Metaforsa 3/3.plus/nl

MF3/MF3.plus
Output ports Number of switched channels 10 Number of dimming channels 4 Peak load 16 A Max load per dimming channel 0.5 A (110 W at 220 V) Dimmer type MOSFET
Input ports Number of discrete inputs 28
General Max CAN devices 4 (can be extended with the license) 99 (for Metaforsa 3.plus) Max CAN bus length 800 m (twisted pair CAT5e) Max current per CAN bus 500 mA
Other Supply voltage 11.5...27.5 V DC Dimentions 9U, 156x90x58 mm

Introductie

METAFORSA SMART HOUSE Installatiehandleiding beschrijft de procedure voor de installatie, montage, bediening en instelling. Tijdens het werken met het systeem dient u zich strikt te houden aan alle eisen die in deze handleiding worden gesteld. Het niet naleven ervan kan leiden tot schade aan het apparaat, defecten ervan, elektrische schokken, brand en andere gevolgen. De fabrikant behoudt zich het recht voor om zonder voorafgaande kennisgeving wijzigingen in deze handleiding aan te brengen. Deze handleiding is een integraal onderdeel van het systeem en blijft bij de eindgebruiker.

Features

• 10 universele uitgangen ondersteunen:
  • Lichten
  • NC/NO verwarmingskleppen
• Jaloezieën
  • 1 of 2-polige poorten
  • 1 of 2-polige kleppen
  • NC/NO sloten
  • Ventilatorconvectoren
• 4 dimuitgangen
• 28 ingangen die ondersteunen:
  • Knoppen
  • LED knoppen
  • Schakelaars
  • Schakelaars
  • Leksensoren
  • Bewegingsmelders
  • Temperatuursensoren
  • LED-strips
  • 3-4-5-kanaals RGB-strips
  • WS2812B-strips
  • RS485-apparaten (alleen voor Metaforsa 3.plus)
• Uitbreidingspoort
• Relais met AgSnO2-contacten geschikt voor 80 A 20 ms inschakelstroom
• Cloud-verbinding en besturing van alle huissystemen
• Spraakbesturing (Siri, Alexa, Google Home)

Vertaald met DeepL.com (gratis versie)

Veiligheidseisen

VOORZICHTIGHEID! Alle werkzaamheden met betrekking tot de installatie, aansluiting, opstelling, service en ondersteuning moeten worden uitgevoerd door gekwalificeerd personeel met voldoende vaardigheden en ervaring in het werken met elektrische apparatuur.

Om het risico op brand, elektrische schokken, schade aan het systeem en/of persoonlijk letsel te voorkomen, moet de installatie en montage van het systeem worden uitgevoerd in overeenstemming met de onderstaande instructies:

• alle aansluitwerkzaamheden moeten zonder stroom worden uitgevoerd;
• gebruik geschikt gereedschap en persoonlijke bescherming tegen elektrische schokken;
• gebruik geen beschadigde kabels, draden en connectoren;
• voorkom het vouwen van kabels en draden;
• knel of knik de kabels en draden niet door te veel kracht uit te oefenen. Anders kunnen de binnenste geleiders van de kabels en draden worden gestript of gebroken;
• Gebruik geen stopcontact met slechte contacten om aan te sluiten;
• overschrijd de limiet van de belastingsparameters zoals aangegeven in deze handleiding niet;
• het draadgedeelte van de voedingsgeleiders is onderhevig aan de specificaties voor stroomdichtheidslimiet, isolatietype en draadmateriaal. Lichte sectie kan leiden tot oververhitting van de kabel en brand.

Bij werkzaamheden met het systeem na spanningstoevoer NOOIT:

• aansluiten/loskoppelen van connectoren;
• open modules en sensoren.

Systeemconfiguratie en doel

Doel van het systeem

METAFORSA SMART HOUSE is een kant-en-klare oplossing voor de automatisering van residentiële en commerciële gebouwen en hotelcomplexen die de meest gewenste kenmerken van Smart House omvat.

Het apparaat heeft 10 bedieningskanalen, 4 dimkanalen en 28 invoerkanalen qty.

Universele uitgangen kunnen worden gebruikt om:	Op universele ingangen kun je aansluiten:
Verlichting Knoppen/LED-knoppen/schakeleenheden
Contactdoosconnectoren Magnetische reed-schakelaars
Vloerverwarming Lekdetectors
Bewegingsmelders
Poortbedieningen Temperatuursensoren
LED-strips/3-4-5-kanaals RGB-strips/WS2812B strips
Verwarmingskleppen RS485-apparaten*

* - Alleen voor Metaforsa 3.plus

Uitbreidingspoort

Met de uitbreidingspoort kunt u het systeem upgraden door hulpapparatuur aan te sluiten, zoals de besturingsmodule voor LED-verlichting, dimmen, meetapparatuur en andere elementen. Het pakket, dat volledig installatieklaar is, omvat de basishardware en -software.

Inhoud pakket

Het pakket wordt standaard geleverd met:

1 pc

1 pc

3 stuks

2 stuks

Temperatuurgevoelig element FW-TS 4 stuks

4 st.

1 st.

1 pc

Technische basisspecificaties van het systeem

De basisspecificaties en kenmerken van de module METAFORSA 3/3.plus zijn weergegeven in tabel 1

Tabel 1

Specificatie	Betekenis
Uitgangspoorten
Aantal geschakelde kanalen	10
Aantal geschakelde groepen	10
Aantal dimkanalen	4
Commutatiespanning	0-250 V AC/DC
Piekbelasting (één kanaal)	16A
Piekbelasting (apparaat)	160A
Max. belasting per dimkanaal	0,5A (110W bij 220V)
Dimmertype	MOSFET
Type dimmerbelasting	R,C
Dimtype	achterrand
Type aansluiting voedingskabel	aansluiting
Toegestane doorsnede van de voedingskabel voor aansluiting op stopcontact: enkeladerige kabel meeraderige kabel meeraderige kabel met punt	0,5 … 4 mm2 0,5 … 4 mm2 0,5 … 2,5 mm2
Invoerpoorten
Aantal discrete ingangen	28
Maximale stroomsterkte op de gelijkstroomspanningsconnectoren	5 mA*
Anders
Bedrijfstemperatuur	0 … +45°С
Opslag-/transporttemperatuur	-10 … +50°С
Toegestane vochtigheid	0 … 95% (niet-condenserend)
Voeding	11,5 … 27,5 V DC 24 V, 0,75 A Aanbevolen
Maximale vraag	0,5А
Beschikbare interfaces	Ethernet, KAN
Bustype	CAN (4-draads)
KAN (4-draads)	800 m** (twisted pair CAT5e)
CAN-draadtype	FTP-Cat 5E
CAN-verbindingstype	Connector
Maximale lengte digitale lijn	30 m
Digitaal lijnbedradingstype	UTP/FTP Cat 5E
LAN maximale lengte	100 m
LAN-draadtype	UTP/FTP Cat 5E
LAN-verbindingstype	Connector RJ-45
RS485-poorten aantal	1***
Gegevensoverdrachtsnelheid	1200-115200 b/s***
Dimensionale specificaties	9U, 156x90x58 mm
Schelpmateriaal	buikspieren
Behuizing	IP40
Installatietype apparatuur	DIN-rail (EN 60715)
Gewicht	400 gr

* – Uitgangskanalen mogen alleen worden aangesloten met behulp van een versterker die een 5V PWM-signaal van de IO-uitgang als ingang gebruikt

** - voor lange lijnen is het installeren van extra voedingseenheden vereist; de maximale lengte van de lijn kan worden beperkt door verschillende storingsfactoren

*** - Alleen voor Metaforsa 3.plus

Algemene structuur van het systeem

Het algemene overzicht van de module wordt getoond in fig. 1

1	- connector voor belastingstoepassing
| - connector voor toepassing met dimlampen
3	- Voedingsconnector
4	- Ethernet netwerk connector
- connector voor uitbreidingsmodule.

Overzicht van de externe connectoren van het METAFORSA-apparaat: Bovenaan de behuizing (fig. 1) bevindt zich:

• connector (1) — Apparatenaansluiting;
• connector (2) — Aansluiting lampen dimmen;

Onderaan de behuizing (fig. 1) bevindt zich:

• connector (3) - voedingsaansluiting voor module;
• connector (4) - aansluiting ethernetnetwerk;
• connectoren (5-6) - aansluiting universele in-/uitgangskanalen - knoppen, reed-schakelaars, LED-knoppen, leksensoren, bewegingssensoren, temperatuursensoren, LED-strips, 3-4-5-kanaals RGB-strips, WS2812B-strips, RS485-apparaten (alleen voor Metaforsa 3.plus);
• connector (7) - aansluiting voor uitbreidingsmodule.

De fysieke configuratie en contactpunttoewijzing van elke connector worden weergegeven in tabel 2.

Tabel 2

Connector	Contact	Assignment
	1-10	Belastingstoepassing (lampen, thermische aandrijvingen, enz.)
	D1-4, L, N	Belastingstoepassing (lampen dimmen)
Apparaatstatusindicatoren		De modulestatusindicatoren worden beschreven in tabel 3'.
	+24V GND	+24V - voeding van de module door een externe 24V-voeding GND - gemeenschappelijk
	RJ45	Aansluiting voor LAN-aansluiting
	In1-14, In15-28 GND	Aansluiting regelapparaten (knoppen, LED-knoppen, magnetische reed-schakelaars, bewegingsdetectoren, leksensoren, temperatuursensoren enz:) In1 ... In28 - logische ingangen GND - gemeenschappelijk
	VCC GND L H	Aansluiting externe modules voor CAN-bus С - 24V uitgang voor voeding externe apparaten GND - common L - CAN-L databus H - CAN-H databus

Table3

Indicator	Status	Description
Power		Power
		Power not available
Activity		Data communication
		Data communication not available
Error		No errors
		Communication error
		Module overheat
		Dimmer outputs module overload
		Absence of power on dimmers, if in configuration

Systeeminstallatie en montage

Voordat u het systeem aansluit, moet u:

• plaats de sensor en actuatoren (indien niet vooraf geïnstalleerd), stel de sensoren en actuatoren in;
• plaats de module en de voeding.

Note: The module must be installed near the power supply voltage source.

CAUTION! AC power voltage must be provided to the system input through the circuit breaker assembly. It should be installed close to the power supply.

1. The power of circuit breaker assembly must comply with the load capacity;
2. Nothing else than the phase conductors can be connected to the module, the neutral wire is connected separately.

Typical diagram of METAFORSA 3/3.plus module connection is shown in fig. 3.

Connection of the actuators

Connection of the lights/electric contactor/heating thermal actuator

Fig. 4

Such actuators as light, electric contactor, heating thermal actuator should be switched on any of the outputs 1 – 10, the neutral wire and the ground wire should be connected directly to the switchboard. The example of connection is shown in Fig.4.

Connection of high load device

Recomended contactors: ABB ESB series Schneider Acti 9 iCT series Hager ESC series.

Connection of single-pole water/gas supply valve

Caution: Before applying power to the load, make sure that the output configuration of METAFORSA module is correct. The incorrect configuration or incorrect connection can cause the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 5	The single pole water/gas supply valve is connected to any of the outputs of 1 – 10, the (neutral wire and the ground wire are connected directly to the switchboard. The example of connection is shown in Fig.5.

Connection of double-pole water/gas supply valve

Caution: Before applying power to the valve, it is necessary to ensure the output configuration of METAFORSA module is correct. The incorrect configuration can cause the voltage application simultaneously to both channels of the valve, which may result in the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 6	Two adjacent contact points (for example, 3, 4) are used to connect the double-pole water/gas supply valve; in these conditions the neutral wire and the ground wire are connected directly to the switchboard. The example of connection is shown in Fig.6.

Connection of single-pole gate actuator

Caution: Before applying power to the module, you should properly configure access to the application. The contacts incorrectly configured can result in the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 7	Any contact point (for example, 3) is used to connect the single-pole gate drive controllers. The example of connection is shown in Fig.7.

Connection of double-pole gate actuator

Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 8	Two adjacent contact points (for example, 3, 4) should be used to connect the double-pole gate drive controller. The example of connection is shown in Fig.8.

Connection of curtain/jalousie/shutter actuator with 220V force control

Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 9	Two adjacent contact points (for example, 3, 4) should be used to connect the curtain/jalousie/rolladens actuator, in these conditions the neutral wire and the ground wire are connected directly to the switchboard. The example of connection is shown in Fig.9.

Connection of curtain/jalousie/shutter actuator with low-voltage control

Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 10	Two adjacent contact points (for example, 3, 4) should be used to connect the curtain/jalousie/rolladens actuator with low-voltage control. The example of connection is shown in Fig.10.

Connection of sensing elements/switches/buttons

Connection of motion sensors/leakage sensors

The motion sensors/leakage sensors should be connected to any free input in1-in28; in these conditions their power is connected to the contact points of +5V and GND of the relevant group. The example of connection is shown in Fig.11.

Fig. 11 connection of motion sensors/leakage sensors

Connection of buttons/switches/magnetic reed switches

Buttons and reed switches are connected to any free input in1-in28, while their second contact point is connected to GND point of the relevant METAFORSA module group. The example of connection is shown in Fig. 12-13.

Fig. 12 connection of buttons/switching units

Fig. 13 connection of the magnetic reed switches (window/door position sensors)

Connection of temperature sensors

Temperature sensors are connected to any free input in1-in28, while their second contact point is connected to GND point of the relevant METAFORSA module group. The example of connection is shown in Fig. 14.

Fig. 14 connection of temperature sensors

RGB connection scheme

CAUTION! Output channels should only be connected using amplifier which uses 5V PWM signal from IO output as input

Fig. 15 RGB connection

WS2812B connection scheme

Fig. 16 WS2812B connection

RS485 connection scheme

CAUTION! RS485 connection is only available for Metaforsa 3.plus and only occurs on 21 channel

Fig. 17 RS485 connection

Connection of auxiliary equipment.

Expansion modules include Larnitech equipment connected through the CAN-bus. Such equipment includes: dimmers, RGB-backlit control modules, multimode sensors, etc. The equipment connected to the expansion port is defined automatically and does not require any preset tuning. Connector contact pin assignment is defined in Table 4. The example of connection is shown in Fig. 18.

Caution! The 120 ohm terminating resistors should be installed at the end connectors between L and H contact points of CAN-bus. Ensure the connection is correct. The incorrect connection may cause sensor and/or module malfunction.

Module installation and connection procedure

ATTENTION! You must precisely follow the recommendations listed in the Security Requirements section hereof.

1. Install the module in the switchboard on the DIN-rail and fix it with the special latch on the module base.
2. Fasten the supply unit on the left side of the module.
3. Connect the connector (4) having the noise filter pre-installed which is supplied complete with the module.
4. Connect the connectors (5), (6).
5. Connect the connectors (1), (2).
6. Connect the connector (3).
7. Apply power to the supply unit of METAFORSA module.
8. Wait until the module is loaded, then configure it in accordance with the System Setup Instructions.
9. Apply power to the connectors (1), (2).
10. Check all equipment for proper operation.

METAFORSA module shut-off and deinstallation procedure

1. De-energize the module by disconnecting the circuit breaker assembly of the load power supply and METAFORSA module supply unit. Verify the voltage is absent on the terminals (1), (2) of the connector wires and on the input terminals of the supply unit.
2. Disconnect the load power supply connectors (1), (2).
3. Disconnect the connector (3).
4. Disconnect the connectors (4)-(6).
5. Remove the module from the DIN-rail, releasing the latch at the bottom of the module base.

Hardware setup

To configure and control METAFORSA SMART HOUSE, you must install Larnitech software on your smartphone or tablet, which is available in App Store and Play Market. After installation, follow the System Setup Instructions.

Fault diagnostics and handling

The following are some possible faults and ways of fault handling. If you have any difficulty, or face the fault undeclared here, please contact the Technical Support: [1] or [support@larnitech.com]. There are also some tips in the FAQ section at our website [2].

The actuators do not operate:

• ensure the outputs are properly configured in the application (see System Setup Instructions);
• check the connection is correct in accordance with table 2 and paragraph 3.6;
• ensure the power is supplied to the input power contact , i.e. all circuit breaker assembly are ON.
• verify the operability of the connected equipment.

The module is off, indication absent:

• check the connection to 24V supply unit as shown in table 2 (contacts pin assignment);
• check the connection of the supply unit to 220V power mains, the indicator should be ON.

Network connection fault:

• ensure the Ethernet cable is properly wired and connected to the connector;
• ensure the LED status indicators are ON on the Ethernet connector;
• check the LAN configuration is correct, Ethernet cable loops are absent;
• METAFORSA module and the device you are connecting from are in the same network.

hold integer 0-10000 1-10 by default hold is the same as runtime hold is the bridging time in miliseconds, is used for gate and jalousie, lock; Example: hold=3500

The sensors do not operate:

• ensure the inputs are properly configured in the application (System Setup Instructions);
• check the connection is correct in accordance with table 2 and paragraph 3.7;
• ensure the METAFORSA module is ON: circuit breaker assembly is closed, indication on the supply unit is ON, the module indication corresponds to the operating status – table 3;
• check the power supply availability on the sensors;
• check the integrity of lines laid to the sensors.

The auxiliary equipment does not operate:

• check the connection is correct in accordance with table 2 and paragraph 3.8-9;
• ensure the METAFORSA module is ON: circuit breaker assembly is closed, indication on the supply unit is ON, the module indication corresponds to the operating status – table 3;
• check the integrity of the CAN lines, voltage supply on the modules.

HW Settings

Name	Type, range	SUBID	Default	Description
runtime	integer 0-100	1-10	15	runtime is the open/close time in seconds, is used for jalousie, gate, valve(2 pole); Example: runtime=15
runtimeopen	integer 0-60000	Blinds subId		Runtimeopen is the open time in milliseconds, is used for blinds; Example: runtimeopen=15000
runtimeclose	integer 0-60000	Blinds subId		Runtimeclose is the close time in milliseconds, is used for blinds; Example: runtimeclose=15000
hold	integer 0-10000	1-10	500	hold is the bridging time in milliseconds, is used for gate and jalousie (by default hold is the same as runtime for jalousie and gate), lock; Example: hold=3500
def	string 'ON'	1-10	'OFF'	def is the element status is set after restart, is used for lamp, heating, valve(1 pole); Example: def='ON'
stop	Char ‘R’	1-7	–	(for 2-pole gate and blinds) If it is declared then by Stop command during the motion, the same impulse appears as it was at the beginning of the motion. Pole, an which the stop-impules is formed, is defined by the parameter Stop value. If it is ‘r’ or ‘R’ then stop-impulse is produced on the opposite to the start-impulse pole. If any other value is delcared (e.g., ‘d’ ) then the stop-impulse is on the same pole. If a Runtime passed after the beginning of the motion then the stop-impulse is not formed. Example: stop=’r’
out	char[10]	98	'LLLLHHHHP-'	Each char is responsible for the type of a particular channel 'L'-Lamp; 'M'-Lamp Inverse; 'J'-Heating NO, valve-heating, normally open; 'H'-Heating NC, valve-heating, normally closed; 'B'-Blinds (2 pole), jalousie/curtains; 'C'-Blinds Inverse (2 pole), jalousie/curtains, invert open-close; 'G'-Gate (2 pole), 2 pole gate; 'D'-Gate (2 pole) Inverse, 2 pole gate, invert open-close; 'X'-Gate (1 pole /short press), 1 pole gate; 'Z'-Gate (1 pole) Inverse, 1 pole gate, invert open-close; 'V'-Valve (2 pole), 2 pole valve; 'W'-Valve (2 pole) Inverse, 2 pole valve, invert open-close; 'R'-Valve (1 pole), 1 pole valve,; 'S'-Valve (1 pole) Inverse, 1 pole valve, invert open-close; 'K'-Lock (short press); 'N'-Lock (short press) Inverse; 'P'-Blinds (2 pole); 'O'-Blinds Inverse (2 pole), invert open-close; 'F'-FanCoil. Group1 (Lamp Toggle). For fancoil speed control; 'E'-FanCoil. Group2 (Lamp Toggle). For fancoil speed control; 'Q'-FanCoil. Group3 (Lamp Toggle). For fancoil speed control; 'U'-FanCoil. Group4 (Lamp Toggle). For fancoil speed control; 'I'-FanCoil. Group5 (Lamp Toggle). For fancoil speed control; '-'-none, nothing is connected. Example: out='LLB-G-V-W-'
dm	char[4]	98	‘LLLL’	Each char is responsible for the type of a particular channel ‘g’ – use like halogen dimer-lamp ‘s’ – Soft Switch, lamp, when on/off power is supplied/deenergised smoothly (500msec) ‘k’ – Switch, lamp, when on/off power is supplied/deenergised immediately ‘l’ – LED Function, dimmable LED lamps ‘v’ – linear Function of dimming ‘-‘ – Channel disabled ‘+’ – Regular channel Example: dm=’skl-‘
def	integer 0-250	11-14	100	The default brightness level in case of a power reset (1..250). Example: def=250
min	integer 0-100	11-14	0	Minimum dimming level, example: min=10
max	integer 0-100	11-14	100	Maximum dimming level, example max=95
start	integer 0-100	11-14	0	The Start function is used for lamps that lack the minimal voltage to get turned on. If the set value is lower than the start value, the lamp is turned on at the start value and them the light is dimmed down to the set level. Example: start=60
force	integer 0-100	11-14	10	Time duration of the starting value (measured in milliseconds). Example: force=20
runtime	integer 0-60000	11-14	1000	Runtime is the speed of changing the brightness from ‘min’ to ‘max’ (measured in milliseconds). Example: runtime=1000
offset	integer (+/- 0…39)	39-46	'0'	sensor values offset; For example, offset is -3.8 : Example: hw="offset='-3.8'"
io	char[28]	98	io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'	Each char is responsible for the type of a particular channel '0' - led-dimmer '1' - halogen-dimmer '2' - linear-dimmer '3'..'6' - RGB-3..6 channels 'z' - WS2812B -string 'e' - led-button inverse 'd' - led-button 'c' - button inverse 'b' - button 's' - switch 'k' - contact inverse 'h' - contact 'l' - leak 'n' - Neptun 'v' - motion inverse 'm' - motion 'r' - thermo-resistor 't' - DALLAS '-' - none Example: io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'
hw	string	98	-	hw="...", where pwm_invert – PWM inverting [1, 0]; lbn_bright – brightness of led buttons, range (0 - 255); f – by default PWM frequency is 1000, range (1 - 5000). Example: 1hw="io='4---zdd----t--' pwm_invert=1 lbn_bright=255 f=1000"
Only for Metaforsa 3.plus
cfg	string	98	9600/8N1	cfg='SPEED/BPS', where SPEED – baud rate [1200..115200]; B – data length [7,8]; P – presence and type of parity bit [N(No parity),E(Even parity),O(Odd parity)]; S – stop bit length [1, 1.5 or 2]. Example: 1hw="cfg='9600/8N1'"
[Protocol]	string	98	—	Protocol setting is described by protocol parameter. The following protocols are supported: 'modbus', Modbus protocol, at the end of redirection the checksum CRC16(Modbus) is added; 'dmx', DMX protocol; 'CO2' for connecting Larnitech CO2 sensors; 'salda' for connecting Salda ventilation. Example: 1hw="cfg='9600/8N1' modbus"
echo	on; off	98	'off'	For settings check out and testing echo parameter can be used. Module echo-reply can be turned on or off with the help of this parameter.Echo parameter value: 'off' 'on' Example: 1hw="cfg='9600/8N1' echo='off'"

 1		<item addr="349:1" auto-period="600" cfgid="197" name="Lamp 1" type="lamp"/>
 2		<item addr="349:2" auto-period="600" cfgid="197" name="Lamp 2" type="lamp"/>
 3		<item addr="349:3" auto-period="600" cfgid="197" name="Lamp 3" type="lamp"/>
 4		<item addr="349:4" auto-period="600" cfgid="197" name="Lamp 4" type="lamp"/>
 5		<item addr="349:5" auto-period="600" cfgid="197" name="Lamp 5" type="lamp"/>
 6		<item addr="349:6" cfgid="197" name="Radiator" temperature-lag="0.2" type="valve-heating">
 7			<automation name="Eco" temperature-level="16"/>
 8			<automation name="Comfort" temperature-level="22"/>
 9			<automation name="Hot" temperature-level="25"/>
10		</item>
11		<item addr="349:7" cfgid="197" name="Radiator" temperature-lag="0.2" type="valve-heating">
12			<automation name="Eco" temperature-level="16"/>
13			<automation name="Comfort" temperature-level="22"/>
14			<automation name="Hot" temperature-level="25"/>
15		</item>
16		<item addr="349:8" cfgid="197" name="Radiator" temperature-lag="0.2" type="valve-heating">
17			<automation name="Eco" temperature-level="16"/>
18			<automation name="Comfort" temperature-level="22"/>
19			<automation name="Hot" temperature-level="25"/>
20		</item>
21		<item addr="349:9" cfgid="197" name="Jalousie" sub-type="120" type="jalousie"/>
22		<item addr="349:11" auto-period="600" cfgid="197" name="Dimmer 1" type="dimmer-lamp"/>
23		<item addr="349:12" auto-period="600" cfgid="197" name="Dimmer 2" type="dimmer-lamp"/>
24		<item addr="349:13" auto-period="600" cfgid="197" name="Dimmer 3" type="dimmer-lamp"/>
25		<item addr="349:14" auto-period="600" cfgid="197" name="Dimmer 4" type="dimmer-lamp"/>
26		<item addr="349:16" cfgid="197" name="Door 1" type="door-sensor"/>
27		<item addr="349:17" cfgid="197" name="Door 2" type="door-sensor"/>
28		<item addr="349:18" cfgid="197" name="Door 3" type="door-sensor"/>
29		<item addr="349:19" cfgid="197" name="Door 4" type="door-sensor"/>
30		<item addr="349:20" cfgid="197" name="Door 5" type="door-sensor"/>
31		<item addr="349:21" cfgid="197" name="Door 6" type="door-sensor"/>
32		<item addr="349:22" cfgid="197" name="Door 7" type="door-sensor"/>
33		<item addr="349:23" cfgid="197" name="Door 8" type="door-sensor"/>
34		<item addr="349:24" cfgid="197" name="Door 9" type="door-sensor"/>
35		<item addr="349:25" cfgid="197" name="Door 10" type="door-sensor"/>
36		<item addr="349:26" cfgid="197" name="Door 11" type="door-sensor"/>
37		<item addr="349:27" cfgid="197" name="Door 12" type="door-sensor"/>
38		<item addr="349:28" cfgid="197" name="Door 13" type="door-sensor"/>
39		<item addr="349:29" cfgid="197" name="Door 14" type="door-sensor"/>
40		<item addr="349:30" cfgid="197" name="Door 15" type="door-sensor"/>
41		<item addr="349:31" cfgid="197" name="Door 16" type="door-sensor"/>
42		<item addr="349:32" cfgid="197" name="Door 17" type="door-sensor"/>
43		<item addr="349:33" cfgid="197" name="Door 18" type="door-sensor"/>
44		<item addr="349:34" cfgid="197" name="Door 19" type="door-sensor"/>
45		<item addr="349:35" cfgid="197" name="Door 20" type="door-sensor"/>
46		<item addr="349:36" cfgid="197" name="Door 21" type="door-sensor"/>
47		<item addr="349:37" cfgid="197" name="Door 22" type="door-sensor"/>
48		<item addr="349:38" cfgid="197" name="Door 23" type="door-sensor"/>
49		<item addr="349:39" cfgid="197" name="Door 24" type="door-sensor"/>
50		<item addr="349:40" cfgid="197" name="Door 24" type="door-sensor"/>
51		<item addr="349:41" cfgid="197" name="Door 25" type="door-sensor"/>
52		<item addr="349:43" cfgid="197" name="IR receiver" type="ir-receiver"/>
53		<item addr="349:44" cfgid="197" name="RS485" type="com-port"/>
54		<item addr="349:90" cfgid="197" name="Current" system="yes" type="current-sensor"/>
55		<item addr="349:95" cfgid="197" name="Temperature" system="yes" type="temperature-sensor"/>
56		<item addr="349:96" cfgid="197" name="Temperature" system="yes" type="temperature-sensor"/>
57		<item addr="349:97" cfgid="197" name="Temperature" system="yes" type="temperature-sensor"/>
58		<item addr="349:98" cfgid="197" hw="out='LLLLLHHHB-' dm='LLLL' io='KKKKKKKKKKKKKKKKKKKKUKKKKKK-'" logic-ver="19" name="Temperature" sn="2533726919" system="yes" type="temperature-sensor"/>
59		<item addr="349:100" cfgid="197" name="RS232" type="com-port"/>