DW-LC10

DW-LC10.C
DW-LC10.C
Number of switched channels
Output ports
Number of switched channels	10
Peak load	16A
Supply voltage
Other
Supply voltage	11.5...27.5 V DC
Dimentions	4U, 69x115x58 mm

Other languages:

English • ‎русский

Revision:

A

/B

/C

10-ТИ КАНАЛЬНОЕ РЕЛЕ

Модуль предназначен для коммутации цепей постоянного и переменного тока большой мощности. Применяется для управления освещением, эл. розетками, фанкойлами, замками, жалюзи/воротами.

Функции

Управление широким спектром устройств:
- Освещение
- Клапаны отопления НЗ/НО
- Жалюзи
- 1- или 2-х полюсные ворота
- 1- или 2-х полюсные клапаны
- Замки NC/NO
- Фанкойлы
Реле с контактами AgSnO2 рассчитаны на постоянную нагрузку 16 А и пиковую нагрузку до 120 А 20 мс
Переключение реле с низким уровнем шума
Встроенный логический модуль
Поддержка технологии Plug&Play
Регулярные обновления программного обеспечения

CAUTION! All work related to the installation, connection, setting up, service and support must be carried out by qualified personnel with sufficient skills and experience in working with electrical equipment. To avoid the risk of fire, electric shock, damage to the system and/or personal injury, the system installation and assembly must be performed in accordance with the instructions listed below:

all connectivity work must be carried out with the power turned OFF;
use appropriate tools and personal protection against electric shock;
do not use damaged cables, wires and connectors;
avoid folding the cables and wires;
do not apply excessive force to the wires by kinking or pressing them too hard: the inner conductors of the cables and wires may get stripped or damaged;
do not use the power socket with poor contacts to connect;
do not exceed the load limit parameters specified in the manual;
the supply conductors wire section is subject to the specifications for current density limit, insulation type and wire material. Light section can result in cable overheating and fire.

When the power is on, NEVER:

connect/disconnect the connectors;
open modules and sensors.

Изображение модуля

Пример подключения

Размеры модуля

Параметры модуля

Parameter name	Value
Input channels qty
Input/output channels qty
0-10 input port quantity
Buttons
LED Buttons
Number of sensor inputs
Number of dry contact inputs
RS485 ports qty
RS232 ports qty
UART ports qty
M-BUS port quantity
Pulse inputs quantity
DALI ports qty
DALI-line voltage supply
Peak current of DALI-line power supply
Peak current in DALI-line
Maximum DALI devices quantity
Dimming channels qty
Output channels qty
0-10 output port quantity
Analog output channels qty
Output
Digital line maximum length
Discrete input channels qty
Digital input channels qty
Speakers
Max power output audio channel
Camera
IR lighting
Card reader
Connection type
Protocols
Backlight voltage
Load type
Dimmer load type
Supported sensors
Input voltage
Current type
Adjustment type
Max load
Min load
Max load per channel
Max load per group
Max load per device
Control parameters
Angle of vision IR	°
Angle of motion	°
Temperature measuring range	°C
Humidity measuring range
Dimmer type
Dimming type
Voltage that may be applied to the input channels
Max output switching voltage
Max output switching current
Power supply
Max current(24V)
Max current(13V)
Max detection distance
Max IR distance
Max BT distance
Max current
Relay
Data transfer speed
Permissible section of power supply cable to connect in socket:
Sensors VCC output
Sensors max VCC current
R1-R2 inputs max current
Push-button/reed switches line recommended length
Temperature sensor line max length
Sensor cable length
Sensors line max length
Bus type
Compatible with
Output voltage
Output current
Equipment installation type
Mounting
Max cabel lenght
Case material
Protection
Temperature range	°C
Size
Weight

Подключение реле

Внимание! Перед подачей питания на модуль необходимо правильно настроить выходы в приложении. Неправильно настроенные контакты могут привести к одновременной подаче питания на оба канала, что приведет к выходу модуля из строя и/или отказу подключенного к нему оборудования, и даже к возгоранию. Если в данной группе после подключения к ней привода штор/жалюзи/ставней с низковольтным управлением или привода ворот остаются свободные (неиспользуемые) каналы, то эти каналы необходимо оставить неиспользованными. (Не подключайте к ним другие устройства!)

Подключение термореле освещения/электрического контактора/отопления

Пример HW для этой конфигурации

1hw="out='LLL-------'"

Подключение устройства с высокой нагрузкой

	Рекомендуемые контакторы: ABB серии ESB Schneider Acti 9 серии iCT Hager серии ESC.

Подключение реле штор/жалюзи/ставней с регулировкой усилия 220 В

Пример HW для этой конфигурации

1hw="out='B---------'"

Подключение привода штор/жалюзи/ставней с низковольтным управлением

Пример HW для этой конфигурации

1hw="out='B---------'"

Подключение однополюсного привода ворот

Пример HW для этой конфигурации

1hw="out='X---------'"

Подключение двухполюсного привода ворот

Пример HW для этой конфигурации

1hw="out='G---------'"

Connection of single-pole water/gas supply valve

Sample HW for this configuration

1hw="out='R---------'"

Connection of double-pole water/gas supply valve

Sample HW for this configuration

1hw="out='V---------'"

Connection of fancoil control unit

Sample HW for this configuration

1hw="out='FFF-------'"

Indication of module operation

Bootloader

Indicator	Status	Description
		Device in bootloader
		Downloading firmware
		Flashing firmware

Firmware

Indicator	Status	Description

		Network configuration
		Identification
	Operational mode
	Operational mode
Error
		Lost connection to server
		Overheat
	Overload
	No AC power
	RTC error
Activity
	CAN activity
	OW activity
	RS-485 activity
	Ethernet activity

Module installation and connection procedure

Install the module in the switchboard on the DIN rail and fix it with the special latch on the module base.
Connect the CAN connector.
Connect the channels (1-10).
Configure the module using LT setup.
Apply power to the load.
Check all equipment for proper operation.

Module shut-off and deinstallation procedure

Disconnect the power from the load.
Disconnect the channels (1-10).
Disconnect the CAN connector.
Remove the module from the DIN rail, releasing the latch at the bottom of the module base.

HW settings

Name	Type, range	SUBID	Default	Description
runtime	integer 0-100	1-10	15	runtime is the open/close time in seconds, is used for jalousie, gate, valve(2 pole); Example: runtime=15
runtimeopen	integer 0-60000	Blinds subId	–	Runtimeopen is the open time in milliseconds, is used for blinds; Example: runtimeopen=15000
runtimeclose	integer 0-60000	Blinds subId	–	Runtimeclose is the close time in milliseconds, is used for blinds; Example: runtimeclose=15000
hold	integer 0-10000	1-10	500	hold is the bridging time in miliseconds, is used for gate and jalousie (by default hold is the same as runtime), lock; Example: hold=3500
def	string 'ON'	1-10	'OFF'	def is the element status is set after restart, is used for lamp, heating, valve(1 pole); Example: def='ON'
stop	Char ‘R’	1-9	–	(for 2-pole gate and blinds) If it is declared then by Stop command during the motion, the same impulse appears as it was at the beginning of the motion. Pole, an which the stop-impules is formed, is defined by the parameter Stop value. If it is ‘r’ or ‘R’ then stop-impulse is produced on the opposite to the start-impulse pole. If any other value is delcared (e.g., ‘d’ ) then the stop-impulse is on the same pole. If a Runtime passed after the beginning of the motion then the stop-impulse is not formed. Example: stop=’r’
out	char[10]	98	'LLLLLLLLLL'	Each char is responsible for the type of a particular channel 'L'-Lamp; 'M'-Lamp Inverse; 'J'-Heating NO, valve-heating, normally open; 'H'-Heating NC, valve-heating, normally closed; 'B'-Blinds (2 pole), jalousie/curtains; 'C'-Blinds Inverse (2 pole), jalousie/curtains, invert open-close; 'G'-Gate (2 pole), 2 pole gate; 'D'-Gate (2 pole) Inverse, 2 pole gate, invert open-close; 'X'-Gate (1 pole /short press), 1 pole gate; 'Z'-Gate (1 pole) Inverse, 1 pole gate, invert open-close; 'V'-Valve (2 pole), 2 pole valve; 'W'-Valve (2 pole) Inverse, 2 pole valve, invert open-close; 'R'-Valve (1 pole), 1 pole valve,; 'S'-Valve (1 pole) Inverse, 1 pole valve, invert open-close; 'K'-Lock (short press); 'N'-Lock (short press) Inverse; 'P'-Blinds (2 pole); 'O'-Blinds Inverse (2 pole), invert open-close; 'F'-FanCoil. Group1 (Lamp Toggle). For fancoil speed control; 'E'-FanCoil. Group2 (Lamp Toggle). For fancoil speed control; 'Q'-FanCoil. Group3 (Lamp Toggle). For fancoil speed control; 'U'-FanCoil. Group4 (Lamp Toggle). For fancoil speed control; 'I'-FanCoil. Group5 (Lamp Toggle). For fancoil speed control; '-'-none, nothing is connected. Example: out='BGLKMVX'

 1<item addr="300:1" cfgid="98" hw="runtime=60" name="Jalousie" sub-type="120" type="jalousie" uniq_id="117"/>
 2<item addr="300:3" auto-period="600" cfgid="98" hw="def='ON'" name="Lamp" type="lamp" uniq_id="110"/>
 3<item addr="300:4" cfgid="98" hw="runtime=30" name="Gate" sub-type="120" type="gate" uniq_id="118"/>
 4<item addr="300:6" auto-period="600" cfgid="98" hw="hold=5000" name="Lamp" type="lamp" uniq_id="113"/>
 5<item addr="300:7" cfgid="98" hw="def='ON'" name="Radiator" type="valve-heating" uniq_id="119">
 6    <automation name="Eco" temperature-level="16" uniq_id="120"/>
 7    <automation name="Comfort" temperature-level="22" uniq_id="121"/>
 8    <automation name="Hot" temperature-level="25" uniq_id="122"/>
 9</item>
10<item addr="300:8" cfgid="98" hw="def='ON'" name="Radiator" type="valve-heating" uniq_id="123">
11    <automation name="Eco" temperature-level="16" uniq_id="124"/>
12    <automation name="Comfort" temperature-level="22" uniq_id="125"/>
13    <automation name="Hot" temperature-level="25" uniq_id="126"/>
14</item>
15<item addr="300:10" cfgid="98" hw="hold=2000" name="Gate" sub-type="120" type="gate" uniq_id="127"/>
16<item addr="300:97" cfgid="98" name="Temperature" system="yes" type="temperature-sensor" uniq_id="106"/>
17<item addr="300:98" cfgid="98" hw="out='BLGKHJ-X'" name="Temperature" system="yes" type="temperature-sensor" uniq_id="107"/>

DW-LC10

Contents

10-ТИ КАНАЛЬНОЕ РЕЛЕ

Функции

Изображение модуля

Пример подключения

Размеры модуля

Параметры модуля

Рекомендации по подключению

Подключение реле

Подключение термореле освещения/электрического контактора/отопления

Подключение устройства с высокой нагрузкой

Подключение реле штор/жалюзи/ставней с регулировкой усилия 220 В

Подключение привода штор/жалюзи/ставней с низковольтным управлением

Подключение однополюсного привода ворот

Подключение двухполюсного привода ворот

Connection of single-pole water/gas supply valve

Connection of double-pole water/gas supply valve

Connection of fancoil control unit

Indication of module operation

Bootloader

Firmware

Module installation and connection procedure

Module shut-off and deinstallation procedure

HW settings