DW-DM04
DW-DM04.C | |||||||||
---|---|---|---|---|---|---|---|---|---|
| |||||||||
|
4-Х КАНАЛЬНЫЙ ДИММЕР
Этот модуль предназначен для плавной регулировки яркости осветительных приборов (не реактивной нагрузки). Тип диммера MOSFET, диммирование по заднему фронту. Как и все устройства Larnitech, диммер автоматически обнаруживается и настраивается при добавлении в систему. В диммере есть собственный логический модуль, выполняющий скрипты из базы обширной и постоянно пополняемой базы данных Larnitech для осуществления управления на основе распределённой логики, что гарантирует надёжность его работы. Расширенные установки работы светодиодных светильников обеспечивают более точную настройку, а режим мягкого включения увеличивает срок службы электроламп, дополнительно предоставляя комплексную защиту по ряду параметров.
Функции
- Нагрузка резистивного или ёмкостного типа на 4 канала. Каждый канал выдерживает до 500 Вт
- Работает с галогеновыми/светодиодными лампами
- Расширенные настройки управления светодиодными лампами
- Режим плавного включения ламп
- Защита от перегрузки
- Защита от перегрева
- Защита от короткого замыкания
- Plug and Play (модуль автоматически обнаруживается и настраивается системой при подключении)
- Встроенный логический блок
- Регулярные обновления системы
CAUTION! All work related to the installation, connection, setting up, service and support must be carried out by qualified personnel with sufficient skills and experience in working with electrical equipment. To avoid the risk of fire, electric shock, damage to the system and/or personal injury, the system installation and assembly must be performed in accordance with the instructions listed below:
- all connectivity work must be carried out with the power turned OFF;
- use appropriate tools and personal protection against electric shock;
- do not use damaged cables, wires and connectors;
- avoid folding the cables and wires;
- do not apply excessive force to the wires by kinking or pressing them too hard: the inner conductors of the cables and wires may get stripped or damaged;
- do not use the power socket with poor contacts to connect;
- do not exceed the load limit parameters specified in the manual;
- the supply conductors wire section is subject to the specifications for current density limit, insulation type and wire material. Light section can result in cable overheating and fire.
When the power is on, NEVER:
- connect/disconnect the connectors;
- open modules and sensors.
Overview
Example of connection
Module dimensions
Internal layout
Module parameters
Parameter name | Value |
---|---|
Dimming channels qty | 4 |
Input voltage | 100-240V AC, 50-60 Hz |
Current type | AC |
Max load per channel | 2.27A (500W at 220V) |
Max load per device | 7.27A (1600W at 220V) |
Dimmer type | MOSFET |
Dimming type | trailing edge |
Power supply | 11.5 … 27.5 V DC from CAN |
Max current(24V) | 35 mA |
Bus type | CAN (4-wire) |
Equipment installation type | DIN rail (EN 60715) |
Case material | ABS |
Protection | IP40 |
Temperature range | -10 … +50 °C |
Size | 4U, 69x102x58 mm |
Weight | 180 g |
Supported load types
Supported load type | Power | |
---|---|---|
Conventional incandescent lamps | 0-500W | |
Halogen light sources | 0-500W | |
LED lamps with dimming support | 0-500W | |
Energy saving lamps with dimming support | 0-500W | |
Electronic ballasts with dimming support | 0-500W |
Indication of module operation
Bootloader
Indicator | Status | Description |
---|---|---|
Device in bootloader | ||
Waiting for bootloader command | ||
Flashing firmware |
Firmware
Indicator | Status | Description |
---|---|---|
Identification | ||
Operational mode | ||
Error | ||
Lost connection to server | ||
Overheat | ||
No AC power | ||
RTC error |
Module installation and connection procedure
- Install the module in the switchboard on the DIN rail and fix it with the special latch on the module base.
- Connect the CAN connector.
- Connect the contacts (1-4).
- Configure the module using LT setup.
- Apply power to the load.
- Check all equipment for proper operation.
Module shut-off and deinstallation procedure
- Disconnect the power from the load.
- Disconnect the contacts (1-4).
- Disconnect the CAN connector.
- Remove the module from the DIN rail, releasing the latch at the bottom of the module base.
Dimmer workflow
Linear, LED and Halogen workflows
HW settings
Name | Type, range | SUBID | Default | Description |
---|---|---|---|---|
dm | char[4] | 98 | 'LLLL' | Each char is responsible for the type of a particular channel
Example: dm='skl-' |
def | integer 0-250 | 1-4 | 100 | The default brightness level in case of a power reset (1..250). Example: def=250 |
min | integer 0-100 | 1-4 | 0 | Minimum dimming level, example: min=10 |
max | integer 0-100 | 1-4 | 100 | Maximum dimming level, example max=95 |
start | integer 0-100 | 1-4 | 0 | The Start function is used for lamps that lack the minimal voltage to get turned on. If the set value is lower than the start value, the lamp is turned on at the start value and them the light is dimmed down to the set level. Example: start=60 |
force | integer 0-100 | 1-4 | 10 | Time duration of the starting value (measured in milliseconds). Example: force=20 |
runtime | integer 0-60000 | 1-4 | 1000 | Runtime is the speed of changing the brightness from 'min' to 'max' (measured in milliseconds). Example: runtime=1000 |
1<item addr="307:1" auto-period="600" cfgid="77" hw="def=200 min=30 max=88 start=35 force=20 runtime=1000 " name="Dimmer" type="dimer-lamp" uniq_id="51"/>
2<item addr="307:2" auto-period="600" cfgid="77" hw="min=20 max=90 " name="Dimmer" type="dimer-lamp" uniq_id="52"/>
3<item addr="307:3" auto-period="600" cfgid="77" name="Dimmer" type="dimer-lamp" uniq_id="53"/>
4<item addr="307:97" cfgid="77" name="Temperature" system="yes" type="temperature-sensor" uniq_id="55"/>
5<item addr="307:98" cfgid="77" hw="dm='++--'" name="Temperature" system="yes" type="temperature-sensor" uniq_id="56"/>