DW-SW16

Revision:

A

A/B

/B

/C

DW-SW16.C
Input ports Number of inputs 16 Number of buttons 15 Number of LED buttons 8
Other Supply voltage 11.5...27.5 V DC Dimentions 2U, 36x102x58 mm

16-ТИ КАНАЛЬНЫЙ АДАПТЕР ДЛЯ КНОПОК/16-канальный модуль входов

Модуль может поддерживать до 15-ти кнопок/герконов или до 8-ми светодиодных кнопок

Функции

• Поддержка до 15-ти кнопок/герконов
• Поддержка до 8-ми светодиодных кнопок
• Поддержка одиночного/двойного/тройного/многократного нажатия.
  Поддержка до 4-х различных действий для каждой кнопки
• Линейная защита от помех

CAUTION! All work related to the installation, connection, setting up, service and support must be carried out by qualified personnel with sufficient skills and experience in working with electrical equipment. To avoid the risk of fire, electric shock, damage to the system and/or personal injury, the system installation and assembly must be performed in accordance with the instructions listed below:

• all connectivity work must be carried out with the power turned OFF;
• use appropriate tools and personal protection against electric shock;
• do not use damaged cables, wires and connectors;
• avoid folding the cables and wires;
• do not apply excessive force to the wires by kinking or pressing them too hard: the inner conductors of the cables and wires may get stripped or damaged;
• do not use the power socket with poor contacts to connect;
• do not exceed the load limit parameters specified in the manual;
• the supply conductors wire section is subject to the specifications for current density limit, insulation type and wire material. Light section can result in cable overheating and fire.

When the power is on, NEVER:

• connect/disconnect the connectors;
• open modules and sensors.

Overview

Module dimensions

Connector

Led button scheme

Connection of buttons/LED buttons

Module parameters

Parameter name	Value
Input channels qty	16
Input/output channels qty
0-10 input port quantity
Buttons	15
LED Buttons	8
Number of sensor inputs
Number of dry contact inputs
RS485 ports qty
RS232 ports qty
UART ports qty
M-BUS port quantity
Pulse inputs quantity
DALI ports qty
DALI-line voltage supply
Peak current of DALI-line power supply
Peak current in DALI-line
Maximum DALI devices quantity
Dimming channels qty
Output channels qty
0-10 output port quantity
Analog output channels qty
Output
Digital line maximum length
Discrete input channels qty
Digital input channels qty
Speakers
Max power output audio channel
Camera
IR lighting
Card reader
Connection type
Protocols
Backlight voltage	3V
Load type
Dimmer load type
Supported sensors
Input voltage
Current type
Adjustment type
Max load
Min load
Max load per channel
Max load per group
Max load per device
Control parameters
Angle of vision IR	°
Angle of motion	°
Temperature measuring range	°C
Humidity measuring range
Dimmer type
Dimming type
Voltage that may be applied to the input channels
Max output switching voltage
Max output switching current
Power supply	11.5 … 27.5 V DC from CAN
Max current(24V)	45 mA
Max current(13V)
Max detection distance
Max IR distance
Max BT distance
Max current
Relay
Data transfer speed
Permissible section of power supply cable to connect in socket:
Sensors VCC output
Sensors max VCC current
R1-R2 inputs max current
Push-button/reed switches line recommended length	30m
Temperature sensor line max length
Sensor cable length
Sensors line max length
Bus type	CAN (4-wire)
Compatible with
Output voltage
Output current
Equipment installation type	DIN rail (EN 60715)
Mounting
Max cabel lenght
Case material	ABS
Protection	IP40
Temperature range	-10 … +50 °C
Size	2U, 36x102x58 mm
Weight	75g

* -

** -

*** -

1 -

2 -

3 -

Indication of module operation

Bootloader

Indicator	Status	Description
		Device in bootloader
		Downloading firmware
		Flashing firmware

Firmware

Indicator	Status	Description
		Network configuration
		Identification
	Operational mode
	Operational mode
Error
		Lost connection to server
		Overheat
	Overload
	No AC power
	RTC error
Activity
		Key pressed
	OW activity
	RS-485 activity
	Ethernet activity

Module installation and connection procedure

1. Install the module in the switchboard on the DIN rail and fix it with the special latch on the module base.
2. Connect the X1 connector.
3. Connect the CAN connector.
4. Configure the module using LT setup.
5. Check all equipment for proper operation.

Module shut-off and deinstallation procedure

1. Disconnect the CAN connector.
2. Disconnect the X1 connector.
3. Remove the module from the DIN rail, releasing the latch at the bottom of the module base.

HW settings

Name	Type, range	SUBID	Default	Description
in	char[16]	98	'BBBBBBBBGGGGGGGG'	Each char is responsible for the type of a particular channel 'B'-Button, button of bell a type; 'C'-Inverted button, inverse button of a bell type (for normally-closed); 'D'-Backlit button, illuminated button; 'E'-Inverted backlit button, inverse illuminated button; 'S'-Switch, fixed switch; 'K'-Contact, reed contact; 'H'-Inverted contact, invers reed contact; 'G'-GND, is used as earthing; '-'-none, nothing is connected. Example: in='DEHHHHBB- -CCSSSG'

 1<item addr="441:11" cfgid="55" name="Switch" type="switch" uniq_id="4628"/>
 2<item addr="441:12" cfgid="55" name="Switch" type="switch" uniq_id="4629"/>
 3<item addr="441:13" cfgid="55" name="Switch" type="switch" uniq_id="4630"/>
 4<item addr="441:14" cfgid="55" name="Switch" type="switch" uniq_id="4631"/>
 5<item addr="441:15" cfgid="55" name="Switch" type="switch" uniq_id="4632"/>
 6<item addr="441:16" cfgid="55" name="Switch" type="switch" uniq_id="4633"/>
 7<item addr="441:17" cfgid="55" name="Switch" type="switch" uniq_id="4634"/>
 8<item addr="441:18" cfgid="55" name="Door" type="door-sensor" uniq_id="4637"/>
 9<item addr="441:19" cfgid="55" name="Switch" type="switch" uniq_id="4638"/>
10<item addr="441:20" cfgid="55" name="Switch" type="switch" uniq_id="4639"/>
11<item addr="441:25" cfgid="55" name="Switch" type="switch" uniq_id="4640"/>
12<item addr="441:98" cfgid="55" hw="in='BBDDEESHBB----BG'" name="Temperature" system="yes" type="temperature-sensor" uniq_id="4636"/>