editor, Interface administrators, Administrators, translation-admin, translator
9,706
edits
Changes
Jump to navigation
Jump to search
Line 4:
Line 4: − + Line 13:
Line 13: − + Line 19:
Line 19: + + + + + + + + + + + + Line 55:
Line 67: − − ==Overview== <!--T:6--> − [[File:HT07C VIEW.png|500px]] − − ==Example of connection== <!--T:7--> − [[File:HT07C EXA.png|500px]] − − ==Module dimensions== <!--T:8--> − [[File:HT07 DIMM.png|500px]] Line 77:
Line 80: − + Line 84:
Line 87: − + Line 97:
Line 100: − + + + + + − + − + − + Line 113:
Line 120: − + − + Line 192:
Line 199: − + Line 242:
Line 249: − + Line 259:
Line 266: + + Line 270:
Line 279: − +
no edit summary
{{Infobox module
{{Infobox module
| name = DW-RC12.B
| name = DW-RC12.B
| image = DW-HT07C.png
| image = DW-RC12.B.png
| outCount = 12
| outCount = 12
| dimmOut =
| dimmOut =
| inDigit = 4
| inDigit = 4
| voltage = 11.5...27.5 V DC
| voltage = 11.5...27.5 V DC
| dim = 4U, 69x115x58 mm
| dim = 9U, 156x110x58 mm
}}
}}
Has 12 outputs for connecting loads and 24 inputs for connecting
Has 12 outputs for connecting loads and 24 inputs for connecting
various sensors/buttons.
various sensors/buttons.
<!--T:23-->
Module general view is shown in '''fig. 1'''
<!--T:24-->
[[File:DW-RC12.B dwg.png|700px|Fig. 1 Module general view]]
<br>
==Features== <!--T:3-->
==Features== <!--T:3-->
*open modules and sensors.
*open modules and sensors.
</div>
</div>
==Module parameters== <!--T:9-->
==Module parameters== <!--T:9-->
| maxperch = 16A
| maxperch = 16A
| power = 20.0 … 27.5 V DC from CAN
| power = 20.0 … 27.5 V DC from CAN
| maxcur24v = 140 mA
| maxcur24v = 260 mA
| bustype = CAN
| bustype = CAN
| instalation = DIN rail (EN 60715)
| instalation = DIN rail (EN 60715)
| temprange = -10 … +50 °C
| temprange = -10 … +50 °C
| size = 9U, 156x110x58 mm
| size = 9U, 156x110x58 mm
| weight = ??? g
| weight = 400 g
}}
}}
for each load.
for each load.
==Connection of actuators== <!--T:13-->
<!--T:13-->
Typical diagram of DW-RC12.B module connection is shown in '''fig. 2.'''
<div style="clear: both">[[File:DW-RC12.B scheme.png|700px|Fig. 2]]</div>
==Connection of actuators== <!--T:14-->
<!--T:14-->
<!--T:15-->
<div class="caution"> Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
<div class="caution"> Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
If free (unused) channels remain in a given group after a curtain/jalousie/shutter actuator with low-voltage control or gate actuator has been connected to it, these channels need to be left unused. (Do not connect other devices to them!) </div>
If free (unused) channels remain in a given group after a curtain/jalousie/shutter actuator with low-voltage control or gate actuator has been connected to it, these channels need to be left unused. (Do not connect other devices to them!) </div>
===Connection of the lights/electric contactor/heating thermal actuator=== <!--T:15-->
===Connection of the lights/electric contactor/heating thermal actuator=== <!--T:16-->
<!--T:16-->
<!--T:17-->
[[File:lamps.png|200px]]<br>
[[File:lamps.png|200px]]<br>
Sample HW for this configuration
Sample HW for this configuration
===Connection of high load device=== <!--T:17-->
===Connection of high load device=== <!--T:18-->
<!--T:18-->
<!--T:19-->
{| class="wikitable" style="width:800px";
{| class="wikitable" style="width:800px";
|-
|-
<!--T:34-->
<!--T:34-->
[[File:SensorsCon4.png|200px]]<br>
[[File:SensorsRC12.png|200px]]<br>
2-wire connection recommended
2-wire connection recommended
|stop||Char ‘R’||1-12||–||(for 2-pole gate and blinds) If it is declared then by Stop command during the motion, the same impulse appears as it was at the beginning of the motion. Pole, an which the stop-impules is formed, is defined by the parameter Stop value. If it is ‘r’ or ‘R’ then stop-impulse is produced on the opposite to the start-impulse pole. If any other value is delcared (e.g., ‘d’ ) then the stop-impulse is on the same pole. If a Runtime passed after the beginning of the motion then the stop-impulse is not formed. Example: stop=’r’
|stop||Char ‘R’||1-12||–||(for 2-pole gate and blinds) If it is declared then by Stop command during the motion, the same impulse appears as it was at the beginning of the motion. Pole, an which the stop-impules is formed, is defined by the parameter Stop value. If it is ‘r’ or ‘R’ then stop-impulse is produced on the opposite to the start-impulse pole. If any other value is delcared (e.g., ‘d’ ) then the stop-impulse is on the same pole. If a Runtime passed after the beginning of the motion then the stop-impulse is not formed. Example: stop=’r’
|-
|-
|out||char[7]||98||'LLLLLLL'||Each char is responsible for the type of a particular channel
|out||char[12]||98||'LLLLLLLLLLLL'||Each char is responsible for the type of a particular channel
*'L'-Lamp;
*'L'-Lamp;
*'M'-Lamp Inverse;
*'M'-Lamp Inverse;
*'K'-Lock (short press);
*'K'-Lock (short press);
*'N'-Lock (short press) Inverse;
*'N'-Lock (short press) Inverse;
*'P'-Blinds (2 pole);
*'O'-Blinds Inverse (2 pole), invert open-close;
*'F'-FanCoil. Group1 (Lamp Toggle). For fancoil speed control;
*'F'-FanCoil. Group1 (Lamp Toggle). For fancoil speed control;
*'E'-FanCoil. Group2 (Lamp Toggle). For fancoil speed control;
*'E'-FanCoil. Group2 (Lamp Toggle). For fancoil speed control;
For example, offset is -3.8 : hw="offset='-3.8'"
For example, offset is -3.8 : hw="offset='-3.8'"
|-
|-
|in||char[12]||98||'KKKKKKKKKKKK'||Each char is responsible for the type of a particular channel
|in||char[24]||98||'KKKKKKKKKKKKKKKKKKKKKKKK'||Each char is responsible for the type of a particular channel
*'B'-Button;
*'B'-Button;
*'C'-Inverted button;
*'C'-Inverted button;