editor, Interface administrators, Administrators, translation-admin, translator
9,706
edits
Changes
Created page with "*'e' - LED dugme inverzno *'d' - LED dugme *'c' - dugme obrnuto *'b' - dugme *'s' - prekidač *'k' - kontakt inverzan *'h' - kontakt *'l' - curenje *'n' - Neptun *'v' - inverz..."
*'z' - VS2812B -string
*'z' - VS2812B -string
*'e' - led-button inverse
*'e' - LED dugme inverzno
*'d' - led-button
*'d' - LED dugme
*'c' - button inverse
*'c' - dugme obrnuto
*'b' - button
*'b' - dugme
*'s' - switch
*'s' - prekidač
*'k' - contact inverse
*'k' - kontakt inverzan
*'h' - contact
*'h' - kontakt
*'l' - leak
*'l' - curenje
*'n' - Neptun
*'n' - Neptun
*'v' - motion inverse
*'v' - inverzno kretanje
*'m' - motion
*'m' - pokret
*'r' - thermo-resistor
*'r' - termo-otpornik
*'t' - DALLAS
*'t' - DALLAS
*'-' - none
*'-' - nijedan
Primer: io='KKKKKKKKKKKKKKKKKKKKKKKKKKKK'
|-
|-
|hw||string||98||-||hw="...", where
|hw||string||98||-||hw="...", gde
*pwm_invert – PWM inverting [1, 0];
*pvm_invert – PVM invertovanje [1, 0];
*lbn_bright – brightness of led buttons, range (0 - 255);
*lbn_bright – osvetljenost LED tastera, opseg (0 - 255);
*f – by default PWM frequency is 1000, range (1 - 5000).
*f – podrazumevano je PVM frekvencija 1000, opseg (1 - 5000).
Primer:
<syntaxhighlight lang="xml" line>
<syntaxhighlight lang="xml" line>
hw="io='4---zdd----t--' pwm_invert=1 lbn_bright=255 f=1000"
hw="io='4---zdd----t--' pwm_invert=1 lbn_bright=255 f=1000"
</syntaxhighlight>
</syntaxhighlight>
|-
|-
|colspan="3"|'''Only for Metaforsa 3.plus'''
|colspan="3"|'''Samo za Metaforsa 3.plus'''
|-
|-
|cfg||string||98||9600/8N1||cfg='SPEED/BPS', where
|cfg||string||98||9600/8N1||cfg='SPEED/BPS', gde
*SPEED – baud rate [1200..115200];
*SPEED – brzina prenosa [1200..115200];
*B – data length [7,8];
*B – dužina podataka [7,8];
*P – presence and type of parity bit [N(No parity),E(Even parity),O(Odd parity)];
*P – prisustvo i tip bita parnosti [N(bez parnosti),E(parni paritet),O(neparni paritet)];
*S – stop bit length [1, 1.5 or 2].
*S – dužina stop bita [1, 1,5 ili 2].
Primer:
<syntaxhighlight lang="xml" line>
<syntaxhighlight lang="xml" line>
hw="cfg='9600/8N1'"
hw="cfg='9600/8N1'"
</syntaxhighlight>
</syntaxhighlight>
|-
|-
|[Protocol]||string||98||—||Protocol setting is described by protocol parameter. The following
|[Protocol]||string||98||—||Podešavanje protokola je opisano parametrom protokola. Sledeće
protokoli su podržani:
*'modbus', Modbus protocol, at the end of redirection the checksum CRC16(Modbus) is added;
*'modbus', Modbus protokol, na kraju preusmeravanja se dodaje kontrolni zbir CRC16(Modbus);
*'dmx', DMX protocol;
*'dmk', DMKS protokol;
*'CO2' for connecting Larnitech CO2 sensors;
*'CO2' za povezivanje Larnitech CO2 senzora;
*'salda' for connecting Salda ventilation.
*'salda' za povezivanje Salda ventilacije.
Primer:
<syntaxhighlight lang="xml" line>
<syntaxhighlight lang="xml" line>
hw="cfg='9600/8N1' modbus"
hw="cfg='9600/8N1' modbus"
</syntaxhighlight>
</syntaxhighlight>
|-
|-
|echo||on; off||98||'off'||For settings check out and testing echo parameter can be used. Module
|echo||on; off||98||'off'||Za proveru podešavanja i testiranje eho parametar se može koristiti. Modul
echo-reply can be turned on or off with the help of this parameter.Echo parameter value:
echo-repli se može uključiti ili isključiti uz pomoć ovog parametra. Vrednost parametra Echo:
*'off'
*'van'
*'on'
*'na'
Primer:
<syntaxhighlight lang="xml" line>
<syntaxhighlight lang="xml" line>
hw="cfg='9600/8N1' echo='off'"
hw="cfg='9600/8N1' echo='off'"