DW-DM02

DW-DM02.С
DW-DM02.С
Number of dimming channels
Output ports
Number of dimming channels	2
Max load per dimming channel	1.36A (300W at 220V)
Dimmer type	MOSFET
Supply voltage
Other
Supply voltage	11.5...27.5 V DC from CAN
Dimentions	4U, 69x100x58 mm

Other languages:

English • ‎русский

Revision:

A

/B

/C

2-Х КАНАЛЬНЫЙ ДИММЕР

Этот модуль предназначен для плавной регулировки яркости осветительных приборов (не реактивной нагрузки). Тип диммера MOSFET, диммирование по заднему фронту. Как и все устройства Larnitech, диммер автоматически обнаруживается и настраивается при добавлении в систему. В диммере есть собственный логический модуль, выполняющий скрипты из базы обширной и постоянно пополняемой базы данных Larnitech для осуществления управления на основе распределённой логики, что гарантирует надёжность его работы. Расширенные установки работы светодиодных светильников обеспечивают более точную настройку, а режим мягкого включения увеличивает срок службы электроламп, дополнительно предоставляя комплексную защиту по ряду параметров.

Features

R/C load type has 2 channels. Each channel supports up to 1000 W
Works with halogen /LED lights
Advanced LED light settings
Soft start mode
Overload protection
Overheating protection
Short-circuit protection
Plug and play (automatically detected and configured by the system)
Built-in logical unit
Regular system updates

CAUTION! All work related to the installation, connection, setting up, service and support must be carried out by qualified personnel with sufficient skills and experience in working with electrical equipment. To avoid the risk of fire, electric shock, damage to the system and/or personal injury, the system installation and assembly must be performed in accordance with the instructions listed below:

all connectivity work must be carried out with the power turned OFF;
use appropriate tools and personal protection against electric shock;
do not use damaged cables, wires and connectors;
avoid folding the cables and wires;
do not apply excessive force to the wires by kinking or pressing them too hard: the inner conductors of the cables and wires may get stripped or damaged;
do not use the power socket with poor contacts to connect;
do not exceed the load limit parameters specified in the manual;
the supply conductors wire section is subject to the specifications for current density limit, insulation type and wire material. Light section can result in cable overheating and fire.

When the power is on, NEVER:

connect/disconnect the connectors;
open modules and sensors.

Overview

DM02C VIEW.png

Example of connection

DM02C EXA.png

Module dimensions

DM02C DIM.png

Internal layout

DM02C IL.png

Module parameters

Parameter name	Value
Input channels qty
Input/output channels qty
0-10 input port quantity
Buttons
LED Buttons
Number of sensor inputs
Number of dry contact inputs
RS485 ports qty
RS232 ports qty
UART ports qty
M-BUS port quantity
Pulse inputs quantity
DALI ports qty
DALI-line voltage supply
Peak current of DALI-line power supply
Peak current in DALI-line
Maximum DALI devices quantity
Dimming channels qty	2
Output channels qty
0-10 output port quantity
Analog output channels qty
Output
Digital line maximum length
Discrete input channels qty
Digital input channels qty
Speakers
Max power output audio channel
Camera
IR lighting
Card reader
Connection type
Protocols
Backlight voltage
Load type
Dimmer load type
Supported sensors
Input voltage	100-240V AC, 50-60 Hz
Current type	AC
Adjustment type
Max load
Min load
Max load per channel	4.54A (1000W at 220V)
Max load per group
Max load per device	7.27A (1600W at 220V)
Control parameters
Angle of vision IR	°
Angle of motion	°
Temperature measuring range	°C
Humidity measuring range
Dimmer type	MOSFET
Dimming type	trailing edge
Voltage that may be applied to the input channels	100-240V AC, 50-60 Hz
Max output switching voltage
Max output switching current
Power supply	11.5 … 27.5 V DC from CAN
Max current(24V)	35 mA
Max current(13V)
Max detection distance
Max IR distance
Max BT distance
Max current
Relay
Data transfer speed
Permissible section of power supply cable to connect in socket:
Sensors VCC output
Sensors max VCC current
R1-R2 inputs max current
Push-button/reed switches line recommended length
Temperature sensor line max length
Sensor cable length
Sensors line max length
Bus type	CAN (4-wire)
Compatible with
Output voltage
Output current
Equipment installation type	DIN rail (EN 60715)
Mounting
Max cabel lenght
Case material	ABS
Protection	IP40
Temperature range	-10 … +50 °C
Size	4U, 69x102x58 mm
Weight	180g

Supported load types

CAUTION! Do not overload the dimmer in order to avoid it overheating and breaking down. Use it safely by following the parameters provided in the parameters table. Only the kinds of load and load power options outlined in the compatible devices table are to be used with this dimmer.

Supported load type		Power
	Conventional incandescent lamps	0-1000W
	Halogen light sources	0-1000W
	LED lamps with dimming support	0-1000W
	Energy saving lamps with dimming support	0-1000W
	Electronic ballasts with dimming support	0-1000W

Indication of module operation

Bootloader

Indicator	Status	Description
		Device in bootloader
		Waiting for bootloader command
		Flashing firmware

Firmware

Indicator	Status	Description

		Network configuration
		Identification
	Operational mode
	Operational mode
Error
		Lost connection to server
		Overheat
		Overload
		No AC power
	RTC error
Activity
	CAN activity
	OW activity
	RS-485 activity
	Ethernet activity

Module installation and connection procedure

Install the module in the switchboard on the DIN rail and fix it with the special latch on the module base.
Connect the CAN connector.
Connect the contacts (1-2).
Configure the module using LT setup.
Apply power to the load.
Check all equipment for proper operation.

Module shut-off and deinstallation procedure

Disconnect the power from the load.
Disconnect the contacts (1-2).
Disconnect the CAN connector.
Remove the module from the DIN rail, releasing the latch at the bottom of the module base.

Dimmer workflow

Linear, LED and Halogen workflows

HW settings

Name	Type, range	SUBID	Default	Description
dm	char[2]	98	'LL'	Each char is responsible for the type of a particular channel 'g' – use like halogen dimer-lamp 's' – Soft Switch, lamp, when on/off power is supplied/deenergised smoothly (500msec) 'k' – Switch, lamp, when on/off power is supplied/deenergised immediately 'l' – LED Function, dimmable LED lamps 'v' – linear Function of dimming 'b' – blinds 'f' – fancoil '-' – Channel disabled '+' – Regular channel Example: dm='sk'
def	integer 0-250	1-2	100	The default brightness level in case of a power reset (1..250). Example: def=250
min	integer 0-100	1-2	0	Minimum dimming level, example: min=10
max	integer 0-100	1-2	100	Maximum dimming level, example max=95
start	integer 0-100	1-2	0	The Start function is used for lamps that lack the minimal voltage to get turned on. If the set value is lower than the start value, the lamp is turned on at the start value and them the light is dimmed down to the set level. Example: start=60
force	integer 0-100	1-2	10	Time duration of the starting value (measured in milliseconds). Example: force=20
runtime	integer 0-60000	1-2	1000	Runtime is the speed of changing the brightness from 'min' to 'max' (measured in milliseconds). Example: runtime=1000

1<item addr="307:1" auto-period="600" cfgid="77" hw="def=200 min=30 max=88 start=35 force=20 runtime=1000 " name="Dimmer" type="dimer-lamp" uniq_id="51"/>
2<item addr="307:2" auto-period="600" cfgid="77" hw="min=20 max=90 " name="Dimmer" type="dimer-lamp" uniq_id="52"/>
3<item addr="307:3" auto-period="600" cfgid="77"  name="Dimmer" type="dimer-lamp" uniq_id="53"/>
4<item addr="307:97" cfgid="77" name="Temperature" system="yes" type="temperature-sensor" uniq_id="55"/>
5<item addr="307:98" cfgid="77" hw="dm='+-'" name="Temperature" system="yes" type="temperature-sensor" uniq_id="56"/>