DW-WL02

Revision as of 14:11, 6 January 2022 by Rusanov (talk | contribs) (Created page with "==Индикация работы модуля== ===Загрузчик=== {{indication| textBBB= Ожидание команды загрузчика}} ===Прошивка===...")
Other languages:
English • ‎русский
Revision:
/B
/C


DW-WL02.C
DW-WL02C.png
Output ports
Number of switched channels4
Peak load5A
Input ports
Number of sensor inputs4
Number of dry contact inputs2
Other
Supply voltage11.5...27.5 V DC
Dimentions4U, 69x110x58 mm


МОДУЛЬ ЗАЩИТЫ ОТ ПРОТЕЧКИ

Модуль поддерживает подключение 2-х клапанов перекрытия подачи воды и 4-х датчиков протечки (до 16-ти датчиков FW-WL.B/EW-WL.B).

Функции

  • Поддержка 1/2-х полюсных клапанов
  • Геркон обратной связи клапана
  • Поддерживает до 16-ти датчиков протечки
  • Обнаружение и диагностика датчиков
  • Настройка чувствительности датчиков

ВНИМАНИЕ! Все работы, связанные с установкой, подключением, настройкой, обслуживанием и поддержкой оборудования, должны выполняться только квалифицированным персоналом, обладающим достаточными навыками и опытом работы с электрооборудованием! Во избежание риска возгорания, поражения электрическим током, повреждения системы и/или травм, установка и сборка системы должны выполняться в соответствии с указаниями, перечисленными ниже:

  • все работы по подключению должны выполняться при выключенном питании;
  • необходимо использовать соответствующие инструменты и средства индивидуальной защиты от поражения электрическим током;
  • запрещается использовать поврежденные кабели, провода и разъемы;
  • избегайте перегиба проводов и кабелей;
  • не прилагайте чрезмерных усилий к проводам путем их перегиба или слишком сильного сжатия: внутренние проводники кабелей и проводов могут быть оголены или повреждены;
  • не используйте для подключения разъемы с плохими контактами;
  • не превышайте параметры предельной нагрузки, указанные в инструкции;
  • сечение питающих проводов зависит от требований к пределу плотности тока, типу изоляции и материалу проводов. Недостаточное сечение провода может привести к перегреву кабеля и возгоранию.

Когда питание включено, НИКОГДА:

  • не подключайте/отключайте разъемы;
  • не открывайте модули и датчики.

Изображение модуля

 

 

Пример подключения

 

Размеры модуля

 

Внутренняя компоновка

 


Параметры модуля

Parameter name Value
Input channels qty
Input/output channels qty
0-10 input port quantity
Buttons
LED Buttons
Number of sensor inputs 4 FW-WL.A/EW-WL.A
16 FW-WL.B/EW-WL.B (4 per input)
Number of dry contact inputs 2
RS485 ports qty
RS232 ports qty
UART ports qty
M-BUS port quantity
Pulse inputs quantity
DALI ports qty
DALI-line voltage supply
Peak current of DALI-line power supply
Peak current in DALI-line
Maximum DALI devices quantity
Dimming channels qty
Output channels qty 4
0-10 output port quantity
Analog output channels qty
Output
Digital line maximum length
Discrete input channels qty
Digital input channels qty
Speakers
Max power output audio channel
Camera
IR lighting
Card reader
Connection type
Protocols
Backlight voltage
Load type
Dimmer load type
Supported sensors
Input voltage 0-250 V AC/DC
Current type AC/DC
Adjustment type
Max load
Min load
Max load per channel 5A
Max load per group
Max load per device
Control parameters
Angle of vision IR °
Angle of motion °
Temperature measuring range °C
Humidity measuring range
Dimmer type
Dimming type
Voltage that may be applied to the input channels 0-250 V AC/DC
Max output switching voltage
Max output switching current
Power supply 11.5 … 27.5 V DC from CAN
Max current(24V) 60 mA
Max current(13V)
Max detection distance
Max IR distance
Max BT distance
Max current
Relay
Data transfer speed
Permissible section of power supply cable to connect in socket:
Sensors VCC output 8..12 V
Sensors max VCC current 70 mA
R1-R2 inputs max current 3 mA
Push-button/reed switches line recommended length
Temperature sensor line max length
Sensor cable length
Sensors line max length 30m
Bus type CAN (4-wire)
Compatible with
Output voltage
Output current
Equipment installation type DIN rail (EN 60715)
Mounting
Max cabel lenght
Case material ABS
Protection IP40
Temperature range -10 … +50 °C
Size 4U, 69x110x58 mm
Weight 100 g
* -
** -
*** -
1 -
2 -
3 -


Индикация работы модуля

Загрузчик

Indicator Status Description
 
  Device in bootloader
 
   Downloading firmware
   Flashing firmware

Прошивка

Indicator Status Description
 
     Network configuration
     Identification
  Operational mode
  Operational mode
 

Error
  Lost connection to server
   Overheat
    Overload
     No AC power
      RTC error
 

Activity
  CAN activity
  OW activity
  RS-485 activity
  Ethernet activity


Module installation and connection procedure

  1. Install the module in the switchboard on the DIN rail and fix it with the special latch on the module base.
  2. Connect the CAN connector.
  3. Connect the channels.
  4. Configure the module using LT setup.
  5. Apply power to the load.
  6. Check all equipment for proper operation.

Module shut-off and deinstallation procedure

  1. Disconnect the power from the load.
  2. Disconnect the channels.
  3. Disconnect the CAN connector.
  4. Remove the module from the DIN rail, releasing the latch at the bottom of the module base.

HW settings

Name Type, range SUBID Default Description
runtime integer 0-100 1-4 15 runtime is the open/close time in seconds, is used for jalousie, gate, valve(2 pole); Example: runtime=15
runtimeopen integer 0-60000 Blinds subId - Runtimeopen is the open time in milliseconds, is used for blinds; Example: runtimeopen=15000
runtimeclose integer 0-60000 Blinds subId - Runtimeclose is the close time in milliseconds, is used for blinds; Example: runtimeclose=15000
hold integer 0-10000 1-4 500 hold is the bridging time in miliseconds, is used for gate and jalousie (by default hold is the same as runtime), lock; Example: hold=3500
def string 'ON' 1-4 'OFF' Def is the element status is set after restart, is used for lamp, heating, valve(1 pole); Example: def='ON'
out char[4] 98 'V-V-' Each char is responsible for the type of a particular channel
  • 'L'-Lamp;
  • 'M'-Lamp Inverse;
  • 'J'-Heating NO, valve-heating, normally open;
  • 'H'-Heating NC, valve-heating, normally closed;
  • 'B'-Blinds (2 pole), jalousie/curtains;
  • 'C'-Blinds Inverse (2 pole), jalousie/curtains, invert open-close;
  • 'G'-Gate (2 pole), 2 pole gate;
  • 'D'-Gate (2 pole) Inverse, 2 pole gate, invert open-close;
  • 'X'-Gate (1 pole /short press), 1 pole gate;
  • 'Z'-Gate (1 pole) Inverse, 1 pole gate, invert open-close;
  • 'V'-Valve (2 pole), 2 pole valve;
  • 'W'-Valve (2 pole) Inverse, 2 pole valve, invert open-close;
  • 'R'-Valve (1 pole), 1 pole valve,;
  • 'S'-Valve (1 pole) Inverse, 1 pole valve, invert open-close;
  • 'K'-Lock (short press);
  • 'N'-Lock (short press) Inverse;
  • 'P'-Blinds (2 pole);
  • 'O'-Blinds Inverse (2 pole), invert open-close;
  • '-'-none, nothing is connected.

Example: out='V-V-'

leak char[4] 98 'LLLL' Each char is responsible for the type of a particular channel
  • 'L'-Leak, Built-in floor (EW-WL) or on-the-floor (FW-WL) leakage sensor
  • 'N'-Third party leakage sensor;
  • 'S' – Leak, on-the-floor (FW-WL.B) leakage sensor
  • '-'-none
in char[2] 98 'KK' Each char is responsible for the type of a particular channel
  • 'K' – Contact;
  • 'H' – Inverted contact;
  • '-' – none;

Example: in='HHKK'

 1<item addr="500:1" cfgid="53" hw="runtime=30" name="Valve" type="valve" uniq_id="4105"/>
 2<item addr="500:3" cfgid="53" name="Jalousie" sub-type="120" type="jalousie" uniq_id="4117"/>
 3<item addr="500:11" cfgid="53" name="Leak" type="leak-sensor" uniq_id="4107"/>
 4<item addr="500:12" cfgid="53" name="Leak" type="leak-sensor" uniq_id="4108"/>
 5<item addr="500:13" cfgid="53" name="Leak" type="leak-sensor" uniq_id="4109"/>
 6<item addr="500:14" cfgid="53" name="Leak" type="leak-sensor" uniq_id="4110"/>
 7<item addr="500:21" cfgid="53" name="Door" type="door-sensor" uniq_id="4111"/>
 8<item addr="500:22" cfgid="53" name="Door" type="door-sensor" uniq_id="4112"/>
 9<item addr="500:23" cfgid="53" name="Door" type="door-sensor" uniq_id="4113"/>
10<item addr="500:24" cfgid="53" name="Door" type="door-sensor" uniq_id="4114"/>
11<item addr="500:97" cfgid="53" name="Temperature" system="yes" type="temperature-sensor" uniq_id="4115"/>
12<item addr="500:98" cfgid="53" hw="leak='NNLL' in='HHKK' out='V-B-'" name="Temperature" system="yes" type="temperature-sensor" uniq_id="4116"/>