Changes

3,752 bytes added , 12:46, 15 January 2022

Created page with "Настройки плагина безопасности"

<languages/>
1. Open LT Setup, General tab, click on Plugins 
[[File:Screenshot 1.png|250px]] 
2. Find Security plugin, click on Enable button to launch it 
[[File:02.png|900px]] 
3. Then click on Configure button
[[File:03.png|900px]] 
4. Click on +Add zone, to set actions for alarm settings 
[[File:04.png|350px]] 
5. Zone name - any you like, but to understand what system/sensors you will use 
[[File:05.png|400px]] 
6. You can add different zones. All added scenarios will appear below 
[[File:06.png|300px]] 
7. Then click on +Add device button, to add responsible sensors for the action 
[[File:07.png|600px]] 
8. In pop-up window set sensor and settings for it and save changes 
*Device type - set Arm 
*Device - choose you sensor 
*Name - sensors name in security plugin 
*Recovery timeout - time in seconds, when sensor resets after an alarm is triggered, until the problem disappears (door closing, no movement) 
*Level for alarm - range of values 1-100 for motion sensors 
[[File:08.png|600px]] 
9. To watch, what the sensor is responsible for action, click on the folder. You can add some sensors into a zone 
For all other zones, identic procedure 
[[File:09.png|400px]] 
10. After settings of zones, you need to add at least one user, create a password, and set the permissions for the user 
Click on the Users tab, and then on +Add 
[[File:10.png|500px]] 
11. In pop-up window, made a settings for the user, and save changes 
[[File:11.png|250px]]
[[File:12.png|700px]] 
12. After the creation of the user, the Security plugin becomes available in-app 
Open the app, click on the wi-fi icon, then on the Security icon. Will open the window with pin code confirmation 
Enter the pin you created for user, and then Ok 
[[File:13.png|400px]]
[[File:14.png|300px]] 
13. In Home tab, you will see your zones, and after clicking on the right corner icon, the sensors that you set 
[[File:15.png|300px]] 
14. In Security tab, you will see the widget 
[[File:16.png|250px]] 
*ARM - full arming of the house with your zones 
[[File:17.png|300px]] 
*Partial ARM - you can choose one or some zones for arming 
[[File:18.png|350px]] 
*Disarm - disarming the house 
[[File:19.png|300px]] 
*Armed - house under protection 
[[File:20.png|300px]] 
*Alarm - when sensors are triggering, the widget will turn Red and push-notification sent to your phone 
[[File:21.png|350px]]
[[File:22.png|350px]] 
*To reset the sensors, click on Alarm button, Reset sensors and Ok 
[[File:23.png|350px]] 
15. Also, you can set the scenarios for the Partial arm. For that, you need to go settings of the Security plugin 
On your zone, click on +Add device 
[[File:24.png|600px]] 
16. In pop-up window, click on Device type - in drop-down list choose Arm 
New fields will be appears 
[[File:25.png|220px]] 
17. Click on +Add mode. In the new window, set any name you like, Save settings and your mode will appear below 
[[File:26.png|600px]] 
18. After that, you can set the mode for your zones. For example day/night, and Save settings 
[[File:27.png|250px]] 
19. Open app, enter in Security plugin, move to Partial arm 
Your modes will appear in the drop-down list 
[[File:28.png|350px]] 
20. Click on the mode you want to arm and then Ok. The system will be activated 
[[File:29.png|300px]] 
21. To see, what zones are actually enabled, click on the Home tab 
[[File:30.png|300px]] 
22. Do the same with another mode - Night, in our case. And your settings will be activated 
[[File:31.png|300px]] 
23. Check the settings in Home tab 
[[File:32.png|300px]]

Rusanov

editor, translation-admin, translator

4,754

edits

Changes

Security plugin settings/ru (view source)

Revision as of 12:46, 15 January 2022