Посібник із швидкого початку роботи

From Larnitech wiki page
Revision as of 15:24, 31 October 2023 by Support (talk | contribs) (Created page with "<span style="font-size: 30px; vertical-align: middle;">⑤</span> - І дві клавіші з підсвічуванням. 1000x800px <hr> Де...")
Jump to navigation Jump to search
Other languages:
Deutsch • ‎English • ‎Nederlands • ‎bosanski • ‎dansk • ‎español • ‎français • ‎italiano • ‎lietuvių • ‎magyar • ‎polski • ‎português • ‎română • ‎slovenčina • ‎čeština • ‎русский • ‎српски / srpski • ‎українська • ‎Ἀρχαία ἑλληνικὴ


Швидкий старт/розпакування.


Вітаємо всіх на нашому каналі, це відео присвячене навчанню швидкого налаштування системи Larnitech (ЛарнітЕх). Налаштування ми будемо робити на основі демонстраційного кейсу. У комплект набору для навчання входить демонстраційна валіза та коробки з додатковим приладдям . DemoCase01.png


Усередині коробки ви знайдете:

- Блок живлення з Type-C (тайп-сі) роз'ємом та підтримкою технології Power Delivery (пАуер делІвері);

- Powerbank (пАуер банк), оснащений дисплеєм і Type-C-(тайп-сі) - виходом, здатним живити демонстраційну валізу;

- TКабель Type-C (тайп-сі) з індикацією споживаної потужності;

- 2 кабелі CAN-шини (кан-шини);

- Демонстраційна плата з модулем BW-LC-02 (бі.дабл.ю-ел.синоль два), 2 світлодіоди, 4 кнопки з підсвічуванням та датчик температури, підключені до модуля. DemoCase2.png


Демонстраційна валіза містить:

Модуль Metaforsa-2 (метафОрса-два), який має:

- 10 релейних виходів із підключеними світлодіодами, які відображають їх поточний стан;

- 4 димовані канали, до яких підключені димовані світлодіоди;

- 24 входи, до яких підключено 6 кнопок і 4 перемикачі для імітації різних датчиків;

- Входи для підключення термодатчиків з одним підключеним датчиком;

- CAN-шина (кан-Шина) для додаткових пристроїв, до якої підключені інші модулі цієї валізи, а також 2 додаткові порти для зовнішніх пристроїв; DemoCase3.png


Модуль DW-IO (ді.дабл.ю-ай.оу.)

Цей модуль має 14 універсальних входів-виходів, до яких підключено:

- 4х канальну RGBW-стрічку (ар.джи.бі.дабл.ю-стрічку) підключену через підсилювач струму AMP5V-4 (емп п'ять ві чотири)  ;

- Стрічка з адресуємимі світлодіодами, кожен з яких може відображати власний колір;

- Датчик температури;

- І дві клавіші з підсвічуванням. DemoCase4.png


Демонстраційник кейс також містить:

- a Media Point FE-MP with two speakers;

- A six-in-one CW-CO2 sensor, which measures: Level of motion, Lighting, Temperature, Humidity, Level of CO2 and which has an infrared transmitter.

- a 4-inch sensor panel LCP4 which can display either a regular interface or an interface adapted for wall panels;

Inside the case there is a button control module BW-SW24 which has a six-button 24-volt JUNG keypad connected to it. And a Wi-Fi router, which can get connected to the internet either via an ethernet port on the front panel of the case or via an available Wi-Fi network. For power supply, there is a Type-C port , which is located on the front panel All the equipment installed in the demonstration suitcase is powered by 20 Volts, which is absolutely safe for the user. Connect the power cable and the Ethernet cable. If you do not have the possibility to connect via Ethernet, later in this video we will demonstrate how to connect the inbuilt router to your Wi-Fi network. DemoCase5.png


In order to proceed, the Larnitech app needs to be installed onto your smartphone or tablet. Just scan the first QR code from the top of your suitcase.

If after installing and starting the application the connection does not get established automatically, you will need to connect to Wi-Fi network ‘Larnitech_case_5G’ with the help of your mobile device. Then start the application and scan the first QR code in the ‘Connections’ section You may need to turn off data transmission on your mobile device if the demonstration set is not connected to the Internet. DemoCase6.png


The main screen of the app has several key elements. In the upper left corner there is the ‘area select’ menu . Just click one of the available areas in order to manage it . Then there are icons which let you choose the executors, sensors, climate, multimedia, remote controls and cameras . In the right corner there is an icon for the additional menu . Inside the icon you can also see the status of the current connection. DemoCase7.png


Turning the executors on or off is done with a simple click. In order to change the level of lighting , color of lights or the position of the blinds, use a double click. In order to access the status history of this executor or sensor, press and hold the icon for one second. A short press of the physical buttons on the panel turns the light on or off. Press and hold the button to change the light brightness. DemoCase08.png


In order to demonstrate the Plug and Play function, we open the executors in the Setup area and connect the module to the CAN bus. The system automatically detects the new module and adds it to the ‘Setup’ area, where we are able to control the new module instantly. DemoCase9.png


Now we can set up these executors. In order to do this, enter the additional menu and activate the edit mode, by pressing the appropriate icon . Now we are in the edit mode , which can be seen from the appropriate notification in the top part of the screen. In this mode, when we press and hold an icon, we can move it among other elements and place it into another Room by placing it in the Area-choosing Menu and then choosing the area that we need. A long press of the element starts the menu, from which we set up the current element.In the ‘General’ section we can change the name of the element, add a voice command for it, change an icon or add the element to ‘Favorites’. DemoCase10.png


‘Auto’ section lets us activate the automation with a few clicks, as well as set up its parameters.

In the ‘schedule’ section , you can determine the schedule when the given element will turn on or off, including by using the time of the setting and rising of the sun.

The ‘Switches’ tab lets you bind a button to control the executor. DemoCase11.png


In order to do this, we press the button we need to bind. The system displays it, after which we press ‘Bind’ and save the changes. Now this button controls the executor The ‘Switches’ tab also features additional button setup options. For example, we can program the executor to be controlled with a double or triple click of a button, as well as define an action performed by this, for example ‘only turning on’ or ‘only turning off’ an executor. In this case we are setting up the button to do the following: one click will cause the lamp to toggle, a double click will turn it on and a triple click will turn it off. In this way a single button can perform up to five different actions. DemoCase12.png


Let’s also set up basic automation of turning an executor on or off with the help of a motion sensor.

The ‘Auto period’ option sets the time for which the automation is disabled after an executor is manually controlled.For our demonstration purposes, we will set it to zero.

Then we will activate the automation to turn on the executor when motion is detected. We choose the motion sensor and the level of motion . We can also choose a light sensor and its parameters. DemoCase13.png


Now we will activate turning off of an executor if there is no motion: we choose the same sensor, set a lower threshold and a minimal time.Save the changes. The extra ‘A’ icon will be added to the executor icon, meaning that automation has been set up for it. Now the lamp will be turned on when motion is detected and instantly turned off when no motion is detected. DemoCase14.png


Let’s create a light scheme. For this we need to select the appropriate item in the additional menu . Give the light scheme a name . DemoCase15.png


In the ‘State’ tab, use a long press to add the lights we want to use into the light scene and set up their state . ‘Auto’, ‘Schedule’, ‘Switch’ tabs are the same for all the executors. Save the changes and we are able to use the newly-created light scheme immediately. DemoCase16.png


While you are in the Edit Mode, there is a ‘Setup’ icon in the additional menu. Here in the ‘Structure’ tab we can see all the areas. We can create new ones , rename them and move the elements around. DemoCase17.png


In the ‘Mikrotik’ tab you can see the current parameters of your router, which you can also connect to your local Wi-Fi network. In order to do this, enter the Wi-Fi sub-menu, click the wlan1 interface configuration , after which choose the ‘station’ mode, choose a Wi-Fi network out of the list of available ones and enter the connection password. DemoCase18.png


In the ‘Backups’ tab you can see the list of saved configurations, which can be restored if necessary. DemoCase19.png


For cloud access to the device, you do not need any extra settings. The app detects the absence of the system in your local network and automatically establishes the connection via the cloud. DemoCase20.jpg


We thank you for watching this tutorial! If you have questions or need extra help, please do not hesitate to refer to our technical support team. See you in the next episodes!