Line 1: |
Line 1: |
| <languages/> | | <languages/> |
− | Security - SATEL installation & configuration
| + | Установка и настройка средств безопасности SATEL |
− | ==SATEL Keypad - Preparing to integration== | + | ==Клавиатура SATEL - Подготовка к интеграции== |
− | #Connect ethernet cable to your TCP module. | + | #Подключите кабель Ethernet к модулю TCP. |
− | #Enter the service code (by default 12345) and press [*]. | + | #Введите сервисный код (по умолчанию 12345) и нажмите [*]. |
− | #Select the item SERVICE MODE from the list and press the [#] or [X] key. | + | #Выберите из списка пункт СЕРВИСНЫЙ РЕЖИМ (SERVICE MODE) и нажмите клавишу [#] или [X]. |
− | #Select Configuration from the list and press the [#] or [X] key. | + | #Выберите из списка пункт Конфигурация (Configuration) и нажмите клавишу [#] или [X]. |
− | #Select INTEGRA Ident. | + | #Выберите INTEGRA Ident. |
− | #Write down the code and repeat the same for DloadX Ident. and GuadX Ident. | + | # Запишите код и повторите то же самое для пунктов DloadX Ident. и GuadX Ident. |
− | #Exit from Configuration page, and Select Structure page/Modules/LCD-Keypads/Setup/ | + | #Выйдите со страницы конфигурации и выберите страницу Структура/Модули/ЖК-клавиатуры/Настройка/ (Structure/Modules/LCD-Keypads/Setup/) |
− | #Select your TCP module from the list and press the [#] or [X] key. | + | #Выберите ваш модуль TCP из списка и нажмите клавишу [#] или [X]. |
− | #Select Key (DloadX) | + | #Выберите ключ (DloadX) |
− | #Write down the code | + | #Запишите код |
| | | |
| ==SATEL - DloadX== | | ==SATEL - DloadX== |
| <ol> | | <ol> |
− | <li>When the program starts, it will ask you to enter a password. Default password 1234 | + | <li>При запуске программа попросит вас ввести пароль. Пароль по умолчанию 1234 |
− | </li>
| |
| | | |
− | <li>Выберите страницу настроек связи/подключенияSelect Communication/Connection Settings page | + | <li>Выберите страницу Настройки связи/подключения (Communication/Connection Settings) |
| <br>[[file:satel1.png|700px]]<br> | | <br>[[file:satel1.png|700px]]<br> |
| </li> | | </li> |
| | | |
− | <li>Заполните поля, как показано на скриншоте ниже. Используйте идентификаторы, полученные от панели, IP-адрес вашего модуля SATEL.Fill in the fields similar to the screenshot below. Use identifiers obtained from the panel, IP address of your SATEL module. | + | <li>Заполните поля, как показано на скриншоте ниже. Используйте идентификаторы, полученные от панели, IP-адрес вашего модуля SATEL. |
| <br>[[file:satel2.png|700px]]<br> | | <br>[[file:satel2.png|700px]]<br> |
| </li> | | </li> |
| | | |
− | <li><li>Выберите Соединение/ TCP/IP: DLOADX -> ETHM (вы можете использовать разные варианты подключения). Нажмите «Подключиться» Select Connection/ TCP/IP: DLOADX -> ETHM (You can use different options for connection). Click ‘Connect’ | + | <li><li>Выберите тип подключения Connection/TCP/IP: DLOADX -> ETHM (вы можете использовать разные варианты подключения). Нажмите кнопку Подключиться (Connect). |
| | | |
| <div> | | <div> |
− | '''Connection error log example:'''
| + | '''Пример записи об ошибке соединения в файле отчета:''' |
− | Connecting to server: 192.168.1.223:7090
| + | Подключение к серверу: 192.168.1.223:7090 |
− | Establishing connection
| + | Установка соединения |
− | Module: ETHM-1 V2.07
| + | Модуль: ETHM-1 V2.07 |
− | Wrong panel identifier - '''Wrong INTEGRA Ident.'''
| + | Неверный идентификатор панели - '''Неверный идентификатор INTEGRA''' |
| | | |
− | Hanged up. | + | Разрыв соединения |
| | | |
− | Connecting to server: 192.168.1.223:7090 | + | Подключение к серверу: 192.168.1.223:7090 |
− | Establishing connection
| + | Установка соединения |
− | Module: ETHM-1 V2.07
| + | Модуль: ETHM-1 V2.07 |
− | Wrong PC identifier - '''Wrong DLOADX Ident. or GUARDX Ident.'''
| + | Неверный идентификатор ПК - '''Неверный идентификатор DLOADX. или идентификатор GUARDX.''' |
| | | |
− | Hanged up. | + | Разрыв соединения. |
| </div> | | </div> |
| </li> | | </li> |
| | | |
− | <li>You can find your connection settings there after reading data from the TCP module. Check that you have similar settings. | + | <li>Там вы можете найти настройки подключения после считывания данных из модуля TCP. Убедитесь, что у вас есть аналогичные настройки. |
| | | |
| <br>[[file:satel3.png|700px]]<br> | | <br>[[file:satel3.png|700px]]<br> |
Line 53: |
Line 52: |
| </li> | | </li> |
| | | |
− | <li>Example of configuration default NO - normally open reed switch</li> | + | <li>Пример конфигурации по умолчанию. NO — нормально открытый геркон</li> |
| </ol> | | </ol> |
| | | |
| | | |
− | '''Open Structure settings''' | + | '''Откройте Настройки структуры (Structure settings)''' |
| <br>[[file:satel7.png|700px]]<br> | | <br>[[file:satel7.png|700px]]<br> |
| | | |
| | | |
− | '''Create Partition''' | + | '''Создайте раздел''' |
| <br>[[file:satel8.png|700px]]<br> | | <br>[[file:satel8.png|700px]]<br> |
| | | |
− | '''Create zone/device''' | + | '''Создайте зону/устройство''' |
| <br>[[file:satel9.png|700px]]<br> | | <br>[[file:satel9.png|700px]]<br> |
| | | |
− | ==Larnitech Security Plugin configuration:== | + | ==Настройка плагина безопасности Larnitech:== |
| <ol> | | <ol> |
− | <li>Make sure you have SATEL licenses | + | <li>Убедитесь, что у вас есть лицензии SATEL |
| <br>[[file:satel10.png|700px]]<br> | | <br>[[file:satel10.png|700px]]<br> |
| </li> | | </li> |
| | | |
− | <li>Make sure you have the latest versions of LT Setup, LT Server, Security plugin installed | + | <li>Убедитесь, что у вас установлены последние версии программ LT Setup, LT Server, плагина безопасности |
| <br>[[file:satel11.png|700px]]<br> | | <br>[[file:satel11.png|700px]]<br> |
| </li> | | </li> |
| | | |
− | <li>Configure plugin and enable. | + | <li>Настройте и включите плагин. |
| <br>[[file:satel12.png|700px]]<br> | | <br>[[file:satel12.png|700px]]<br> |
| </li> | | </li> |
| | | |
− | <li>Select the Satel page, fill in the fields similar to the screenshot below and enable the integration | + | <li>Выберите страницу Satel, заполните поля, как показано на скриншоте ниже, и включите интеграцию. |
| <br>[[file:satel13.jpg|700px]]<br> | | <br>[[file:satel13.jpg|700px]]<br> |
| <div> | | <div> |
− | '''IP:''' Your Satel TCP module | + | '''IP:''' Ваш TCP-модуль Satel |
− | '''Port:''' Integration port. Default: 7094c | + | '''Port:''' Порт интеграции. По умолчанию: 7094c |
| </div> | | </div> |
| </ol> | | </ol> |
Line 92: |
Line 91: |
| | | |
| | | |
− | ==How does integration work?== | + | ==Как работает интеграция?== |
| | | |
− | Our plugin is just a receiver for Satel data, we send only a couple commands like Reset alarms, pin, arm and disarm. But the logic of these commands are processed by Satel.
| + | Наш плагин — это всего лишь приемник данных Satel, отправляющий только несколько команд, таких как «сбросить сигнал тревоги», «ввести пин-код», «поставить на охрану» и «снять с охраны». Алгоритм этих команд обрабатывается Satel. |