editor, Interface administrators, Administrators, translation-admin, translator
9,706
edits
Changes
Created page with "*'e' - LED-dugme inverzno *'d' - LED-dugme *'c' - dugme obrnuto *'b' - dugme *'s' - prekidač *'k' - kontakt inverzan *'h' - kontakt *'l' - curenje *'n' - Neptun *'v' - inverz..."
*'z' - WS2812B -string
*'z' - WS2812B -string
*'e' - led-button inverse
*'e' - LED-dugme inverzno
*'d' - led-button
*'d' - LED-dugme
*'c' - button inverse
*'c' - dugme obrnuto
*'b' - button
*'b' - dugme
*'s' - switch
*'s' - prekidač
*'k' - contact inverse
*'k' - kontakt inverzan
*'h' - contact
*'h' - kontakt
*'l' - leak
*'l' - curenje
*'n' - Neptun
*'n' - Neptun
*'v' - motion inverse
*'v' - inverzno kretanje
*'m' - motion
*'m' - pokret
*'r' - thermo-resistor
*'r' - termo-otpornik
*'t' - DALLAS
*'t' - DALLAS
*'-' - none
*'-' - nijedan
primjer: io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'
|-
|-
|hw||string||98||-||hw="...", where
|hw||string||98||-||hw="...", gdje
*pwm_invert – PWM inverting [1, 0];
*pwm_invert – PWM invertiranje [1, 0];
*lbn_bright – brightness of led buttons, range (0 - 255);
*lbn_bright – svjetlina LED dugmadi, raspon (0 - 255);
*f – by default PWM frequency is 1000, range (1 - 5000).
*f – po defaultu PWM frekvencija je 1000, raspon (1 - 5000).
primjer:
<syntaxhighlight lang="xml" line>
<syntaxhighlight lang="xml" line>
hw="io='4---zdd----t--' pwm_invert=1 lbn_bright=255 f=1000"
hw="io='4---zdd----t--' pwm_invert=1 lbn_bright=255 f=1000"
</syntaxhighlight>
</syntaxhighlight>
|-
|-
|colspan="3"|'''Only for Metaforsa 3.plus'''
|colspan="3"|'''Samo za Metaforsa 3.plus'''
|-
|-
|cfg||string||98||9600/8N1||cfg='SPEED/BPS', where
|cfg||string||98||9600/8N1||cfg='SPEED/BPS', gdje
*SPEED – baud rate [1200..115200];
*SPEED – brzina prijenosa [1200..115200];
*B – data length [7,8];
*B – dužina podataka [7,8];
*P – presence and type of parity bit [N(No parity),E(Even parity),O(Odd parity)];
*P – prisustvo i tip bita parnosti [N(Bez parnosti),E(Parni paritet),O(Neparni paritet)];
*S – stop bit length [1, 1.5 or 2].
*S – dužina stop bita [1, 1.5 ili 2].
primjer:
<syntaxhighlight lang="xml" line>
<syntaxhighlight lang="xml" line>
hw="cfg='9600/8N1'"
hw="cfg='9600/8N1'"
</syntaxhighlight>
</syntaxhighlight>
|-
|-
|[Protocol]||string||98||—||Protocol setting is described by protocol parameter. The following
|[Protocol]||string||98||—||Podešavanje protokola je opisano parametrom protokola. Sljedeće
protokoli su podržani:
*'modbus', Modbus protocol, at the end of redirection the checksum CRC16(Modbus) is added;
*'modbus', Modbus protokol, na kraju preusmjeravanja se dodaje kontrolni zbroj CRC16(Modbus);
*'dmx', DMX protocol;
*'dmx', DMX protokol;
*'CO2' for connecting Larnitech CO2 sensors;
*'CO2' za povezivanje Larnitech CO2 senzora;
*'salda' for connecting Salda ventilation.
*'salda' za spajanje Salda ventilacije.
primjer:
<syntaxhighlight lang="xml" line>
<syntaxhighlight lang="xml" line>
hw="cfg='9600/8N1' modbus"
hw="cfg='9600/8N1' modbus"
</syntaxhighlight>
</syntaxhighlight>
|-
|-
|echo||on; off||98||'off'||For settings check out and testing echo parameter can be used. Module
|echo||on; off||98||'off'||Za provjeru postavki i testiranje parametar eho se može koristiti. Modul
echo-reply can be turned on or off with the help of this parameter.Echo parameter value:
echo-reply se može uključiti ili isključiti uz pomoć ovog parametra. Vrijednost parametra Echo:
*'off'
*'isključeno'
*'on'
*'na'
primjer:
<syntaxhighlight lang="xml" line>
<syntaxhighlight lang="xml" line>
hw="cfg='9600/8N1' echo='off'"
hw="cfg='9600/8N1' echo='off'"