editor, Interface administrators, Administrators, translation-admin, translator
9,750
edits
Changes
Created page with "*'e' - inverzna led tipka *'d' - LED-gumb *'c' - inverzni gumb *'b' - gumb *'s' - stikalo *'k' - stik inverzno *'h' - stik *'l' - puščanje *'n' - Neptun *'v' - obratno giban..."
*'z' - WS2812B -niz
*'z' - WS2812B -niz
*'e' - led-button inverse
*'e' - inverzna led tipka
*'d' - led-button
*'d' - LED-gumb
*'c' - button inverse
*'c' - inverzni gumb
*'b' - button
*'b' - gumb
*'s' - switch
*'s' - stikalo
*'k' - contact inverse
*'k' - stik inverzno
*'h' - contact
*'h' - stik
*'l' - leak
*'l' - puščanje
*'n' - Neptun
*'n' - Neptun
*'v' - motion inverse
*'v' - obratno gibanje
*'m' - motion
*'m' - gibanje
*'r' - thermo-resistor
*'r' - termo-upor
*'t' - DALLAS
*'t' - DALLAS
*'-' - none
*'-' - nič
primer: io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'
|-
|-
|hw||string||98||-||hw="...", where
|hw||string||98||-||hw="...", kje
*pwm_invert – PWM inverting [1, 0];
*pwm_invert – obračanje PWM [1, 0];
*lbn_bright – brightness of led buttons, range (0 - 255);
*lbn_bright – svetlost LED gumbov, obseg (0 - 255);
*f – by default PWM frequency is 1000, range (1 - 5000).
*f – privzeta frekvenca PWM je 1000, razpon (1 - 5000).
primer:
<syntaxhighlight lang="xml" line>
<syntaxhighlight lang="xml" line>
hw="io='4---zdd----t--' pwm_invert=1 lbn_bright=255 f=1000"
hw="io='4---zdd----t--' pwm_invert=1 lbn_bright=255 f=1000"
</syntaxhighlight>
</syntaxhighlight>
|-
|-
|colspan="3"|'''Only for Metaforsa 3.plus'''
|colspan="3"|'''Samo za Metaforsa 3.plus'''
|-
|-
|cfg||string||98||9600/8N1||cfg='SPEED/BPS', where
|cfg||string||98||9600/8N1||cfg='SPEED/BPS', kje
*SPEED – baud rate [1200..115200];
*SPEED – hitrost prenosa [1200..115200];
*B – data length [7,8];
*B – dolžina podatkov [7,8];
*P – presence and type of parity bit [N(No parity),E(Even parity),O(Odd parity)];
*P – prisotnost in vrsta paritetnega bita [N(Brez parnosti),E(Soda parnost),O(Liha parnost)];
*S – stop bit length [1, 1.5 or 2].
*S – dolžina stop bita [1, 1,5 ali 2].
primer:
<syntaxhighlight lang="xml" line>
<syntaxhighlight lang="xml" line>
hw="cfg='9600/8N1'"
hw="cfg='9600/8N1'"
</syntaxhighlight>
</syntaxhighlight>
|-
|-
|[Protocol]||string||98||—||Protocol setting is described by protocol parameter. The following
|[Protocol]||string||98||—||Nastavitev protokola je opisana s parametrom protokola. Naslednji
podprti so protokoli:
*'modbus', Modbus protocol, at the end of redirection the checksum CRC16(Modbus) is added;
*'modbus', protokol Modbus, na koncu preusmeritve se doda kontrolna vsota CRC16(Modbus);
*'dmx', DMX protocol;
*'dmx', protokol DMX;
*'CO2' for connecting Larnitech CO2 sensors;
*'CO2' za priključitev senzorjev Larnitech CO2;
*'salda' for connecting Salda ventilation.
*'salda' za priklop prezračevanja Salda.
primer:
<syntaxhighlight lang="xml" line>
<syntaxhighlight lang="xml" line>
hw="cfg='9600/8N1' modbus"
hw="cfg='9600/8N1' modbus"
</syntaxhighlight>
</syntaxhighlight>
|-
|-
|echo||on; off||98||'off'||For settings check out and testing echo parameter can be used. Module
|echo||on; off||98||'off'||Za preverjanje nastavitev in testiranje odmevnega parametra je mogoče uporabiti. Modul
echo-reply can be turned on or off with the help of this parameter.Echo parameter value:
echo-reply lahko vklopite ali izklopite s pomočjo tega parametra. Vrednost parametra Echo:
*'off'
*'izklopljeno'
*'on'
*'on'
primer:
<syntaxhighlight lang="xml" line>
<syntaxhighlight lang="xml" line>
hw="cfg='9600/8N1' echo='off'"
hw="cfg='9600/8N1' echo='off'"