DW-010

DW-010.C
DW-010.C
Number of switched channels
Output ports
Number of switched channels	4
Number of inputs
Input ports
Number of inputs	2
Supply voltage
Other
Supply voltage	11.5...27.5 V DC
Dimentions	2U, 36x97x58 mm

Revision:

A

/C

MODULE FOR DEVICES WITH 0-10V INPUT OR OUTPUT

This module allows connecting devices with 0-10V input or output interfaces to the Smart Home system.

CAUTION! All work related to the installation, connection, setting up, service and support must be carried out by qualified personnel with sufficient skills and experience in working with electrical equipment. To avoid the risk of fire, electric shock, damage to the system and/or personal injury, the system installation and assembly must be performed in accordance with the instructions listed below:

all connectivity work must be carried out with the power turned OFF;
use appropriate tools and personal protection against electric shock;
do not use damaged cables, wires and connectors;
avoid folding the cables and wires;
do not apply excessive force to the wires by kinking or pressing them too hard: the inner conductors of the cables and wires may get stripped or damaged;
do not use the power socket with poor contacts to connect;
do not exceed the load limit parameters specified in the manual;
the supply conductors wire section is subject to the specifications for current density limit, insulation type and wire material. Light section can result in cable overheating and fire.

When the power is on, NEVER:

connect/disconnect the connectors;
open modules and sensors.

Overview

Module dimensions

Connection of 6 0-10V devices

Module parameters

Parameter name	Value
Input channels qty	2
Input/output channels qty
0-10 input port quantity
Buttons
LED Buttons
Number of sensor inputs
Number of dry contact inputs
RS485 ports qty
RS232 ports qty
UART ports qty
M-BUS port quantity
Pulse inputs quantity
DALI ports qty
DALI-line voltage supply
Peak current of DALI-line power supply
Peak current in DALI-line
Maximum DALI devices quantity
Dimming channels qty
Output channels qty	4
0-10 output port quantity
Analog output channels qty
Output
Digital line maximum length
Discrete input channels qty
Digital input channels qty
Speakers
Max power output audio channel
Camera
IR lighting
Card reader
Connection type
Protocols
Backlight voltage
Load type
Dimmer load type
Supported sensors
Input voltage
Current type
Adjustment type
Max load
Min load
Max load per channel	15mA
Max load per group
Max load per device
Control parameters
Angle of vision IR	°
Angle of motion	°
Temperature measuring range	°C
Humidity measuring range
Dimmer type
Dimming type
Voltage that may be applied to the input channels
Max output switching voltage
Max output switching current
Power supply	11.5 … 27.5 V DC from CAN
Max current(24V)	50 mA
Max current(13V)
Max detection distance
Max IR distance
Max BT distance
Max current
Relay
Data transfer speed
Permissible section of power supply cable to connect in socket:
Sensors VCC output
Sensors max VCC current
R1-R2 inputs max current
Push-button/reed switches line recommended length	30m
Temperature sensor line max length
Sensor cable length
Sensors line max length
Bus type	CAN (4-wire)
Compatible with
Output voltage
Output current
Equipment installation type	DIN rail (EN 60715)
Mounting
Max cabel lenght
Case material	ABS
Protection	IP40
Temperature range	-10 … +50 °C
Size	2U, 36x97x58 mm
Weight	130g

Indication of module operation

Bootloader

Indicator	Status	Description
		Device in bootloader
		Downloading firmware
		Flashing firmware

Firmware

Indicator	Status	Description

		Network configuration
		Identification
	Operational mode
	Operational mode
Error
		Lost connection to server
		Overheat
	Overload
	No AC power
	RTC error
Activity
	CAN activity
	OW activity
	RS-485 activity
	Ethernet activity

Module installation and connection procedure

Install the module in the switchboard on the DIN rail and fix it with the special latch on the module base.
Connect the input/output connectors.
Connect the CAN connector.
Configure the module using LT setup.
Check all equipment for proper operation.

Module shut-off and deinstallation procedure

Disconnect the CAN connector.
Disconnect the input/output connectors.
Remove the module from the DIN rail, releasing the latch at the bottom of the module base.

HW settings

Name	Type, range	SUBID	Default	Description
def	integer 0-250	1-4	100	The default brightness level in case of a power reset (1..250). Example: def=250
min	integer 0-100	1-4	0	Minimum dimming level, example: min=10
max	integer 0-100	1-4	100	Maximum dimming level, example max=95
start	integer 0-100	1-4	0	The Start function is used for lamps that lack the minimal voltage to get turned on. If the set value is lower than the start value, the lamp is turned on at the start value and them the light is dimmed down to the set level. Example: start=60
force	integer 0-100	1-4	10	Time duration of the starting value (measured in milliseconds). Example: force=20
runtime	integer 0-60000	1-4	1000	Runtime is the speed of changing the brightness from ‘min’ to ‘max’ (measured in milliseconds). Example: runtime=1000
dm	char[4]	98	'vvvv'	Each char is responsible for the type of a particular channel 'g' – use like halogen dimmer-lamp 's' – Soft Switch, lamp, when on/off power is supplied/deenergised smoothly (500msec) 'k' – Switch, lamp, when on/off power is supplied/deenergised immediately 'l' – LED Function, dimmable LED lamps 'v' – linear Function of dimming '-' – Channel disabled '+' – Regular channel Example: dm='skl-'

1<item addr="416:1" auto-period="600" cfgid="144" name="Dimmer 1" type="dimmer-lamp"/>
2<item addr="416:2" auto-period="600" cfgid="144" name="Dimmer 2" type="dimmer-lamp"/>
3<item addr="416:3" auto-period="600" cfgid="144" name="Dimmer 3" type="dimmer-lamp"/>
4<item addr="416:4" auto-period="600" cfgid="144" name="Dimmer 4" type="dimmer-lamp"/>
5<item addr="416:31" cfgid="144" name="Voltage" system="yes" type="voltage-sensor"/>
6<item addr="416:32" cfgid="144" name="Voltage" system="yes" type="voltage-sensor"/>
7<item addr="416:97" cfgid="144" name="Temperature" system="yes" type="temperature-sensor"/>
8<item addr="416:98" cfgid="144" logic-ver="19" name="Temperature"  system="yes" type="temperature-sensor"/>