensor configuration in ETS:=== <!--T:24-->
 
 
===Sensor configuration in ETS:===
 
 
<br>[[File:knx15.png|800px]]</br>
 
<br>[[File:knx15.png|800px]]</br>
 
<br>[[File:knx16.png|800px]]</br>
 
<br>[[File:knx16.png|800px]]</br>
  
===Configuration in EIB plugin:===
+
===Configuration in EIB plugin:=== <!--T:25-->
 
<br>[[File:knx17.png|800px]]</br>
 
<br>[[File:knx17.png|800px]]</br>
  
===LOG:===
+
===LOG:=== <!--T:26-->
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/1/5 data len 3: 00 0c c4  - '''Received temperature from the sensor'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/1/5 data len 3: 00 0c c4  - '''Received temperature from the sensor'''
  
===Comment:===
+
==Thermostat== <!--T:27-->
Creates a temperature sensor in the Larnitech system.
+
The plugin ensures temperature setpoint synchronization between a thermostat and valve-heating element in the Larnitech system
 
 
==Thermostat==
 
  
===Thermostat configuration in ETS:===
+
===Thermostat configuration in ETS:=== <!--T:28-->
 
<br>[[File:knx18.png|800px]]</br>
 
<br>[[File:knx18.png|800px]]</br>
 
<br>[[File:knx19.png|800px]]</br>
 
<br>[[File:knx19.png|800px]]</br>
 
<br>[[File:knx20.png|800px]]</br>
 
<br>[[File:knx20.png|800px]]</br>
  
===Configuration in EIB plugin:===
+
===Configuration in EIB plugin:=== <!--T:29-->
 
<br>[[File:knx21.png|800px]]</br>
 
<br>[[File:knx21.png|800px]]</br>
  
===LOG:===
+
===LOG:=== <!--T:30-->
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 4/0/2 data len 3: 00 0c 4c - '''Setpoint sent to the thermostat'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 4/0/2 data len 3: 00 0c 4c - '''Setpoint sent to the thermostat'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0c 4c - '''Setpoint received from the thermostat'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0c 4c - '''Setpoint received from the thermostat'''
  
===Comment:===
+
==Climate Control== <!--T:31-->
The plugin ensures temperature setpoint synchronization between a thermostat and valve-heating element in the Larnitech system
+
Heat/Cool Setpoint - Must be selected if the thermostat panel has only 1 address for two setpoints. In this case, depending on the selected mode in the climate control, the following values will be taken:
 
+
*If climate control is in heating mode, Heat/Cool setpoint will be accepted as the heating setpoint. Likewise within the Cooling mode, Heat/Cool setpoint will be accepted as the cooling setpoint.
==Climate Control==
+
*If the climate control is in the Heating/Cooling mode, it will use add/subtract delta  and set 2 setpoints (Heat and cool). For example setpoint 25 will be transformed to 23-27.
  
===Thermostat configuration in ETS:===
+
===Thermostat configuration in ETS:=== <!--T:32-->
 
<br>[[File:knx22.png|800px]]</br>
 
<br>[[File:knx22.png|800px]]</br>
 
<br>[[File:knx23.png|800px]]</br>
 
<br>[[File:knx23.png|800px]]</br>
Line 136: Line 137:
 
<br>[[File:knx27.png|800px]]</br>
 
<br>[[File:knx27.png|800px]]</br>
  
===Configuration in EIB plugin:===
+
===Configuration in EIB plugin:=== <!--T:33-->
 
<br>[[File:knx28.png|800px]]</br>
 
<br>[[File:knx28.png|800px]]</br>
 
<br>[[File:knx29.png|800px]]</br>
 
<br>[[File:knx29.png|800px]]</br>
Line 142: Line 143:
  
  
===LOG:===
+
===LOG:=== <!--T:34-->
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/3/1 data len 1: 00 - '''Turn OFF'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/3/1 data len 1: 00 - '''Turn OFF'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0d 46 - '''Setpoint received'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0d 46 - '''Setpoint received'''
  
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/3/1 data len 1: 01 - '''Turn ON'''
+
  <!--T:35-->
 +
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/3/1 data len 1: 01 - '''Turn ON'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0d 46 - '''Setpoint received'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0d 46 - '''Setpoint received'''
  
  From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 4/0/2 data len 3: 00 0c e2 - '''Setpoint sent to the thermostat'''
+
  <!--T:36-->
 +
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 4/0/2 data len 3: 00 0c e2 - '''Setpoint sent to the thermostat'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0c e2 - '''Setpoint received'''
 
  From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0c e2 - '''Setpoint received'''
  
===Comment:===
+
==Air Conditioner== <!--T:37-->
 +
In case the device does can't send mode with the DPT 20.105 data type, but simply sends [1,2,3,4,0…], you can set your own correspondence of values to the mode
  
Heat/Cool Setpoint - Must be selected if the thermostat panel has only 1 address for two setpoints. In this case, depending on the selected mode in the climate control, the following values will be taken:
+
===Configuration in ETS:=== <!--T:38-->
*If climate control is in heating mode, Heat/Cool setpoint will be accepted as the heating setpoint. Likewise within the Cooling mode, Heat/Cool setpoint will be accepted as the cooling setpoint.
 
*If the climate control is in the Heating/Cooling mode, it will use add/subtract delta  and set 2 setpoints (Heat and cool). For example setpoint 25 will be transformed to 23-27.
 
 
 
 
 
==Air Conditioner==
 
 
 
===Configuration in ETS:===
 
 
<br>[[File:knx31.png|800px]]</br>
 
<br>[[File:knx31.png|800px]]</br>
 
<br>[[File:knx32.png|800px]]</br>
 
<br>[[File:knx32.png|800px]]</br>
Line 172: Line 169:
  
  
===Configuration in EIB plugin:===
+
===Configuration in EIB plugin:=== <!--T:39-->
 
<br>[[File:knx39.png|800px]]</br>
 
<br>[[File:knx39.png|800px]]</br>
 
<br>[[File:knx40.png|800px]]</br>
 
<br>[[File:knx40.png|800px]]</br>
  
===LOG:===
+
===LOG:=== <!--T:40-->
  
 +
<!--T:41-->
 
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/3/1 data len 1: 00 - '''Turn OFF'''
 
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/3/1 data len 1: 00 - '''Turn OFF'''
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0d 46 - '''Setpoint received'''
+
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0d 46 - '''Setpoint received'''
  
 +
<!--T:42-->
 
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/3/1 data len 1: 01 - '''Turn ON'''
 
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/3/1 data len 1: 01 - '''Turn ON'''
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0d 46 - '''Setpoint received'''
+
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0d 46 - '''Setpoint received'''
  
 +
<!--T:43-->
 
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/2/0 data len 2: 00 04 - '''Mode changed to Heating'''
 
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/2/0 data len 2: 00 04 - '''Mode changed to Heating'''
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 4/0/2 data len 3: 00 0c e2 - '''Setpoint sent'''
+
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 4/0/2 data len 3: 00 0c e2 - '''Setpoint sent'''
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0c e2 - '''Setpoint received'''
+
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0c e2 - '''Setpoint received'''
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/4/0 data len 2: 00 03 - '''Sending FAN speed'''
+
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/4/0 data len 2: 00 03 - '''Sending FAN speed'''
 
+
</translate>
===Comment:===
 
 
 
In case the device does can't send mode with the DPT 20.105 data type, but simply sends [1,2,3,4,0…], you can set your own correspondence of values to the mode
 

Latest revision as of 15:10, 15 January 2022

Other languages:
English • ‎русский

Switch-press-release (Recommended)

For correct operation, it is required that the button, when pressed, should send 1, and when released, 0 This kind of configuration can be used for double, triple clicks and dimming

Button configuration in ETS:


Knx1.png

Knx2.png

Configuration in EIB plugin:


Knx3.png

LOG:

From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/0 data len 1: 01  - Button pressed
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/0 data len 1: 00  - Button released
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/2 data len 1: 01  - Feedback sent

Switch-one-phys-btn

Each press of the button sends 1 byte of data (alternately 0 or 1). To start / stop dimming, the button sends 9/8 or 1/0 to the dimming group address.

Button configuration in ETS:


Knx4.png
Or:
Knx5.png

Knx6.png

Configuration in EIB plugin:


Knx7.png

LOG:

From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/0 data len 1: 01 - Button pressed
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 5/0/1 data len 1: 01 - Feedback sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/0 data len 1: 00 - Button pressed
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 5/0/1 data len 1: 00  - Feedback sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/2 data len 1: 09 - Dimming UP started
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/2 data len 1: 08 - Dimming UP finished
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/2 data len 1: 01 - Dimming DOWN started
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/2 data len 1: 00 - Dimming DOWN finished

Switch-two-phys-btn

This type of configuration is used if you have physically 2 buttons on a panel, one of which always sends the command on (1) and the second off (0). In this case, 2 buttons are created in the Larnitech system, each of which can be used independently. Most of the panels do not allow independent use of the feedback LEDs, therefore, if the keys are used independently, the indication may not work correctly.

Button configuration in ETS:


Knx8.png

Knx9.png

Configuration in EIB plugin:


Knx10.png

LOG:

From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/2 data len 1: 01 - Button 1 pressed
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/3 data len 1: 01  - Feedback 2 sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/0 data len 1: 01  - Feedback sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/2 data len 1: 00 - Button 2 pressed
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/3 data len 1: 00  - Feedback 2 sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/0 data len 1: 00  - Feedback sent

Switch-long-press

Works the same as Switch-two-phys-btn, the difference is that dimming is added.

Button configuration in ETS:


Knx8.png

Knx9.png

Knx13.png

Configuration in EIB plugin:


Knx14.png

LOG:

From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/2 data len 1: 01  - Button 1 pressed
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/3 data len 1: 01 - Feedback 2 sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/0 data len 1: 01 - Feedback sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/2 data len 1: 00  - Button 2 pressed
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/3 data len 1: 00 - Feedback 2 sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/0 data len 1: 00 - Feedback sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/1 data len 1: 01 - Button 1 dimming started
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/1 data len 1: 00 - Button 1 dimming finished
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/1 data len 1: 09 - Button 2 dimming started
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/1 data len 1: 08 - Button 2 dimming finished

Temperature Sensor

Creates a temperature sensor in the Larnitech system.

Sensor configuration in ETS:


Knx15.png

Knx16.png

Configuration in EIB plugin:


Knx17.png

LOG:

From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/1/5 data len 3: 00 0c c4  - Received temperature from the sensor

Thermostat

The plugin ensures temperature setpoint synchronization between a thermostat and valve-heating element in the Larnitech system

Thermostat configuration in ETS:


Knx18.png

Knx19.png

Knx20.png

Configuration in EIB plugin:


Knx21.png

LOG:

From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 4/0/2 data len 3: 00 0c 4c - Setpoint sent to the thermostat
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0c 4c - Setpoint received from the thermostat

Climate Control

Heat/Cool Setpoint - Must be selected if the thermostat panel has only 1 address for two setpoints. In this case, depending on the selected mode in the climate control, the following values will be taken:

  • If climate control is in heating mode, Heat/Cool setpoint will be accepted as the heating setpoint. Likewise within the Cooling mode, Heat/Cool setpoint will be accepted as the cooling setpoint.
  • If the climate control is in the Heating/Cooling mode, it will use add/subtract delta and set 2 setpoints (Heat and cool). For example setpoint 25 will be transformed to 23-27.

Thermostat configuration in ETS:


Knx22.png

Knx23.png

Knx19.png

Knx20.png

Knx26.png

Knx27.png

Configuration in EIB plugin:


Knx28.png

Knx29.png

Knx30.png


LOG:

From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/3/1 data len 1: 00 - Turn OFF
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0d 46 - Setpoint received
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/3/1 data len 1: 01 - Turn ON
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0d 46 - Setpoint received
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 4/0/2 data len 3: 00 0c e2 - Setpoint sent to the thermostat
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0c e2 - Setpoint received

Air Conditioner

In case the device does can't send mode with the DPT 20.105 data type, but simply sends [1,2,3,4,0…], you can set your own correspondence of values to the mode

Configuration in ETS:


Knx31.png

Knx32.png

Knx19.png

Knx20.png

Knx26.png

Knx27.png

Knx37.png

Knx38.png


Configuration in EIB plugin:


Knx39.png

Knx40.png

LOG:

From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/3/1 data len 1: 00 - Turn OFF
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0d 46 - Setpoint received
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/3/1 data len 1: 01 - Turn ON
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0d 46 - Setpoint received
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/2/0 data len 2: 00 04 - Mode changed to Heating
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 4/0/2 data len 3: 00 0c e2 - Setpoint sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0c e2 - Setpoint received
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/4/0 data len 2: 00 03 - Sending FAN speed