Настройка роутера

Перед началом работы убедитесь, что настройки роутера соответствуют следующим требованиям:

• Сетевые настройки модуля DE-MG/Metaforsa соответствуют настройкам вашего роутера (IP-адрес по умолчанию 192.168.1.111/255.255.255.0);
• IP-адрес модуля DE-MG/Metaforsa выходит за пределы диапазона IP-адресов, которые предоставляет DHCP-сервер вашего роутера.

Если сетевые настройки модуля DE-MG/Metaforsa не совпадают с настройками вашего роутера, необходимо выполнить одно из следующих действий:

• Изменить сетевые настройки роутера в соответствии с настройками модуля DE-MG/Metaforsa;
• Изменить сетевые настройки модуля DE-MG/Metaforsa с помощью ПК (необходим порт Ethernet);
• Изменить сетевые настройки модуля DE-MG/Metaforsa с помощью роутера.

Changing the network settings of the router

1. Go to the 'Router settings' page (ZyXEL Keenetic router is used as an example).
2. Go to the local network settings menu and set the IP address of the router to 192.168.1.1, set the network mask to 255.255.255.0:
3. Go to the DHCP server Settings section and make sure that the IP address of DE-MG/Metaforsa is not in the range of IP addresses that are shown. Change the settings if necessary:

Changing of DE-MG/Metaforsa network settings with the help of a router

1. Save the current network settings of the router.
2. Change the router settings according to the chapter Changing the router network settings, which can be found in this instruction.
3. Open the DE-MG/Metaforsa module control panel in the browser (http://192.168.1.111/).
4. Go to the Settings tab -> Network and press the IP Setup button.
   
5. In the new window, type the new network settings, according to the default settings of your router. Save them. Examples:
   • IP 192.168.0.111
   • Mask 255.255.255.0
   • GW 192.168.0.1
   • DNS 8.8.8.8
     
6. Restore the initial settings of your router.
7. Check if the settings are correct by opening DE-MG/Metaforsa module control panel, while using a different IP address.

Changing DE-MG/Metaforsa module network settings with the help of a PC

1. Connect the DE-MG/Metaforsa module directly into the network adapter of your computer.
2. Open Control Panel and go to the ‘Network and Internet’, then choose ‘Change adapter parameters’ in the left column.
3. Open the Properties of the appropriate network interface:
   
4. In the window that opens, go to the Properties of Internet Protocol Version 4 (TCP/IPv4):
   
5. Change the network settings that are shown in the window that opens.
6. Choose ‘Use the following IP address’ and put in the following settings: *IP address 192.168.1.10 *Subnet mask 255.255.255.0 *Default gateway (leave empty)
   
7. Choose ‘Use the following DNS server addresses’ and use the following settings:
   • Preferred DNS server 8.8.8.8
   • Alternate DNS server (leave empty).
8. Apply the settings that are shown.
9. Open DE-MG/Metaforsa module control panel in the browser (http://192.168.1.111/).
10. Go to Settings -> Network and press the IP Setup button:
    
11. In the new window type the new network settings, based on the basic settings of your router and save them. For example:
    • IP 192.168.0.111
    • Mask 255.255.255.0
    • GW 192.168.0.1
    • DNS 8.8.8.8
      
12. Restore the initial network settings of your computer.
13. Disconnect DE-MG/Metaforsa from the computer.
14. Connect DE-MG/Metaforsa, as well as your computer to the router.
15. Check if the settings are right by opening DE-MG/Metaforsa module control panel in the browser using a new IP address.