editor, Interface administrators, Administrators, translation-admin, translator
9,706
edits
Changes
Jump to navigation
Jump to search
Line 25:
Line 25: − + − ===System installation and assembly=== <!--T:31-->+ − Before connecting the system, you must: − − <!--T:32--> − *site the sensor and actuators (if not pre-installed), set the sensors and actuators; − *site the module and power supply. − − − <!--T:33--> − '''Note: The module must be installed near the power supply voltage source.''' − <!--T:34--> − <div class="cautoin"> − − <!--T:35--> − Typical diagram of DW-RC12.B module connection is shown in '''fig. 2.''' − <div style="clear: both">[[File:DW-RC12.B scheme.png|700px|Fig. 2]]</div> Line 95:
Line 80: − + Line 102:
Line 87: − + Line 115:
Line 100: − + + + + + − + − + − + Line 131:
Line 120: − + − + Line 210:
Line 199: − +
no edit summary
<!--T:24-->
<!--T:24-->
[[File:DW-RC12.B dwg.png|700px|frameless|left|Fig. 1 Module general view]]
[[File:DW-RC12.B dwg.png|700px|Fig. 1 Module general view]]
<br>
==Features== <!--T:3-->
==Features== <!--T:3-->
| maxperch = 16A
| maxperch = 16A
| power = 20.0 … 27.5 V DC from CAN
| power = 20.0 … 27.5 V DC from CAN
| maxcur24v = ??? mA
| maxcur24v = 260 mA
| bustype = CAN
| bustype = CAN
| instalation = DIN rail (EN 60715)
| instalation = DIN rail (EN 60715)
| temprange = -10 … +50 °C
| temprange = -10 … +50 °C
| size = 9U, 156x110x58 mm
| size = 9U, 156x110x58 mm
| weight = ??? g
| weight = 400 g
}}
}}
for each load.
for each load.
==Connection of actuators== <!--T:13-->
<!--T:13-->
Typical diagram of DW-RC12.B module connection is shown in '''fig. 2.'''
<div style="clear: both">[[File:DW-RC12.B scheme.png|700px|Fig. 2]]</div>
==Connection of actuators== <!--T:14-->
<!--T:14-->
<!--T:15-->
<div class="caution"> Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
<div class="caution"> Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
If free (unused) channels remain in a given group after a curtain/jalousie/shutter actuator with low-voltage control or gate actuator has been connected to it, these channels need to be left unused. (Do not connect other devices to them!) </div>
If free (unused) channels remain in a given group after a curtain/jalousie/shutter actuator with low-voltage control or gate actuator has been connected to it, these channels need to be left unused. (Do not connect other devices to them!) </div>
===Connection of the lights/electric contactor/heating thermal actuator=== <!--T:15-->
===Connection of the lights/electric contactor/heating thermal actuator=== <!--T:16-->
<!--T:16-->
<!--T:17-->
[[File:lamps.png|200px]]<br>
[[File:lamps.png|200px]]<br>
Sample HW for this configuration
Sample HW for this configuration
===Connection of high load device=== <!--T:17-->
===Connection of high load device=== <!--T:18-->
<!--T:18-->
<!--T:19-->
{| class="wikitable" style="width:800px";
{| class="wikitable" style="width:800px";
|-
|-
<!--T:34-->
<!--T:34-->
[[File:SensorsCon4.png|200px]]<br>
[[File:SensorsRC12.png|200px]]<br>
2-wire connection recommended
2-wire connection recommended