Difference between revisions of "Satel integration"

From Larnitech wiki page
Jump to navigation Jump to search
(Created page with "Security - SATEL installation & configuration ==SATEL Keypad - Preparing to integration== #Connect ethernet cable to your TCP module. #Enter the service code (by default 12345...")
 
Line 29: Line 29:
 
<br>'''Connection error log example:'''<br>
 
<br>'''Connection error log example:'''<br>
  
Connecting to server: 192.168.1.223:7090
+
Connecting to server: 192.168.1.223:7090
Establishing connection
+
Establishing connection
Module: ETHM-1 V2.07
+
Module: ETHM-1 V2.07
Wrong panel identifier - '''Wrong INTEGRA Ident.'''
+
Wrong panel identifier - '''Wrong INTEGRA Ident.'''
  
Hanged up.
+
Hanged up.
  
Connecting to server: 192.168.1.223:7090
+
Connecting to server: 192.168.1.223:7090
Establishing connection
+
Establishing connection
Module: ETHM-1 V2.07
+
Module: ETHM-1 V2.07
Wrong PC identifier  - '''Wrong DLOADX Ident. or GUARDX Ident.'''
+
Wrong PC identifier  - '''Wrong DLOADX Ident. or GUARDX Ident.'''
 
+
Hanged up.
Hanged up.
 
  
 
</li>
 
</li>

Revision as of 14:00, 23 November 2021

Security - SATEL installation & configuration

SATEL Keypad - Preparing to integration

  1. Connect ethernet cable to your TCP module.
  2. Enter the service code (by default 12345) and press [*].
  3. Select the item SERVICE MODE from the list and press the [#] or [X] key.
  4. Select Configuration from the list and press the [#] or [X] key.
  5. Select INTEGRA Ident.
  6. Write down the code and repeat the same for DloadX Ident. and GuadX Ident.
  7. Exit from Configuration page, and Select Structure page/Modules/LCD-Keypads/Setup/
  8. Select your TCP module from the list and press the [#] or [X] key.
  9. Select Key (DloadX)
  10. Write down the code

SATEL - DloadX

  1. When the program starts, it will ask you to enter a password. Default password 1234
  2. Select Communication/Connection Settings page

    Satel1.png

  3. Fill in the fields similar to the screenshot below. Use identifiers obtained from the panel, IP address of your SATEL module.

    Satel2.png

  4. Select Connection/ TCP/IP: DLOADX -> ETHM (You can use different options for connection). Click ‘Connect’
    Connection error log example:
    Connecting to server: 192.168.1.223:7090 Establishing connection Module: ETHM-1 V2.07 Wrong panel identifier - Wrong INTEGRA Ident. Hanged up. Connecting to server: 192.168.1.223:7090 Establishing connection Module: ETHM-1 V2.07 Wrong PC identifier - Wrong DLOADX Ident. or GUARDX Ident. Hanged up.
  5. You can find your connection settings there after reading data from the TCP module. Check that you have similar settings.

    Satel3.png



    Satel4.png



    Satel5.pngSatel6.png

  6. Example of configuration default NO - normally open reed switch


Open Structure settings



Satel7.png


Create Partition



Satel8.png

Create zone/device



Satel9.png


Larnitech Security Plugin configuration:

  1. Make sure you have SATEL licenses

    Satel10.png

  2. Make sure you have the latest versions of LT Setup, LT Server, Security plugin installed

    Satel11.png

  3. Configure plugin and enable.

    Satel12.png

  4. Select the Satel page, fill in the fields similar to the screenshot below and enable the integration

    Satel13.jpg

    IP: Your Satel TCP module Port: Integration port. Default: 7094 c



How does integration work?

Our plugin is just a receiver for Satel data, we send only a couple commands like Reset alarms, pin, arm and disarm. But the logic of these commands are processed by Satel.