Difference between revisions of "DW-LC07"

From Larnitech wiki page
Jump to navigation Jump to search
(Marked this version for translation)
 
(One intermediate revision by the same user not shown)
Line 1: Line 1:
 +
<languages/>
 +
<translate>
 +
<!--T:1-->
 
{{RevisionChanger | hasA = 1 | hasB = 1 | hasC = 1}}
 
{{RevisionChanger | hasA = 1 | hasB = 1 | hasC = 1}}
 
{{Infobox module
 
{{Infobox module
Line 14: Line 17:
 
}}
 
}}
  
==7-CHANNEL ACTUATOR==
+
==7-CHANNEL ACTUATOR== <!--T:2-->
  
 +
<!--T:3-->
 
This module is designed for high power AC/DC circuits commutation.
 
This module is designed for high power AC/DC circuits commutation.
 
Applicable for light, power sockets, for control of fan coil units, locks, blinds/gates.
 
Applicable for light, power sockets, for control of fan coil units, locks, blinds/gates.
  
==Features==
+
==Features== <!--T:4-->
 
*Control of a wide range of devices:
 
*Control of a wide range of devices:
 
**Lights
 
**Lights
Line 34: Line 38:
 
*Regular software updates
 
*Regular software updates
  
 +
<!--T:5-->
 
<div class="caution">
 
<div class="caution">
 
CAUTION! All work related to the installation, connection, setting up, service and support must be carried out by qualified personnel with sufficient skills and experience in working with electrical equipment.
 
CAUTION! All work related to the installation, connection, setting up, service and support must be carried out by qualified personnel with sufficient skills and experience in working with electrical equipment.
Line 50: Line 55:
 
</div>
 
</div>
  
==Overview==
+
==Overview== <!--T:6-->
  
 +
<!--T:7-->
 
[[File:LC07C VIEW.png|500px]]
 
[[File:LC07C VIEW.png|500px]]
  
==Example of connection==
+
==Example of connection== <!--T:8-->
  
 +
<!--T:9-->
 
[[File:LC07C EXA.png|500px]]
 
[[File:LC07C EXA.png|500px]]
  
==Module dimensions==
+
==Module dimensions== <!--T:10-->
  
 +
<!--T:11-->
 
[[File:LC07C DIMM.png|500px]]
 
[[File:LC07C DIMM.png|500px]]
  
==Module parameters==
+
==Module parameters== <!--T:12-->
  
 +
<!--T:13-->
 
{{ Mp
 
{{ Mp
 
| outqty          = 7
 
| outqty          = 7
Line 83: Line 92:
 
}}
 
}}
  
==Connectivity recommendations==
+
==Connectivity recommendations== <!--T:14-->
  
 +
<!--T:15-->
 
In order to protect the actuator and loads connected to it, installing a circuit breaker is recommended.
 
In order to protect the actuator and loads connected to it, installing a circuit breaker is recommended.
 
The nominal value of the circuit breaker should be calculated based on the maximum total load of connected
 
The nominal value of the circuit breaker should be calculated based on the maximum total load of connected
Line 92: Line 102:
 
for each load.
 
for each load.
  
==Connection of actuators==
+
==Connection of actuators== <!--T:16-->
  
 +
<!--T:17-->
 
<div class="caution"> Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
 
<div class="caution"> Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
 
If free (unused) channels remain in a given group after a curtain/jalousie/shutter actuator with low-voltage control or gate actuator has been connected to it, these channels need to be left unused. (Do not connect other devices to them!) </div>
 
If free (unused) channels remain in a given group after a curtain/jalousie/shutter actuator with low-voltage control or gate actuator has been connected to it, these channels need to be left unused. (Do not connect other devices to them!) </div>
  
===Connection of the lights/electric contactor/heating thermal actuator===
+
===Connection of the lights/electric contactor/heating thermal actuator=== <!--T:18-->
  
 +
<!--T:19-->
 
[[File:lamps.png|200px]]<br>
 
[[File:lamps.png|200px]]<br>
 
Sample HW for this configuration
 
Sample HW for this configuration
Line 105: Line 117:
 
</syntaxhighlight>
 
</syntaxhighlight>
  
===Connection of high load device===
+
===Connection of high load device=== <!--T:20-->
  
 +
<!--T:21-->
 
{| class="wikitable" style="width:800px";
 
{| class="wikitable" style="width:800px";
 
|-
 
|-
Line 115: Line 128:
 
|}
 
|}
  
===Connection of curtain/jalousie/shutter actuator with 220V force control===
+
===Connection of curtain/jalousie/shutter actuator with 220V force control=== <!--T:22-->
  
 +
<!--T:23-->
 
[[File:Pjalousie.png|200px]]<br>
 
[[File:Pjalousie.png|200px]]<br>
 
Sample HW for this configuration
 
Sample HW for this configuration
Line 123: Line 137:
 
</syntaxhighlight>
 
</syntaxhighlight>
  
===Connection of curtain/jalousie/shutter actuator with low-voltage control===
+
===Connection of curtain/jalousie/shutter actuator with low-voltage control=== <!--T:24-->
  
 +
<!--T:25-->
 
[[File:Ljalousie.png|200px]]<br>
 
[[File:Ljalousie.png|200px]]<br>
 
Sample HW for this configuration
 
Sample HW for this configuration
Line 131: Line 146:
 
</syntaxhighlight>
 
</syntaxhighlight>
  
===Connection of single-pole gate actuator===
+
===Connection of single-pole gate actuator=== <!--T:26-->
  
 +
<!--T:27-->
 
[[File:1pgate.png|200px]]<br>
 
[[File:1pgate.png|200px]]<br>
 
Sample HW for this configuration
 
Sample HW for this configuration
Line 139: Line 155:
 
</syntaxhighlight>
 
</syntaxhighlight>
  
===Connection of double-pole gate actuator===
+
===Connection of double-pole gate actuator=== <!--T:28-->
  
 +
<!--T:29-->
 
[[File:2pgate.png|200px]]<br>
 
[[File:2pgate.png|200px]]<br>
 
Sample HW for this configuration
 
Sample HW for this configuration
Line 147: Line 164:
 
</syntaxhighlight>
 
</syntaxhighlight>
  
===Connection of single-pole water/gas supply valve===
+
===Connection of single-pole water/gas supply valve=== <!--T:30-->
  
 +
<!--T:31-->
 
[[File:1pvalve.png|200px]]<br>
 
[[File:1pvalve.png|200px]]<br>
 
Sample HW for this configuration
 
Sample HW for this configuration
Line 155: Line 173:
 
</syntaxhighlight>
 
</syntaxhighlight>
  
===Connection of double-pole water/gas supply valve===
+
===Connection of double-pole water/gas supply valve=== <!--T:32-->
  
 +
<!--T:33-->
 
[[File:2pvalve.png|200px]]<br>
 
[[File:2pvalve.png|200px]]<br>
 
Sample HW for this configuration
 
Sample HW for this configuration
Line 163: Line 182:
 
</syntaxhighlight>
 
</syntaxhighlight>
  
===Connection of fancoil control unit===
+
===Connection of fancoil control unit=== <!--T:34-->
  
 +
<!--T:35-->
 
[[File:fancoil.png|200px]]<br>
 
[[File:fancoil.png|200px]]<br>
 
Sample HW for this configuration
 
Sample HW for this configuration
Line 171: Line 191:
 
</syntaxhighlight>
 
</syntaxhighlight>
  
==Indication of module operation==
+
==Indication of module operation== <!--T:36-->
 
===Bootloader===
 
===Bootloader===
 
{{indication| textBBB= Waiting for bootloader command}}
 
{{indication| textBBB= Waiting for bootloader command}}
Line 182: Line 202:
 
}}
 
}}
  
==Module installation and connection procedure==
+
==Module installation and connection procedure== <!--T:37-->
  
 +
<!--T:38-->
 
*Install the module in the switchboard on the DIN rail and fix it with the special latch on the module base.
 
*Install the module in the switchboard on the DIN rail and fix it with the special latch on the module base.
 
*Connect the CAN connector.
 
*Connect the CAN connector.
Line 191: Line 212:
 
*Check all equipment for proper operation.
 
*Check all equipment for proper operation.
  
==Module shut-off and deinstallation procedure==
+
==Module shut-off and deinstallation procedure== <!--T:39-->
  
 +
<!--T:40-->
 
*Disconnect the power from the load.
 
*Disconnect the power from the load.
 
*Disconnect the channels (1-7).
 
*Disconnect the channels (1-7).
Line 198: Line 220:
 
*Remove the module from the DIN rail, releasing the latch at the bottom of the module base.
 
*Remove the module from the DIN rail, releasing the latch at the bottom of the module base.
  
==HW settings==
+
==HW settings== <!--T:41-->
 
{|class="wikitable"
 
{|class="wikitable"
 
|-
 
|-
Line 243: Line 265:
 
|}
 
|}
  
 +
<!--T:42-->
 
<syntaxhighlight lang="xml" line>
 
<syntaxhighlight lang="xml" line>
 
<item addr="300:1" cfgid="47" hw="runtime=60" name="Jalousie" sub-type="120" type="jalousie" uniq_id="117"/>
 
<item addr="300:1" cfgid="47" hw="runtime=60" name="Jalousie" sub-type="120" type="jalousie" uniq_id="117"/>
Line 256: Line 279:
 
<item addr="300:98" cfgid="47" hw="out='BLGKH'" name="Temperature" system="yes" type="temperature-sensor" uniq_id="107"/>
 
<item addr="300:98" cfgid="47" hw="out='BLGKH'" name="Temperature" system="yes" type="temperature-sensor" uniq_id="107"/>
 
</syntaxhighlight>
 
</syntaxhighlight>
 +
</translate>

Latest revision as of 11:56, 2 January 2022

Other languages:
English • ‎русский
Revision:
/B
/C


DW-LC07.C
DW-LC07C.png
Output ports
Number of switched channels7
Peak load16A
Other
Supply voltage11.5...27.5 V DC
Dimentions4U, 69x115x58 mm


7-CHANNEL ACTUATOR

This module is designed for high power AC/DC circuits commutation. Applicable for light, power sockets, for control of fan coil units, locks, blinds/gates.

Features

  • Control of a wide range of devices:
    • Lights
    • NC/NO heating valves
    • Blinds
    • 1 or 2-pole gates
    • 1 or 2-pole valves
    • NC/NO locks
    • Fan coil units
  • Relays with AgSnO2 contacts rated for 16A continuous load and 120A 20ms inrush current
  • Low noise relay switching
  • Built-in logical unit
  • Plug and play feature
  • Regular software updates

CAUTION! All work related to the installation, connection, setting up, service and support must be carried out by qualified personnel with sufficient skills and experience in working with electrical equipment. To avoid the risk of fire, electric shock, damage to the system and/or personal injury, the system installation and assembly must be performed in accordance with the instructions listed below:

  • all connectivity work must be carried out with the power turned OFF;
  • use appropriate tools and personal protection against electric shock;
  • do not use damaged cables, wires and connectors;
  • avoid folding the cables and wires;
  • do not apply excessive force to the wires by kinking or pressing them too hard: the inner conductors of the cables and wires may get stripped or damaged;
  • do not use the power socket with poor contacts to connect;
  • do not exceed the load limit parameters specified in the manual;
  • the supply conductors wire section is subject to the specifications for current density limit, insulation type and wire material. Light section can result in cable overheating and fire.

When the power is on, NEVER:

  • connect/disconnect the connectors;
  • open modules and sensors.

Overview

LC07C VIEW.png

Example of connection

LC07C EXA.png

Module dimensions

LC07C DIMM.png

Module parameters

Parameter name Value
Input channels qty
Input/output channels qty
0-10 input port quantity
Buttons
LED Buttons
Number of sensor inputs
Number of dry contact inputs
RS485 ports qty
RS232 ports qty
UART ports qty
M-BUS port quantity
Pulse inputs quantity
DALI ports qty
DALI-line voltage supply
Peak current of DALI-line power supply
Peak current in DALI-line
Maximum DALI devices quantity
Dimming channels qty
Output channels qty 7
0-10 output port quantity
Analog output channels qty
Output
Digital line maximum length
Discrete input channels qty
Digital input channels qty
Speakers
Max power output audio channel
Camera
IR lighting
Card reader
Connection type
Protocols
Backlight voltage
Load type
Dimmer load type
Supported sensors
Input voltage 0-250V
Current type AC/DC
Adjustment type
Max load
Min load
Max load per channel 16A
Max load per group
Max load per device
Control parameters
Angle of vision IR °
Angle of motion °
Temperature measuring range °C
Humidity measuring range
Dimmer type
Dimming type
Voltage that may be applied to the input channels 0-250V
Max output switching voltage
Max output switching current
Power supply 11.5 … 27.5 V DC from CAN
Max current(24V) 150 mA
Max current(13V)
Max detection distance
Max IR distance
Max BT distance
Max current
Relay
Data transfer speed
Permissible section of power supply cable to connect in socket:
single-conductor cable
multiple-conductor cable
tipped multiple-conductor cable

0.5 … 4mm2
0.5 … 4mm2
0.5 … 2.5mm2
Sensors VCC output
Sensors max VCC current
R1-R2 inputs max current
Push-button/reed switches line recommended length
Temperature sensor line max length
Sensor cable length
Sensors line max length
Bus type CAN (4-wire)
Compatible with
Output voltage
Output current
Equipment installation type DIN rail (EN 60715)
Mounting
Max cabel lenght
Case material ABS
Protection IP40
Temperature range -10 … +50 °C
Size 4U, 69x115x58 mm
Weight 180 g
* -
** -
*** -
1 -
2 -
3 -


Connectivity recommendations

In order to protect the actuator and loads connected to it, installing a circuit breaker is recommended. The nominal value of the circuit breaker should be calculated based on the maximum total load of connected devices and at the same time should not significantly exceed the maximum permissible characteristics of the actuator. Depending on the requirements, you can use one circuit breaker for one actuator (it is recommended) or one circuit breaker per each group of connected loads, or, if necessary, a separate circuit breaker can be installed for each load.

Connection of actuators

Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire. If free (unused) channels remain in a given group after a curtain/jalousie/shutter actuator with low-voltage control or gate actuator has been connected to it, these channels need to be left unused. (Do not connect other devices to them!)

Connection of the lights/electric contactor/heating thermal actuator

Lamps.png
Sample HW for this configuration

1hw="out='LLL----'"

Connection of high load device

Contactor Recomended contactors:
  • ABB ESB series
  • Schneider Acti 9 iCT series
  • Hager ESC series.

Connection of curtain/jalousie/shutter actuator with 220V force control

Pjalousie.png
Sample HW for this configuration

1hw="out='B------'"

Connection of curtain/jalousie/shutter actuator with low-voltage control

Ljalousie.png
Sample HW for this configuration

1hw="out='B------'"

Connection of single-pole gate actuator

1pgate.png
Sample HW for this configuration

1hw="out='X------'"

Connection of double-pole gate actuator

2pgate.png
Sample HW for this configuration

1hw="out='G------'"

Connection of single-pole water/gas supply valve

1pvalve.png
Sample HW for this configuration

1hw="out='R------'"

Connection of double-pole water/gas supply valve

2pvalve.png
Sample HW for this configuration

1hw="out='V------'"

Connection of fancoil control unit

Fancoil.png
Sample HW for this configuration

1hw="out='FFF----'"

Indication of module operation

Bootloader

Indicator Status Description
Top.png
Yl.png Device in bootloader
Bot.png
B.pngB.png Downloading firmware
R.pngR.png Flashing firmware

Firmware

Indicator Status Description
Top.png
G.pngG.pngG.pngDots.png Network configuration
B.pngB.pngB.pngDots.png Identification
Gl.png Operational mode
Yl.png Operational mode
Bot.png

Error
R.png Lost connection to server
R.pngR.png Overheat
R.pngR.pngR.png Overload
R.pngR.pngR.pngR.png No AC power
R.pngR.pngR.pngR.pngR.png RTC error
Bot.png

Activity
Y.png CAN activity
Bg.png OW activity
M.png RS-485 activity
B.png Ethernet activity


Module installation and connection procedure

  • Install the module in the switchboard on the DIN rail and fix it with the special latch on the module base.
  • Connect the CAN connector.
  • Connect the channels (1-7).
  • Configure the module using LT setup.
  • Apply power to the load.
  • Check all equipment for proper operation.

Module shut-off and deinstallation procedure

  • Disconnect the power from the load.
  • Disconnect the channels (1-7).
  • Disconnect the CAN connector.
  • Remove the module from the DIN rail, releasing the latch at the bottom of the module base.

HW settings

Name Type, range SUBID Default Description
runtime integer 0-100 1-7 15 runtime is the open/close time in seconds, is used for jalousie, gate, valve(2 pole); Example: runtime=15
runtimeopen integer 0-60000 Blinds subId Runtimeopen is the open time in milliseconds, is used for blinds; Example: runtimeopen=15000
runtimeclose integer 0-60000 Blinds subId Runtimeclose is the close time in milliseconds, is used for blinds; Example: runtimeclose=15000
hold integer 0-10000 1-7 500 hold is the bridging time in miliseconds, is used for gate and jalousie (by default hold is the same as runtime), lock; Example: hold=3500
def string 'ON' 1-7 'OFF' def is the element status is set after restart, is used for lamp, heating, valve(1 pole); Example: def='ON'
stop Char ‘R’ 1-6 (for 2-pole gate and blinds) If it is declared then by Stop command during the motion, the same impulse appears as it was at the beginning of the motion. Pole, an which the stop-impules is formed, is defined by the parameter Stop value. If it is ‘r’ or ‘R’ then stop-impulse is produced on the opposite to the start-impulse pole. If any other value is delcared (e.g., ‘d’ ) then the stop-impulse is on the same pole. If a Runtime passed after the beginning of the motion then the stop-impulse is not formed. Example: stop=’r’
out char[7] 98 'LLLLLLL' Each char is responsible for the type of a particular channel
  • 'L'-Lamp;
  • 'M'-Lamp Inverse;
  • 'J'-Heating NO, valve-heating, normally open;
  • 'H'-Heating NC, valve-heating, normally closed;
  • 'B'-Blinds (2 pole), jalousie/curtains;
  • 'C'-Blinds Inverse (2 pole), jalousie/curtains, invert open-close;
  • 'G'-Gate (2 pole), 2 pole gate;
  • 'D'-Gate (2 pole) Inverse, 2 pole gate, invert open-close;
  • 'X'-Gate (1 pole /short press), 1 pole gate;
  • 'Z'-Gate (1 pole) Inverse, 1 pole gate, invert open-close;
  • 'V'-Valve (2 pole), 2 pole valve;
  • 'W'-Valve (2 pole) Inverse, 2 pole valve, invert open-close;
  • 'R'-Valve (1 pole), 1 pole valve,;
  • 'S'-Valve (1 pole) Inverse, 1 pole valve, invert open-close;
  • 'K'-Lock (short press);
  • 'N'-Lock (short press) Inverse;
  • 'P'-Blinds (2 pole);
  • 'O'-Blinds Inverse (2 pole), invert open-close;
  • 'F'-FanCoil. Group1 (Lamp Toggle). For fancoil speed control;
  • 'E'-FanCoil. Group2 (Lamp Toggle). For fancoil speed control;
  • 'Q'-FanCoil. Group3 (Lamp Toggle). For fancoil speed control;
  • 'U'-FanCoil. Group4 (Lamp Toggle). For fancoil speed control;
  • 'I'-FanCoil. Group5 (Lamp Toggle). For fancoil speed control;
  • '-'-none, nothing is connected.

Example: out='BGLKM'

 1<item addr="300:1" cfgid="47" hw="runtime=60" name="Jalousie" sub-type="120" type="jalousie" uniq_id="117"/>
 2<item addr="300:3" auto-period="600" cfgid="47" hw="def='ON'" name="Lamp" type="lamp" uniq_id="110"/>
 3<item addr="300:4" cfgid="47" hw="runtime=30" name="Gate" sub-type="120" type="gate" uniq_id="118"/>
 4<item addr="300:6" auto-period="600" cfgid="47" hw="hold=5000" name="Lamp" type="lamp" uniq_id="113"/>
 5<item addr="300:7" cfgid="47" hw="def='ON'" name="Radiator" type="valve-heating" uniq_id="119">
 6    <automation name="Eco" temperature-level="16" uniq_id="120"/>
 7    <automation name="Comfort" temperature-level="22" uniq_id="121"/>
 8    <automation name="Hot" temperature-level="25" uniq_id="122"/>
 9</item>
10<item addr="300:97" cfgid="47" name="Temperature" system="yes" type="temperature-sensor" uniq_id="106"/>
11<item addr="300:98" cfgid="47" hw="out='BLGKH'" name="Temperature" system="yes" type="temperature-sensor" uniq_id="107"/>