1,970
edits
Changes
Jump to navigation
Jump to search
Created page with "Security - SATEL installation & configuration ==SATEL Keypad - Preparing to integration== #Connect ethernet cable to your TCP module. #Enter the service code (by default 12345..."
Security - SATEL installation & configuration
==SATEL Keypad - Preparing to integration==
#Connect ethernet cable to your TCP module.
#Enter the service code (by default 12345) and press [*].
#Select the item SERVICE MODE from the list and press the [#] or [X] key.
#Select Configuration from the list and press the [#] or [X] key.
#Select INTEGRA Ident.
#Write down the code and repeat the same for DloadX Ident. and GuadX Ident.
#Exit from Configuration page, and Select Structure page/Modules/LCD-Keypads/Setup/
#Select your TCP module from the list and press the [#] or [X] key.
#Select Key (DloadX)
#Write down the code
==SATEL - DloadX==
<ol>
<li>When the program starts, it will ask you to enter a password. Default password 1234
</li>
<li>Select Communication/Connection Settings page
<br><br>[[file:satel1.png|700px]]<br><br>
</li>
<li>Fill in the fields similar to the screenshot below. Use identifiers obtained from the panel, IP address of your SATEL module.
<br><br>[[file:satel2.png|700px]]<br><br>
</li>
<li>Select Connection/ TCP/IP: DLOADX -> ETHM (You can use different options for connection). Click ‘Connect’
<br>'''Connection error log example:'''<br>
Connecting to server: 192.168.1.223:7090
Establishing connection
Module: ETHM-1 V2.07
Wrong panel identifier - '''Wrong INTEGRA Ident.'''
Hanged up.
Connecting to server: 192.168.1.223:7090
Establishing connection
Module: ETHM-1 V2.07
Wrong PC identifier - '''Wrong DLOADX Ident. or GUARDX Ident.'''
Hanged up.
</li>
<li>You can find your connection settings there after reading data from the TCP module. Check that you have similar settings.
<br><br>[[file:satel3.png|700px]]<br><br>
<br><br>[[file:satel4.png|700px]]<br><br>
<br><br>[[file:satel5.png|350px]][[file:satel6.png|350px]]<br><br>
</li>
<li>Example of configuration default NO - normally open reed switch</li>
</ol>
===Open Structure settings===
<br><br>[[file:satel7.png|700px]]<br><br>
===Create Partition===
<br><br>[[file:satel8.png|700px]]<br><br>
===Create zone/device===
<br><br>[[file:satel9.png|700px]]<br><br>
==Larnitech Security Plugin configuration:==
<ol>
<li>Make sure you have SATEL licenses
<br><br>[[file:satel10.png|700px]]<br><br>
</li>
<li>Make sure you have the latest versions of LT Setup, LT Server, Security plugin installed
<br><br>[[file:satel11.png|700px]]<br><br>
</li>
<li>Configure plugin and enable.
<br><br>[[file:satel12.png|700px]]<br><br>
</li>
<li>Select the Satel page, fill in the fields similar to the screenshot below and enable the integration
<br><br>[[file:satel13.jpg|700px]]<br><br>
'''IP:''' Your Satel TCP module
'''Port:''' Integration port. Default: 7094
c
</ol>
==How does integration work?==
Our plugin is just a receiver for Satel data, we send only a couple commands like Reset alarms, pin, arm and disarm. But the logic of these commands are processed by Satel.
==SATEL Keypad - Preparing to integration==
#Connect ethernet cable to your TCP module.
#Enter the service code (by default 12345) and press [*].
#Select the item SERVICE MODE from the list and press the [#] or [X] key.
#Select Configuration from the list and press the [#] or [X] key.
#Select INTEGRA Ident.
#Write down the code and repeat the same for DloadX Ident. and GuadX Ident.
#Exit from Configuration page, and Select Structure page/Modules/LCD-Keypads/Setup/
#Select your TCP module from the list and press the [#] or [X] key.
#Select Key (DloadX)
#Write down the code
==SATEL - DloadX==
<ol>
<li>When the program starts, it will ask you to enter a password. Default password 1234
</li>
<li>Select Communication/Connection Settings page
<br><br>[[file:satel1.png|700px]]<br><br>
</li>
<li>Fill in the fields similar to the screenshot below. Use identifiers obtained from the panel, IP address of your SATEL module.
<br><br>[[file:satel2.png|700px]]<br><br>
</li>
<li>Select Connection/ TCP/IP: DLOADX -> ETHM (You can use different options for connection). Click ‘Connect’
<br>'''Connection error log example:'''<br>
Connecting to server: 192.168.1.223:7090
Establishing connection
Module: ETHM-1 V2.07
Wrong panel identifier - '''Wrong INTEGRA Ident.'''
Hanged up.
Connecting to server: 192.168.1.223:7090
Establishing connection
Module: ETHM-1 V2.07
Wrong PC identifier - '''Wrong DLOADX Ident. or GUARDX Ident.'''
Hanged up.
</li>
<li>You can find your connection settings there after reading data from the TCP module. Check that you have similar settings.
<br><br>[[file:satel3.png|700px]]<br><br>
<br><br>[[file:satel4.png|700px]]<br><br>
<br><br>[[file:satel5.png|350px]][[file:satel6.png|350px]]<br><br>
</li>
<li>Example of configuration default NO - normally open reed switch</li>
</ol>
===Open Structure settings===
<br><br>[[file:satel7.png|700px]]<br><br>
===Create Partition===
<br><br>[[file:satel8.png|700px]]<br><br>
===Create zone/device===
<br><br>[[file:satel9.png|700px]]<br><br>
==Larnitech Security Plugin configuration:==
<ol>
<li>Make sure you have SATEL licenses
<br><br>[[file:satel10.png|700px]]<br><br>
</li>
<li>Make sure you have the latest versions of LT Setup, LT Server, Security plugin installed
<br><br>[[file:satel11.png|700px]]<br><br>
</li>
<li>Configure plugin and enable.
<br><br>[[file:satel12.png|700px]]<br><br>
</li>
<li>Select the Satel page, fill in the fields similar to the screenshot below and enable the integration
<br><br>[[file:satel13.jpg|700px]]<br><br>
'''IP:''' Your Satel TCP module
'''Port:''' Integration port. Default: 7094
c
</ol>
==How does integration work?==
Our plugin is just a receiver for Satel data, we send only a couple commands like Reset alarms, pin, arm and disarm. But the logic of these commands are processed by Satel.