Changes

Updating to match new version of source page
<languages/>
1. Open LT Setup, General tab, click on Plugins<br>
[[File:Screenshot 1.png|250px]]<br>
2. Find Security plugin, click on Enable button to launch it <br>
[[File:02.png|900px]]<br>
3. Then click on Configure button
[[File:03.png|900px]]<br>
4. Click on +Add zone, to set actions for alarm settings<br>
[[File:04.png|350px]]<br>
5. Zone name - any you like, but to understand what system/sensors you will use<br>
[[File:05.png|400px]]<br>
6. You can add different zones. All added scenarios will appear below<br>
[[File:06.png|300px]]<br>
7. Then click on +Add device button, to add responsible sensors for the action<br>
[[File:07.png|600px]]<br>
8. In pop-up window set sensor and settings for it and save changes<br>
*Device type - set Arm<br>
*Device - choose you sensor<br>
*Name - sensors name in security plugin<br>
*Recovery timeout - time in seconds, when sensor resets after an alarm is triggered, until the problem disappears (door closing, no movement)<br>
*Level for alarm - range of values 1-100 for motion sensors<br>
[[File:08.png|600px]]<br>
9. To watch, what the sensor is responsible for action, click on the folder. You can add some sensors into a zone<br>
For all other zones, identic procedure<br>
[[File:09.png|400px]]<br>
10. After settings of zones, you need to add at least one user, create a password, and set the permissions for the user<br>
Click on the Users tab, and then on +Add<br>
[[File:10.png|500px]]<br>
11. In pop-up window, made a settings for the user, and save changes<br>
[[File:11.png|250px]]
[[File:12.png|700px]]<br>
12. After the creation of the user, the Security plugin becomes available in-app<br>
Open the app, click on the wi-fi icon, then on the Security icon. Will open the window with pin code confirmation<br>
Enter the pin you created for user, and then Ok<br>
[[File:13.png|400px]]
[[File:14.png|300px]]<br>
13. In Home tab, you will see your zones, and after clicking on the right corner icon, the sensors that you set<br>
[[File:15.png|300px]]<br>
14. In Security tab, you will see the widget<br>
[[File:16.png|250px]]<br>
*ARM - full arming of the house with your zones<br>
[[File:17.png|300px]]<br>
*Partial ARM - you can choose one or some zones for arming<br>
[[File:18.png|350px]]<br>
*Disarm - disarming the house<br>
[[File:19.png|300px]]<br>
*Armed - house under protection<br>
[[File:20.png|300px]]<br>
*Alarm - when sensors are triggering, the widget will turn Red and push-notification sent to your phone<br>
[[File:21.png|350px]]
[[File:22.png|350px]]<br>
*To reset the sensors, click on Alarm button, Reset sensors and Ok<br>
[[File:23.png|350px]]<br>
15. Also, you can set the scenarios for the Partial arm. For that, you need to go settings of the Security plugin<br>
On your zone, click on +Add device<br>
[[File:24.png|600px]]<br>
16. In pop-up window, click on Device type - in drop-down list choose Arm<br>
New fields will be appears<br>
[[File:25.png|220px]]<br>
17. Click on +Add mode. In the new window, set any name you like, Save settings and your mode will appear below<br>
[[File:26.png|600px]]<br>
18. After that, you can set the mode for your zones. For example day/night, and Save settings<br>
[[File:27.png|250px]]<br>
19. Open app, enter in Security plugin, move to Partial arm<br>
Your modes will appear in the drop-down list<br>
[[File:28.png|350px]]<br>
20. Click on the mode you want to arm and then Ok. The system will be activated<br>
[[File:29.png|300px]]<br>
21. To see, what zones are actually enabled, click on the Home tab<br>
[[File:30.png|300px]]<br>
22. Do the same with another mode - Night, in our case. And your settings will be activated<br>
[[File:31.png|300px]]<br>
23. Check the settings in Home tab<br>
[[File:32.png|300px]]<br>
3,388

edits