editor, Interface administrators, Administrators, translation-admin, translator
9,706
edits
Changes
no edit summary
{| class="wikitable" style="clear:left;"
{| class="wikitable" style="clear:left;"
|-
|-
|1 || — connector for load application
|1 || — konektor za primenu opterećenja
|-
|-
|2 || — connector for dimming-lamps application
|2 || — konektor za primenu lampi za zatamnjivanje
|-
|-
|3 || — power connector
|3 || - konektor za napajanje
|-
|-
|4 || — Ethernet network connector
|4 || — Ethernet mrežni konektor
|-
|-
|5-6 || — connectors for digital sensors and buttons/switching units
|5-6 || — konektori za digitalne senzore i dugmad/sklopke
|-
|-
|7 || — OneWire interface connector (for digital sensors)
|7 || — OneVire konektor za interfejs (za digitalne senzore)
|-
|-
|8 || — connector for expansion module.
|8 || — konektor za modul za proširenje.
|}
|}
'''Overview of the METAFORSA device external connectors:'''
'''Pregled eksternih konektora uređaja METAFORSA:'''
Na vrhu kućišta (''sl. 1'') nalazi se:
*connector (1) — Devices connection;
*konektor (1) — Veza uređaja;
*connector (2) — Dimming lamps connection;
*konektor (2) — priključak sijalica za prigušivanje;
|+ text-align="left"|'''Table2'''
|+ text-align="left"|'''Table2'''
|-
|-
!Konektor!!Kontakt!!Zadatak|-
!Konektor!!Kontakt!!Zadatak
|-
|[[File:Out.png|80px|frameless]] ||1-10|| Primena opterećenja (svetleće lampe, termički aktuatori, itd.)
|[[File:Out.png|80px|frameless]] ||1-10|| Primena opterećenja (svetleće lampe, termički aktuatori, itd.)
|-
|-
*proverite priključak jedinice za napajanje na 220V strujnu mrežu, indikator treba da bude UKLJUČENO.
*proverite priključak jedinice za napajanje na 220V strujnu mrežu, indikator treba da bude UKLJUČENO.
===Network connection fault:===
===Kreška mrežne veze:===
*ensure the Ethernet cable is properly wired and connected to the connector;
*uverite se da je Ethernet kabl pravilno ožičen i povezan sa konektorom;
*ensure the LED status indicators are ON on the Ethernet connector;
*uverite se da su LED indikatori statusa UKLJUČENI na Ethernet konektoru;
*check the LAN configuration is correct, Ethernet cable loops are absent;
*proverite da li je LAN konfiguracija ispravna, petlje Ethernet kabla odsutne;
*METAFORSA module and the device you are connecting from are in the same network.
*METAFORSA modul i uređaj sa kojeg se povezujete su u istoj mreži.
hold integer 0-10000 1-10 by default hold is the same as runtime
hold integer 0-10000 1-10 podrazumevano zadržavanje je isto što i vreme izvršavanja
hold is the bridging time in miliseconds, is used for gate and jalousie, lock; Example: hold=3500
hold je vreme premošćavanja u milisekundama, koristi se za kapiju i žaluziju, zaključavanje; Primer: hold=3500
===The sensors do not operate:===
===Senzori ne rade:===
*ensure the inputs are properly configured in the application ('''System Setup Instructions''');
*uverite se da su ulazi pravilno konfigurisani u aplikaciji ('''Uputstva za podešavanje sistema''');
*check the connection is correct in accordance with '''table 2''' and paragraph 3.7;
*proverite da li je veza ispravna u skladu sa '''tabelom 2''' i paragrafom 3.7;
*ensure the METAFORSA module is ON: circuit breaker assembly is closed, indication on the supply unit is ON, the module indication corresponds to the operating status – '''table 3''';
*uverite se da je METAFORSA modul UKLJUČEN: sklop prekidača je zatvoren, indikacija na jedinici napajanja je UKLJUČENA, indikacija modula odgovara radnom statusu – '''tabela 3''';
*check the power supply availability on the sensors;
*proverite dostupnost napajanja na senzorima;
*check the integrity of lines laid to the sensors.
*proverite integritet vodova postavljenih do senzora.
===The auxiliary equipment does not operate:===
===Pomoćna oprema ne radi:===
*check the connection is correct in accordance with table 2 and paragraph 3.8-9;
*proveriti da li je veza ispravna u skladu sa tabelom 2 i stavom 3.8-9;
*ensure the METAFORSA module is ON: circuit breaker assembly is closed, indication on the supply unit is ON, the module indication corresponds to the operating status – table 3;
*uverite se da je METAFORSA modul UKLJUČEN: sklop prekidača je zatvoren, indikacija na jedinici napajanja je UKLJUČENA, indikacija modula odgovara radnom statusu – tabela 3;
*check the integrity of the CAN lines, voltage supply on the modules.
*proverite integritet CAN vodova, napajanje napona na modulima.
==HW Settings==
==HW Podešavanja==
{| class="wikitable"
{| class="wikitable"
|-
|-
!Name!!Type, range!!SUBID!!Default!!Description
!Ime!!Tip, opseg!!SUBID!!Podrazumevano!!Opis
|-
|-
|runtime||integer 0-100 || 1-10 || 15 ||runtime is the open/close time in seconds, is used for jalousie, gate, valve(2 pole);
|runtime||integer 0-100 || 1-10 || 15 ||vreme rada je vreme otvaranja/zatvaranja u sekundama, koristi se za žaluziju, kapiju, ventil (2 pola);
<br>Example: runtime=15
<br>Primer: runtime=15
|-
|-
|runtimeopen||integer 0-60000||Blinds subId || ||Runtimeopen is the open time in milliseconds, is used for blinds; Example: runtimeopen=15000
|runtimeopen||integer 0-60000||Blinds subId || ||Runtimeopen je otvoreno vreme u milisekundama, koristi se za roletne; Primer: runtimeopen=15000
|-
|-
|runtimeclose||integer 0-60000||Blinds subId|| ||Runtimeclose is the close time in milliseconds, is used for blinds; Example: runtimeclose=15000
|runtimeclose||integer 0-60000||Blinds subId|| ||Runtimeclose je vreme zatvaranja u milisekundama, koristi se za roletne; Primer: runtimeclose=15000
|-
|-
|hold||integer 0-10000||1-10||500||hold is the bridging time in milliseconds, is used for gate and jalousie (by default hold is the same as runtime for jalousie and gate), lock; Example: hold=3500
|hold||integer 0-10000||1-10||500||hold je vreme premošćavanja u milisekundama, koristi se za kapiju i žaluziju (podrazumevano zadržavanje je isto kao vreme izvođenja za žaluziju i kapiju), zaključavanje; Primer: hold=3500
|-
|-
|def||string 'ON'||1-10||'OFF'||def is the element status is set after restart, is used for lamp, heating, valve(1 pole); Example: def='ON'
|def||string 'ON'||1-10||'OFF'||def je status elementa koji se postavlja nakon ponovnog pokretanja, koristi se za lampu, grejanje, ventil (1 pol); Primer: def='ON'
|-
|-
|stop||Char ‘R’||1-7||–||(for 2-pole gate and blinds) If it is declared then by Stop command during the motion, the same impulse appears as it was at the beginning of the motion. Pole, an which the stop-impules is formed, is defined by the parameter Stop value. If it is ‘r’ or ‘R’ then stop-impulse is produced on the opposite to the start-impulse pole. If any other value is delcared (e.g., ‘d’ ) then the stop-impulse is on the same pole. If a Runtime passed after the beginning of the motion then the stop-impulse is not formed. Example: stop=’r’
|stop||Char ‘R’||1-7||–||(za 2-polne kapije i roletne) Ako se deklariše tada komandom Stop tokom kretanja, pojavljuje se isti impuls kao i na početku kretanja. Pol, na kome se formiraju stop-impuli, definisan je parametrom Stop vrednost. Ako je 'r' ili 'R' onda se stop-impuls proizvodi na suprotnom od pola start-impulsa. Ako je bilo koja druga vrednost označena (npr. 'd'), onda je stop-impuls na istom polu. Ako je Runtime prošlo nakon početka kretanja, onda se stop-impuls ne formira. Primer: stop=’r’
|-
|-
|out||char[10]||98||'LLLLHHHHP-'||Each char is responsible for the type of a particular channel
|out||char[10]||98||'LLLLHHHHP-'||Svaki znak je odgovoran za tip određenog kanala
*'L'-Lamp;
*'L'-Lamp;
*'M'-Lamp Inverse;
*'M'-Lamp Inverse;
*'J'-Heating NO, valve-heating, normally open;
*'J'-grejanje NE, ventil za grejanje, normalno otvoren;
*'H'-Heating NC, valve-heating, normally closed;
*'H'-grejanje NC, ventil za grejanje, normalno zatvoren;
*'B'-Blinds (2 pole), jalousie/curtains;
*'B'-Roletne (2 pol), žaluzine/zavese;
*'C'-Blinds Inverse (2 pole), jalousie/curtains, invert open-close;
*'C'-Roletne Inverse (2 pol), žaluzije/zavese, invertno otvaranje-zatvaranje;
*'G'-Gate (2 pole), 2 pole gate;
*'G'-kapija (2-polna), 2-polna kapija;
*'D'-Gate (2 pole) Inverse, 2 pole gate, invert open-close;
*'D'-kapija (2-polna) Inverzna, 2-polna kapija, invertno otvaranje-zatvaranje;
*'X'-Gate (1 pole /short press), 1 pole gate;
*'Ks'-Gate (1 pole /kratki pritisak), 1 pole kapija;
*'Z'-Gate (1 pole) Inverse, 1 pole gate, invert open-close;
*'Z'-kapija (1 pol) Inverzna, 1-polna kapija, invertno otvaranje-zatvaranje;
*'V'-Valve (2 pole), 2 pole valve;
*'V'-ventil (2-polni), 2-polni ventil;
*'W'-Valve (2 pole) Inverse, 2 pole valve, invert open-close;
*'V'-ventil (2-polni) Inverzni, 2-polni ventil, invertno otvaranje-zatvaranje;
*'R'-Valve (1 pole), 1 pole valve,;
*'R'-ventil (1-polni), 1-polni ventil,;
*'S'-Valve (1 pole) Inverse, 1 pole valve, invert open-close;
*'S'-ventil (1 polni) Inverzni, 1-polni ventil, invertni otvaranje-zatvaranje;
*'K'-Lock (short press);
*'K'-Lock (kratak pritisak);
*'N'-Lock (short press) Inverse;
*'N'-Lock (kratak pritisak) Inverzno;
*'P'-Blinds (2 pole);
*'P'-roletne (2 polne);
*'O'-Blinds Inverse (2 pole), invert open-close;
*'O'-Blinds Inverse (2 pol), obrnuti otvaranje-zatvaranje;
*'F'-FanCoil. Group1 (Lamp Toggle). For fancoil speed control;
*'F'-FanCoil. Group1 (Lamp Toggle). Za kontrolu brzine ventilatora;
*'E'-FanCoil. Group2 (Lamp Toggle). For fancoil speed control;
*'E'-FanCoil. Group2 (Lamp Toggle). Za kontrolu brzine ventilatora;
*'Q'-FanCoil. Group3 (Lamp Toggle). For fancoil speed control;
*'K'-FanCoil. Group3 (Lamp Toggle). Za kontrolu brzine ventilatora;
*'U'-FanCoil. Group4 (Lamp Toggle). For fancoil speed control;
*'U'-FanCoil. Group4 (Lamp Toggle). Za kontrolu brzine ventilatora;
*'I'-FanCoil. Group5 (Lamp Toggle). For fancoil speed control;
*'I'-FanCoil. Grupa 5 (Prebacivanje lampe). Za kontrolu brzine ventilatora;
*'-'-none, nothing is connected.
*'-'-nema, ništa nije povezano.
Primer: out='LLB-G-V-W-'
|-
|-
|dm||char[4]||98||‘LLLL’||Each char is responsible for the type of a particular channel
|dm||char[4]||98||‘LLLL’||Svaki znak je odgovoran za tip određenog kanala
*‘g’ – use like halogen dimer-lamp
*‘g’ – koristi se kao halogena dimer lampa
*‘s’ – Soft Switch, lamp, when on/off power is supplied/deenergised smoothly (500msec)
*’s’ – meki prekidač, lampa, kada se napajanje/isključenje nesmetano dovodi/isključuje (500 ms)
*‘k’ – Switch, lamp, when on/off power is supplied/deenergised immediately
*‘k’ – Prekidač, lampa, kada se napajanje uključi/isključi odmah
*‘l’ – LED Function, dimmable LED lamps
*‘l’ – LED funkcija, LED lampe koje se mogu prigušiti
*‘v’ – linear Function of dimming
*‘v’ – linearna funkcija zatamnjivanja
*‘-‘ – Channel disabled
*‘-‘ – Kanal je onemogućen
*‘+’ – Regular channel
*‘+’ – Redovan kanal
Primer: dm=’skl-‘
|-
|-
|def||integer 0-250||11-14||100||The default brightness level in case of a power reset (1..250). Example: def=250
|def||integer 0-250||11-14||100||Podrazumevani nivo osvetljenosti u slučaju resetovanja napajanja (1..250). Primer: def=250
|-
|-
|min||integer 0-100||11-14||0||Minimum dimming level, example: min=10
|min||integer 0-100||11-14||0||Minimalni nivo zatamnjenja, primer: min=10
|-
|-
|max||integer 0-100||11-14||100||Maximum dimming level, example max=95
|max||integer 0-100||11-14||100||Maksimalni nivo zatamnjenja, primer max=95
|-
|-
|start||integer 0-100||11-14||0||The Start function is used for lamps that lack the minimal voltage to get turned on. If the set value is lower than the start value, the lamp is turned on at the start value and them the light is dimmed down to the set level. Example: start=60
|start||integer 0-100||11-14||0||Funkcija Start se koristi za lampe kojima nedostaje minimalni napon da bi se uključili. Ako je podešena vrednost niža od početne vrednosti, lampa se uključuje na početnoj vrednosti i njima se svetlo prigušuje do podešenog nivoa. Primer: start=60
|-
|-
|force||integer 0-100||11-14||10||Time duration of the starting value (measured in milliseconds). Example: force=20
|force||integer 0-100||11-14||10||Vremensko trajanje početne vrednosti (mereno u milisekundama). Primer: force=20
|-
|-
|runtime||integer 0-60000||11-14||1000||Runtime is the speed of changing the brightness from ‘min’ to ‘max’ (measured in milliseconds). Example: runtime=1000
|runtime||integer 0-60000||11-14||1000||Vreme rada je brzina promene svetline sa „min“ na „maks“ (mereno u milisekundama). Primer: runtime=1000
|-
|-
|offset||integer (+/- 0…39)||39-46||'0'||sensor values offset; For example, offset is -3.8 :
|offset||integer (+/- 0…39)||39-46||'0'||pomak vrednosti senzora; Na primer, ofset je -3,8:
Primer: hw="offset='-3.8'"
|-
|-
|in||char[24]||98||'BBBBBBBBBBBBMMMLLLKKKKKK'||Each char is responsible for the type of a particular channel
|in||char[24]||98||'BBBBBBBBBBBBMMMLLLKKKKKK'||Svaki znak je odgovoran za tip određenog kanala
*'B'-Button;
*'B'-dugme;
*'C'-nButton;
*'C'-nButton;
*'S'-Switch;
*'S'-Svitch;
*'K'-Contact;
*'K'-Kontakt;
*'H'-nContact;
*'H'-nContact;
*‘L’-Leak, Built-in floor (EW-WL) or on-the-floor (FW-WL) leakage sensor
* „L“-curenje, ugrađeni pod (EV-VL) ili na podu (FV-VL) senzor curenja
*‘N’-Third party leakage sensor;
*‘N’-Senzor curenja treće strane;
*'M'-Motion, motion sensor;
*'M'-Motion, senzor pokreta;
*'V'-nMotion, motion sensor;
*'V'-nMotion, senzor pokreta;
*'-'-none
*'-'-nijedan
Primer: in='MMMMMMMMMMMMLLLLLLLLLLLLLL'
12 motion sensors and 12 leak-sensors;
12 senzora pokreta i 12 senzora curenja;
in='BBBBBBBBSSSSSSBBBBSSSSSS'
in='BBBBBBBBSSSSSSBBBBSSSSSS'
12 buttons; 12 switches.
12 dugmadi; 12 prekidača.
|}
|}