This module allows connecting devices with 0-10V input or output interfaces to the Smart Home system.

Module dimensions

Connection of 6 0-10V devices

Module parameters

Parameter name Value
Output channels quantity 4
Input channels quantity 2
Max load per channel 15mA
Power supply 11.5 … 27.5 V DC from CAN
Max current(24V) 50mA
Bus type CAN (4-wire)
Equipment installation type DIN-rail (EN 60715)
Case material ABS
Protection IP40
Temperature range -10 … +50 °C
Size 2U, 36x97x58 mm
Weight 130g

Indication of module operation.


Indicator Status Description
Device in bootloader
Waiting for bootloader command
Flashing firmware

Firmware mode

Indicator Status Description
Operational mode

Lost connection to server

Module installation and connection procedure

  1. Install the module in the switchboard on the DIN rail and fix it with the special latch on the module base.
  2. Connect the input/output connectors.
  3. Connect the CAN connectors.
  4. Configure the module using LT setup.
  5. Check all equipment for proper operation.

Module shut-off and deinstallation procedure

  1. Disconnect the connectors CAN.
  2. Disconnect the input/output connectors.
  3. Remove the module from the DIN rail, releasing the latch at the bottom of the module base.

HW Settings

Name Type, range SUBID Default Description
def integer 0-250 1-4 100 The default brightness level in case of a power reset (1..250). Example: def=250
min integer 0-100 1-4 0 Minimum dimming level, example: min=10
max integer 0-100 1-4 100 Maximum dimming level, example max=95
start integer 0-100 1-4 0 The Start function is used for lamps that lack the minimal voltage to get turned on. If the set value is lower than the start value, the lamp is turned on at the start value and them the light is dimmed down to the set level. Example: start=60
force integer 0-100 1-4 10 Time duration of the starting value (measured in milliseconds). Example: force=20
runtime integer 0-60000 1-4 1000 Runtime is the speed of changing the brightness from ‘min’ to ‘max’ (measured in milliseconds). Example: runtime=1000
dm char[4] 98 ‘vvvv’ Each char is responsible for the type of a particular channel

  • ‘g’ – use like halogen dimmer-lamp
  • ‘s’ – Soft Switch, lamp, when on/off power is supplied/deenergised smoothly (500msec)
  • ‘k’ – Switch, lamp, when on/off power is supplied/deenergised immediately
  • ‘l’ – LED Function, dimmable LED lamps
  • ‘v’ – linear Function of dimming
  • ‘-‘ – Channel disabled
  • ‘+’ – Regular channel
  • Example: dm=’skl-‘


	<item addr="416:1" auto-period="600" cfgid="144" name="Dimmer 1" type="dimmer-lamp"/>
		<item addr="416:2" auto-period="600" cfgid="144" name="Dimmer 2" type="dimmer-lamp"/>
		<item addr="416:3" auto-period="600" cfgid="144" name="Dimmer 3" type="dimmer-lamp"/>
		<item addr="416:4" auto-period="600" cfgid="144" name="Dimmer 4" type="dimmer-lamp"/>
		<item addr="416:31" cfgid="144" name="Voltage" system="yes" type="voltage-sensor"/>
		<item addr="416:32" cfgid="144" name="Voltage" system="yes" type="voltage-sensor"/>
		<item addr="416:97" cfgid="144" name="Temperature" system="yes" type="temperature-sensor"/>
		<item addr="416:98" cfgid="144" logic-ver="19" name="Temperature"  system="yes" type="temperature-sensor"/>