EIB

Revision as of 11:59, 17 January 2022 by Rusanov (talk | contribs) (Created page with "От EIB (BAOS, chID 0, seq_cntr 0) => источник 1/1/3 адресат 5/0/2 длина данных 1: 09 - '''Запуск диммирования в сторону...")
Other languages:
English • ‎русский

Нажатие и отпускание выключателя (рекомендуется)

Для корректной работы требуется, чтобы кнопка при нажатии отправляла 1, а при отпускании 0. Этот тип настройки можно использовать для двойного, тройного щелчка и диммирования.

Настройка кнопок в ЭТС:


 

 

Настройки плагина EIB:


 

ФАЙЛ ОТЧЕТА:

От EIB (BAOS, chID 0, seq_cntr 0) => источник 1/1/1 адресат 2/0/0 длина данных 1: 01  - Кнопка нажата
От EIB (BAOS, chID 0, seq_cntr 0) => источник 1/1/1 адресат 2/0/0 длина данных 1: 00  - Кнопка отпущена
От EIB (BAOS, chID 0, seq_cntr 0) => источник 15/15/255 адресат 2/0/2 длина данных 1: 01  - Отзыв отправлен

Выключатель с одной кнопкой

Каждое нажатие кнопки отправляет 1 байт данных (попеременно 0 или 1). Для запуска/остановки диммирования кнопка отправляет 9/8 или 1/0 на адрес группы диммирования.

Настройки кнопки в ЭТС:


 
Или:
 

 

Настройки в плагине EIB:


 

ФАЙЛ ОТЧЕТА:

От EIB (BAOS, chID 0, seq_cntr 0) => источник 1/1/3 адресат 5/0/0 длина данных 1: 01 - Кнопка нажата
From EIB (BAOS, chID 0, seq_cntr 0) => источник 15/15/255 адресат 5/0/1 длина данных 1: 01 - Отзыв отправлен
От EIB (BAOS, chID 0, seq_cntr 0) => источник 1/1/3 адресат 5/0/0 длина данных 1: 00 - Кнопка нажата

From EIB (BAOS, chID 0, seq_cntr 0) => источник 15/15/255 адресат 5/0/1 длина данных 1: 00 - Отзыв отправлен

От EIB (BAOS, chID 0, seq_cntr 0) => источник 1/1/3 адресат 5/0/2 длина данных 1: 09 - Запуск диммирования в сторону увеличения
From EIB (BAOS, chID 0, seq_cntr 0) => источник 15/15/255 адресат 5/0/2 длина данных 1: 08 - Остановка диммирования в сторону увеличения
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/2 data len 1: 01 - Dimming DOWN started
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/3 destination 5/0/2 data len 1: 00 - Dimming DOWN finished

Switch-two-phys-btn

This type of configuration is used if you have physically 2 buttons on a panel, one of which always sends the command on (1) and the second off (0). In this case, 2 buttons are created in the Larnitech system, each of which can be used independently. Most of the panels do not allow independent use of the feedback LEDs, therefore, if the keys are used independently, the indication may not work correctly.

Button configuration in ETS:


 

 

Configuration in EIB plugin:


 

LOG:

From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/2 data len 1: 01 - Button 1 pressed
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/3 data len 1: 01  - Feedback 2 sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/0 data len 1: 01  - Feedback sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/2 data len 1: 00 - Button 2 pressed
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/3 data len 1: 00  - Feedback 2 sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/0 data len 1: 00  - Feedback sent

Switch-long-press

Works the same as Switch-two-phys-btn, the difference is that dimming is added.

Button configuration in ETS:


 

 

 

Configuration in EIB plugin:


 

LOG:

From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/2 data len 1: 01  - Button 1 pressed
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/3 data len 1: 01 - Feedback 2 sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/0 data len 1: 01 - Feedback sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/2 data len 1: 00  - Button 2 pressed
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/3 data len 1: 00 - Feedback 2 sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 2/0/0 data len 1: 00 - Feedback sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/1 data len 1: 01 - Button 1 dimming started
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/1 data len 1: 00 - Button 1 dimming finished
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/1 data len 1: 09 - Button 2 dimming started
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 2/0/1 data len 1: 08 - Button 2 dimming finished

Temperature Sensor

Creates a temperature sensor in the Larnitech system.

Sensor configuration in ETS:


 

 

Configuration in EIB plugin:


 

LOG:

From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/1/5 data len 3: 00 0c c4  - Received temperature from the sensor

Thermostat

The plugin ensures temperature setpoint synchronization between a thermostat and valve-heating element in the Larnitech system

Thermostat configuration in ETS:


 

 

 

Configuration in EIB plugin:


 

LOG:

From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 4/0/2 data len 3: 00 0c 4c - Setpoint sent to the thermostat
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0c 4c - Setpoint received from the thermostat

Climate Control

Heat/Cool Setpoint - Must be selected if the thermostat panel has only 1 address for two setpoints. In this case, depending on the selected mode in the climate control, the following values will be taken:

  • If climate control is in heating mode, Heat/Cool setpoint will be accepted as the heating setpoint. Likewise within the Cooling mode, Heat/Cool setpoint will be accepted as the cooling setpoint.
  • If the climate control is in the Heating/Cooling mode, it will use add/subtract delta and set 2 setpoints (Heat and cool). For example setpoint 25 will be transformed to 23-27.

Thermostat configuration in ETS:


 

 

 

 

 

 

Configuration in EIB plugin:


 

 

 


LOG:

From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/3/1 data len 1: 00 - Turn OFF
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0d 46 - Setpoint received
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/3/1 data len 1: 01 - Turn ON
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0d 46 - Setpoint received
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 4/0/2 data len 3: 00 0c e2 - Setpoint sent to the thermostat
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0c e2 - Setpoint received

Air Conditioner

In case the device does can't send mode with the DPT 20.105 data type, but simply sends [1,2,3,4,0…], you can set your own correspondence of values to the mode

Configuration in ETS:


 

 

 

 

 

 

 

 


Configuration in EIB plugin:


 

 

LOG:

From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/3/1 data len 1: 00 - Turn OFF
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0d 46 - Setpoint received
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/3/1 data len 1: 01 - Turn ON
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0d 46 - Setpoint received
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/2/0 data len 2: 00 04 - Mode changed to Heating
From EIB (BAOS, chID 0, seq_cntr 0) => source 15/15/255 destination 4/0/2 data len 3: 00 0c e2 - Setpoint sent
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/0/1 data len 3: 00 0c e2 - Setpoint received
From EIB (BAOS, chID 0, seq_cntr 0) => source 1/1/1 destination 4/4/0 data len 2: 00 03 - Sending FAN speed