Changes

|Number of discrete inputs || 24

|Number of discrete inputs || 24

|-  

|-  

|Number of digital inputs || 4  

|Number of digital inputs || 4 (up to 8 FW-TS sensors)

|-

|-

|Current maximum rating on the direct-current voltage connectors || 50mA  

|Current maximum rating on the direct-current voltage connectors || 50mA  

{| class="wikitable" style="width:800px";

{| class="wikitable" style="width:800px";

|-

|-

|[[File:lamps.png|350px|lamp]]<br>'''Fig. 4'''|| style="margin:20px"|Such actuators as light, electric contactor, heating thermal actuator should be switched on any of the outputs 1 – 10, the neutral wire and the ground wire should be connected directly to the switchboard. The example of connection is shown in '''Fig.4'''.

|[[File:lamps.png|350px|lamp]]<br>'''Fig. 4'''|| style="margin:20px"|Such actuators as light, electric contactor, heating thermal actuator should be switched on any of the outputs 1 – 12, the neutral wire and the ground wire should be connected directly to the switchboard. The example of connection is shown in '''Fig.4'''.

|}

|}

====Connection of high load device====

====Connection of high load device====

|colspan="2" style="background-color:#dededf" |'''Caution: Before applying power to the load, make sure that the output configuration of METAFORSA module is correct. The incorrect configuration or incorrect connection can cause the module failure and/or failure of the equipment connected to it, and even a fire.'''

|colspan="2" style="background-color:#dededf" |'''Caution: Before applying power to the load, make sure that the output configuration of METAFORSA module is correct. The incorrect configuration or incorrect connection can cause the module failure and/or failure of the equipment connected to it, and even a fire.'''

|-

|-

|[[File:1pvalve.png|350px|valve]]<br>'''Fig. 5'''|| style="margin:20px"|The single pole water/gas supply valve is connected to any of the outputs of 1 – 10, the (neutral wire and the ground wire are connected directly to the switchboard. The example of connection is shown in '''Fig.5'''.

|[[File:1pvalve.png|350px|valve]]<br>'''Fig. 5'''|| style="margin:20px"|The single pole water/gas supply valve is connected to any of the outputs of 1 – 12, the (neutral wire and the ground wire are connected directly to the switchboard. The example of connection is shown in '''Fig.5'''.

|}

|}

====Connection of double-pole water/gas supply valve====

====Connection of double-pole water/gas supply valve====

#Install the module in the switchboard on the DIN-rail and fix it with the special latch on the module base.

#Install the module in the switchboard on the DIN-rail and fix it with the special latch on the module base.

#Fasten the supply unit on the left side of the module.

#Fasten the supply unit on the left side of the module.

#Connect the connector (4) having the noise filter pre-installed which is supplied complete with the module.

#Connect the connector (3) having the noise filter pre-installed which is supplied complete with the module.

#Connect the connectors (5), (6).

#Connect the connectors (4-7).

#Connect the connectors (1), (2).

#Connect the connectors (1).

#Connect the connector (3).

#Connect the connector (2).

#Apply power to the supply unit of METAFORSA module.

#Apply power to the supply unit of METAFORSA module.

#Wait until the module is loaded, then configure it in accordance with the '''System Setup Instructions.'''

#Wait until the module is loaded, then configure it in accordance with the '''System Setup Instructions.'''

#Apply power to the connectors (1), (2).

#Apply power to the connectors (1).

#Check all equipment for proper operation.

#Check all equipment for proper operation.