Changes

507 bytes removed ,  15:25, 21 December 2021
Line 133: Line 133:  
|colspan="2"|'''Output ports'''
 
|colspan="2"|'''Output ports'''
 
|-
 
|-
| Number of switched channels || 10
+
| Number of switched channels || 12
|-
  −
| Number of dimming channels || 4
   
|-
 
|-
 
| Commutation voltage || 0-250 V AC/DC  
 
| Commutation voltage || 0-250 V AC/DC  
Line 142: Line 140:  
|-
 
|-
 
| Peak load (device) || 160A  
 
| Peak load (device) || 160A  
|-
  −
| Max load per dimming channel || 0.5A (110W at 220V)
  −
|-
  −
| Dimmer type || MOSFET
  −
|-
  −
| Dimming type || trailing edge
   
|-
 
|-
 
| Power supply cable connection type || connector  
 
| Power supply cable connection type || connector  
Line 157: Line 149:  
|Number of discrete inputs || 24
 
|Number of discrete inputs || 24
 
|-  
 
|-  
|Number of digital inputs || 4  
+
|Number of digital inputs || 4 (up to 8 FW-TS sensors)
 
|-
 
|-
 
|Current maximum rating on the direct-current voltage connectors || 50mA  
 
|Current maximum rating on the direct-current voltage connectors || 50mA  
Line 219: Line 211:  
|1 || — connector for load application and power supply
 
|1 || — connector for load application and power supply
 
|-
 
|-
|2 || — connector for dimming-lamps application
+
|2 || — power connector
|-
  −
|3 || — power connector
   
|-
 
|-
|4 || — Ethernet network connector
+
|3 || — Ethernet network connector
 
|-
 
|-
|5-6 || — connectors for digital sensors and buttons/switching units
+
|4-7 || — connectors for digital sensors and buttons/switching units
 
|-
 
|-
|7 || — OneWire interface connector (for digital sensors)
+
|8 || — OneWire interface connector (for digital sensors)
 
|-
 
|-
|8 || — connector for expansion module.
+
|9 || — connector for expansion module.
 
|}
 
|}
   Line 270: Line 260:  
|}
 
|}
   −
{{Indicationmf}}
+
{{Indicationmf | hideDim=1}}
    
===System installation and assembly===  
 
===System installation and assembly===  
Line 289: Line 279:       −
Typical diagram of METAFORSA MFC-12.A module connection is shown in '''fig. 3.'''
+
Typical diagram of METAFORSA MFC-12 module connection is shown in '''fig. 3.'''
 
<div style="clear: both">[[File:Mfc12chcon.png|700px|Fig. 3]]</div>
 
<div style="clear: both">[[File:Mfc12chcon.png|700px|Fig. 3]]</div>
   Line 300: Line 290:  
{| class="wikitable" style="width:800px";
 
{| class="wikitable" style="width:800px";
 
|-
 
|-
|[[File:lamps.png|350px|lamp]]<br>'''Fig. 4'''|| style="margin:20px"|Such actuators as light, electric contactor, heating thermal actuator should be switched on any of the outputs 1 – 10, the neutral wire and the ground wire should be connected directly to the switchboard. The example of connection is shown in '''Fig.4'''.
+
|[[File:lamps.png|350px|lamp]]<br>'''Fig. 4'''|| style="margin:20px"|Such actuators as light, electric contactor, heating thermal actuator should be switched on any of the outputs 1 – 12, the neutral wire and the ground wire should be connected directly to the switchboard. The example of connection is shown in '''Fig.4'''.
 
|}
 
|}
  −
      
====Connection of high load device====
 
====Connection of high load device====
Line 323: Line 311:  
|colspan="2" style="background-color:#dededf" |'''Caution: Before applying power to the load, make sure that the output configuration of METAFORSA module is correct. The incorrect configuration or incorrect connection can cause the module failure and/or failure of the equipment connected to it, and even a fire.'''
 
|colspan="2" style="background-color:#dededf" |'''Caution: Before applying power to the load, make sure that the output configuration of METAFORSA module is correct. The incorrect configuration or incorrect connection can cause the module failure and/or failure of the equipment connected to it, and even a fire.'''
 
|-
 
|-
|[[File:1pvalve.png|350px|valve]]<br>'''Fig. 5'''|| style="margin:20px"|The single pole water/gas supply valve is connected to any of the outputs of 1 – 10, the (neutral wire and the ground wire are connected directly to the switchboard. The example of connection is shown in '''Fig.5'''.
+
|[[File:1pvalve.png|350px|valve]]<br>'''Fig. 5'''|| style="margin:20px"|The single pole water/gas supply valve is connected to any of the outputs of 1 – 12, the (neutral wire and the ground wire are connected directly to the switchboard. The example of connection is shown in '''Fig.5'''.
 
|}
 
|}
  −
      
====Connection of double-pole water/gas supply valve====
 
====Connection of double-pole water/gas supply valve====
Line 440: Line 426:  
#Install the module in the switchboard on the DIN-rail and fix it with the special latch on the module base.
 
#Install the module in the switchboard on the DIN-rail and fix it with the special latch on the module base.
 
#Fasten the supply unit on the left side of the module.
 
#Fasten the supply unit on the left side of the module.
#Connect the connector (4) having the noise filter pre-installed which is supplied complete with the module.
+
#Connect the connector (3) having the noise filter pre-installed which is supplied complete with the module.
#Connect the connectors (5), (6).
+
#Connect the connectors (4-7).
#Connect the connectors (1), (2).
+
#Connect the connectors (1).
#Connect the connector (3).
+
#Connect the connector (2).
 
#Apply power to the supply unit of METAFORSA module.
 
#Apply power to the supply unit of METAFORSA module.
 
#Wait until the module is loaded, then configure it in accordance with the '''System Setup Instructions.'''
 
#Wait until the module is loaded, then configure it in accordance with the '''System Setup Instructions.'''
#Apply power to the connectors (1), (2).
+
#Apply power to the connectors (1).
 
#Check all equipment for proper operation.
 
#Check all equipment for proper operation.
    
===METAFORSA module shut-off and deinstallation procedure===
 
===METAFORSA module shut-off and deinstallation procedure===
   −
#De-energize the module by disconnecting the circuit breaker assembly of the load power supply and METAFORSA module supply unit. Verify the voltage is absent on the terminals (1), (2) of the connector wires and on the input terminals of the supply unit.
+
#De-energize the module by disconnecting the circuit breaker assembly of the load power supply and METAFORSA module supply unit. Verify the voltage is absent on the terminals (1) of the connector wires and on the input terminals of the supply unit.
#Disconnect the load power supply connectors (1), (2).
+
#Disconnect the load power supply connectors (1).
#Disconnect the connector (3).
+
#Disconnect the connector (2).
#Disconnect the connectors (4)-(6).
+
#Disconnect the connectors (3)-(7).
 
#Remove the module from the DIN-rail, releasing the latch at the bottom of the module base.
 
#Remove the module from the DIN-rail, releasing the latch at the bottom of the module base.
   Line 567: Line 553:  
in='BBBBBBBBSSSSSSRRRRSSRRRR'
 
in='BBBBBBBBSSSSSSRRRRSSRRRR'
 
8 buttons; 8 switches and 8 LED channels.
 
8 buttons; 8 switches and 8 LED channels.
|-
  −
|rgb||char[8]||98||'RGBLRGBL'||Each char is responsible for the type of a particular channel selected as 'R' in inputs
  −
*RGB – rgb lamp (avaliable only on in15-in17; in21-in23)
  −
*L – dimmer-lamp (avaliable only on in15-in18; in21-in24)
  −
Example:
  −
hw="in='BBBBBBBBSSSSSSRRRRSSRRRR' rgb='RGBLLLLL'"
   
|}
 
|}