Интеграция c Satel

From Larnitech wiki page
Revision as of 11:48, 18 January 2022 by Rusanov (talk | contribs) (Created page with "Разрыв соединения")
Jump to navigation Jump to search
Other languages:
English • ‎русский

Security - SATEL installation & configuration

SATEL Keypad - Preparing to integration

  1. Connect ethernet cable to your TCP module.
  2. Enter the service code (by default 12345) and press [*].
  3. Select the item SERVICE MODE from the list and press the [#] or [X] key.
  4. Select Configuration from the list and press the [#] or [X] key.
  5. Select INTEGRA Ident.
  6. Write down the code and repeat the same for DloadX Ident. and GuadX Ident.
  7. Exit from Configuration page, and Select Structure page/Modules/LCD-Keypads/Setup/
  8. Select your TCP module from the list and press the [#] or [X] key.
  9. Select Key (DloadX)
  10. Write down the code

SATEL - DloadX

  1. When the program starts, it will ask you to enter a password. Default password 1234
  2. Выберите страницу настроек связи/подключенияSelect Communication/Connection Settings page
    Satel1.png
  3. Заполните поля, как показано на скриншоте ниже. Используйте идентификаторы, полученные от панели, IP-адрес вашего модуля SATEL.Fill in the fields similar to the screenshot below. Use identifiers obtained from the panel, IP address of your SATEL module.
    Satel2.png
  4. Выберите Соединение/ TCP/IP: DLOADX -> ETHM (вы можете использовать разные варианты подключения). Нажмите «Подключиться» Select Connection/ TCP/IP: DLOADX -> ETHM (You can use different options for connection). Click ‘Connect’
     Пример журнала ошибок соединения:
     Подключение к серверу: 192.168.1.223:7090
     Установка соединения
     Модуль: ЭТХМ-1 V2.07
     Неверный идентификатор панели - Неправильный идентификатор INTEGRA Connection error log example:
    Connecting to server: 192.168.1.223:7090
    Establishing connection
    Module: ETHM-1 V2.07
    Wrong panel identifier - Wrong INTEGRA Ident.
    
    Разрыв соединения
    
    Connecting to server: 192.168.1.223:7090
    Establishing connection
    Module: ETHM-1 V2.07
    Wrong PC identifier  - Wrong DLOADX Ident. or GUARDX Ident.
    
    Hanged up.
    
  5. You can find your connection settings there after reading data from the TCP module. Check that you have similar settings.
    Satel3.png

    Satel4.png

    Satel5.pngSatel6.png
  6. Example of configuration default NO - normally open reed switch


Open Structure settings
Satel7.png


Create Partition
Satel8.png

Create zone/device
Satel9.png

Larnitech Security Plugin configuration:

  1. Make sure you have SATEL licenses
    Satel10.png
  2. Make sure you have the latest versions of LT Setup, LT Server, Security plugin installed
    Satel11.png
  3. Configure plugin and enable.
    Satel12.png
  4. Select the Satel page, fill in the fields similar to the screenshot below and enable the integration
    Satel13.jpg
    IP: Your Satel TCP module
    Port: Integration port. Default: 7094c
    



How does integration work?

Our plugin is just a receiver for Satel data, we send only a couple commands like Reset alarms, pin, arm and disarm. But the logic of these commands are processed by Satel.