editor, Interface administrators, Administrators, translation-admin, translator
9,706
edits
Changes
mLine 233:
Line 233: + + Line 283:
Line 285: + Line 303:
Line 306: − + Line 309:
Line 312: − + Line 428:
Line 431: − + + Line 438:
Line 442: + Line 640:
Line 645: + Line 653:
Line 659: − + + + + + + + + +
Add HW table
<nowiki>*</nowiki> – Output channels should only be connected using amplifier which uses 5V PWM signal from IO output as input
<nowiki>*</nowiki> – Output channels should only be connected using amplifier which uses 5V PWM signal from IO output as input
<!--T:89-->
<nowiki>**</nowiki> – installing additional power supply units is required for long lines; the maximum length of the line may be reduced by various interference factors
<nowiki>**</nowiki> – installing additional power supply units is required for long lines; the maximum length of the line may be reduced by various interference factors
<!--T:90-->
<nowiki>***</nowiki> – Only for Metaforsa 3.plus
<nowiki>***</nowiki> – Only for Metaforsa 3.plus
*connector (7) — expansion module connection.
*connector (7) — expansion module connection.
<!--T:91-->
The physical configuration and contact point assignment of each connector are shown in '''table 2'''.
The physical configuration and contact point assignment of each connector are shown in '''table 2'''.
|[[File:IOC_CONN.png|80px|frameless]] ||In1-14, In15-28 GND|| Controlling devices connection (buttons, LED buttons, magnetic reed switches, motion detectors, leakage sensors, temperature sensors, etc.): <br>In1 … In28 — logic inputs <br>GND — common
|[[File:IOC_CONN.png|80px|frameless]] ||In1-14, In15-28 GND|| Controlling devices connection (buttons, LED buttons, magnetic reed switches, motion detectors, leakage sensors, temperature sensors, etc.): <br>In1 … In28 — logic inputs <br>GND — common
|-
|-
|[[File:Can.jpg|80px|frameless]] ||VCC<br>GND<br>L<br>H|| External modules connection for CAN-bus<br>VСС — 12V output for external devices power supply<br>GND — common<br>L — CAN-L data bus<br>H — CAN-H data bus
|[[File:Can.jpg|80px|frameless]] ||VCC<br>GND<br>L<br>H|| External modules connection for CAN-bus<br>VСС — 24V output for external devices power supply<br>GND — common<br>L — CAN-L data bus<br>H — CAN-H data bus
|}
|}
{{indicationmfold}}
{{indicationmfold}}
===System installation and assembly=== <!--T:31-->
===System installation and assembly=== <!--T:31-->
Before connecting the system, you must:
Before connecting the system, you must:
====Connection of motion sensors/leakage sensors==== <!--T:54-->
====Connection of motion sensors/leakage sensors==== <!--T:54-->
The motion sensors/leakage sensors should be connected to any free input in1-in28; in these conditions their power is connected to the contact points of +12V and GND of the relevant group. The example of connection is shown in '''Fig.11'''.
<!--T:92-->
The motion sensors/leakage sensors should be connected to any free input in1-in28; in these conditions their power is connected to the contact points of +5V and GND of the relevant group. The example of connection is shown in '''Fig.11'''.
<!--T:55-->
<!--T:55-->
====Connection of buttons/switches/magnetic reed switches==== <!--T:56-->
====Connection of buttons/switches/magnetic reed switches==== <!--T:56-->
<!--T:93-->
Buttons and reed switches are connected to any free input in1-in28, while their second contact point is connected to GND point of the relevant METAFORSA module group. The example of connection is shown in '''Fig. 12-13'''.
Buttons and reed switches are connected to any free input in1-in28, while their second contact point is connected to GND point of the relevant METAFORSA module group. The example of connection is shown in '''Fig. 12-13'''.
*'z' - WS2812B -string
*'z' - WS2812B -string
<!--T:94-->
*'e' - led-button inverse
*'e' - led-button inverse
*'d' - led-button
*'d' - led-button
*'r' - thermo-resistor
*'r' - thermo-resistor
*'t' - DALLAS
*'t' - DALLAS
*'-' - none
*'-' - none
Example: io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'
Example: io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'
|-
|hw||string||98||-||hw="...", where
*pwm_invert – PWM inverting [1, 0];
*lbn_bright – brightness of led buttons, range (0 - 255);
*f – by default PWM frequency is 1000, range (1 - 5000).
Example:
<syntaxhighlight lang="xml" line>
hw="io='4---zdd----t--' pwm_invert=1 lbn_bright=255 f=1000"
</syntaxhighlight>
|-
|-
|colspan="3"|'''Only for Metaforsa 3.plus'''
|colspan="3"|'''Only for Metaforsa 3.plus'''