Metaforsa2 MF-14/da

MF-14
Output ports Number of switched channels 10 Number of dimming channels 4 Peak load 16 A Max load per dimming channel 0.5 A (110 W at 220 V) Dimmer type MOSFET
Input ports Number of discrete inputs 24 Number of digital inputs 4
General Max CAN devices 50 Max CAN bus length 800 m (twisted pair 5 cat) Max current per CAN bus 500 mA
Other Supply voltage 11.5...27.5 V DC Dimentions 9U, 156x110x58 mm

Introduktion

METAFORSA SMART HOUSE Installationsmanual beskriver proceduren for installation, montering, betjening og indstilling. Mens du arbejder med systemet, skal du nøje overholde alle kravene i denne manual. Manglende overholdelse kan resultere i beskadigelse af enheden, dens fejl, elektrisk stød, brand og andet nedfald. Producenten forbeholder sig retten til at foretage ændringer i denne manual uden forudgående varsel. Denne manual er en integreret del af systemet og forbliver hos slutbrugeren.

‎

Funktioner

• 10 universelle udgange understøtter:
  • Lys
  • NC/NO varmeventiler
  • Persienner
  • 1 eller 2-polede porte
  • 1 eller 2-polede ventiler
  • NC/NO låse
  • Blæserkonvektorer
• 4 dæmpningsudgange
• 24 diskrete indgange, der understøtter:
  • Knapper
  • Switcher
  • reed afbrydere
  • lækagesensorer
  • Bevægelsesdetektorer
• 4 digitale indgange til op til 8 temperatursensorer
• Forlængerport
• Relæer med AgSnO2-kontakter klassificeret til 80A 20ms startstrøm
• Skyforbindelse og kontrol af alle hussystemer
• Stemmestyring (Siri, Alexa, Google Home)
• Plugins-motor gør det muligt at udvide systemmulighederne (f.eks. integration med Satel, Philips Hue, IKEA lys)
• Sikkerhed mod uautoriseret indtrængen sikret med RSA/AES256-kryptering
• Push-meddelelser fra systemet på din telefon (også muligt at modtage via Telegram og Viber messengers)
• Historie (målerdata for 1 år er gemt)
• Plug and play (mulighed for hurtig og brugervenlig udvidelse af systemet)
• Regelmæssige systemopdateringer
• Stor konstant opdateret database med scripts for at opfylde alle dine behov
• Automatisk daglig backup via cloud med mulighed for at gendanne den oprindelige konfiguration
• Åben API (som gør det muligt at integrere Larnitech i andre systemer)
• Interaktiv og brugervenlig LT SETUP-webgrænseflade tilgængelig for avanceret konfiguration
• Tilslut og brug
• Det er et komplet klar til at installere Smart Home-systemsæt

Sikkerhedskrav

ADVARSEL! Alt arbejde i forbindelse med installation, tilslutning, opsætning, service og support skal udføres af kvalificeret personale med tilstrækkelige færdigheder og erfaring i at arbejde med elektrisk udstyr.

For at undgå risikoen for brand, elektrisk stød, beskadigelse af systemet og/eller personskade, skal installationen og monteringen af systemet udføres i overensstemmelse med instruktionerne nedenfor:

• alle tilslutningsarbejder skal udføres uden strøm;
• brug passende værktøj og personlig beskyttelse mod elektrisk stød;
• brug ikke beskadigede kabler, ledninger og stik;
• undgå foldning af kabler og ledninger;
• undgå at klemme eller knække kabler og ledninger ved at anvende for stor kraft. Ellers kan indvendige ledere af kablet og ledningerne blive strippet eller knækket;
• brug ikke stikkontakten med dårlige kontakter til at forbinde;
• overskrid ikke grænsen for belastningsparametre angivet i denne manual;
• forsyningsledernes ledningssektion er underlagt specifikationerne for strømtæthedsgrænse, isoleringstype og ledningsmateriale. Lyssektion kan resultere i kabeloverophedning og brand.

Når du arbejder med systemet efter spændingsforsyning ALDRIG:

• foretag tilslutning/frakobling af stik;
• åbne moduler og sensorer.

Systemkonfiguration og formål

Formål med systemet

METAFORSA SMART HOUSE er en færdiglavet løsning til automatisering af bolig- og erhvervslokaler, hotelkomplekser, som indeholder de mest eftertragtede funktioner i Smart House.

Enheden har 10 kontrolkanaler, 4 dæmpningskanaler, 24 indgående sensorkanaler og en digital sensorforbindelsesport.

Universaludgange kan bruges til at styre:	Universalindgange giver dig mulighed for at tilslutte:
Belysning	Taster/koblingsenheder
Stikstik	Magnetiske reed-kontakter
Gulvvarme	Bevægelsessensorer
Gardin-/portaktuatorer	Lækagesensorer
Vandforsyning/varmeventiler

Digitale sensorer tilslutningsport

Den digitale sensortilslutningsport giver dig mulighed for at tilslutte en række digitale sensorer, såsom temperatursensorer, omgivende lys, fugtighed og andet.

Udvidelsesport

Udvidelsesporten giver dig mulighed for at opgradere systemet ved at tilslutte ekstraudstyr, såsom styremodulet til LED-belysning, dæmpning, måleenheder og andre elementer. Pakken, som er fuldstændig klar til at installere, inkluderer den grundlæggende hardware og software.

Pakkens indhold

Pakken leveres som standard med:

Mainframe METAFORSA MF-14.А	1 stk
Strømforsyningsenhed MEANWELL DR-15-12	1 stk
Bevægelsessensor CW-MSD	3 stk
Lækagesensor FW-WL.A	2 stk
Temperaturfølsomt element FW-TS.A	4 stk
Magnetisk reed-kontakt (vindues-/dørpositionssensor)	4 stk
Ethernet-kabel støjfilter	1 stk
Strømforsyningsledning	1 stk

Grundlæggende tekniske specifikationer for systemet

De grundlæggende specifikationer og egenskaber for modulet METAFORSA MF-14.A er vist i tabel 1

Table1

Specifikation	Betyder
Outputporte
Antal skiftede kanaler	10
Antal skiftede grupper	10
Antal dæmpningskanaler	4
Kommuteringsspænding	0-250 V AC/DC
Spidsbelastning (én kanal)	16A
Spidsbelastning (enhed)	160A
Maks. belastning pr. dæmpningskanal	0,5A (110W ved 220V)
Lysdæmper type	MOSFET
Lysdæmper belastningstype	R,C
Lysdæmpningstype	bagkant
Strømforsyningskabeltilslutningstype	stik
Tilladt sektion af strømforsyningskablet til tilslutning i stikket: enkeltlederkabel flerlederkabel tilsluttet flerlederkabel	0,5 … 4mm2 0,5 … 4mm2 0,5 … 2,5 mm2
Indgangsporte
Antal diskrete input	24
Antal digitale indgange	4
Maksimal strømstyrke på jævnspændingsstikkene	50mA
Andet
Omgivelsestemperatur i drift	0 … +45°С
Opbevarings-/transporttemperatur	-20 … +60°С
Tilladt luftfugtighed	0 … 95 % (ikke-kondenserende)
Strømforsyning	12 … 27,5 V DC 24V, 0,75A anbefales
Maksimal efterspørgsel	0,5A
Tilgængelige grænseflader	Ethernet, CAN, OneWire
Bustype	CAN (4-leder)
CAN (4-leder)	800 m* (parsnoet 5 kat)
CAN ledningstype	FTP Cat 5E
CAN-forbindelsestype	stik
Maksimal længde for digital linje	30 m
Digital line wirde type	UTP/FTP Cat 5E
LAN maksimal længde	100 m
LAN-ledningstype	UTP/FTP Cat 5E
LAN-forbindelsestype	Stik RJ-45
Dimensionsspecifikationer	9U, 156x110x58 mm
Skalmateriale	ABS plast
Caring	IP40
Installationstype for udstyr	DIN-skinne (EN 60715)
Vægt	400 g

* – installation af yderligere strømforsyningsenheder er påkrævet for lange linjer; den maksimale længde af ledningen kan reduceres af forskellige interferensfaktorer

Systemets generel struktur

Modulets generelle visning er vist i fig. 1

1	— stik til belastningsanvendelse
2	— stik til dæmpning af lamper
3	— strømstik
4	— Ethernet-netværksstik
5-6	— stik til digitale sensorer og knapper/omskifterenheder
7	— OneWire-interfacestik (til digitale sensorer)
8	— stik til udvidelsesmodul.

Oversigt over METAFORSA-enhedens eksterne stik: Øverst på kabinettet (fig. 1) er der:

• stik (1) — Enhedsforbindelse;
• stik (2) — Tilslutning af dæmpende lamper;

At the bottom of the casing (fig. 1) there is:

• connector (3) — module power supply connection;
• connector (4) — Ethernet network connection;
• connectors (5-6) — four six-point connectors for digital sensors connection – motion, leakage, reed switch sensors, and *button/switching unit sensors;
• connector (7) — OneWire digital sensors bus connection;
• connector (8) — expansion module connection.

The physical configuration and contact point assignment of each connector are shown in table 2.

Table2

Connector	Contact	Assignment
	1-10	Load application (light lamps, thermal actuators, etc.)
	D1-4, L, N	Load application (dimming lamps)
Device status indicators		The module status indicators are described in table 3
	+24V GND	+24V — module power supply by an external 24 V power supply GND — common
	RJ45	Connector for LAN connectivity
	In1-12, In13-24 GND	Controlling devices connection (buttons, magnetic reed switches, motion or leakage sensors): +12V — sensor power output +12 V In1 … In24 — logic inputs (0-12 V) GND — common
	OneWire	Digital sensors connection (temperature) VCC — sensors power supply output +5V OW1-OW4 — OneWire data buses GND — common
	VCC GND L H	External modules connection for CAN-bus VСС — 24V output for external devices power supply GND — common L — CAN-L data bus H — CAN-H data bus

Table3

Indicator	Status	Description
Power		Power
		Power not available
Activity		Data communication
		Data communication not available
Error		No errors
		Communication error
		Module overheat
		Dimmer outputs module overload
		Absence of power on dimmers, if in configuration

System installation and assembly

Before connecting the system, you must:

• site the sensor and actuators (if not pre-installed), set the sensors and actuators;
• site the module and power supply.

Note: The module must be installed near the power supply voltage source.

CAUTION! AC power voltage must be provided to the system input through the circuit breaker assembly. It should be installed close to the power supply.

1. The power of circuit breaker assembly must comply with the load capacity;
2. Nothing else than the phase conductors can be connected to the module, the neutral wire is connected separately.

Typical diagram of METAFORSA MF-14.A module connection is shown in fig. 3.

Connection of the actuators

Connection of the lights/electric contactor/heating thermal actuator

Fig. 4

Such actuators as light, electric contactor, heating thermal actuator should be switched on any of the outputs 1 – 10, the neutral wire and the ground wire should be connected directly to the switchboard. The example of connection is shown in Fig.4.

Connection of high load device

Recomended contactors: ABB ESB series Schneider Acti 9 iCT series Hager ESC series.

Connection of single-pole water/gas supply valve

Caution: Before applying power to the load, make sure that the output configuration of METAFORSA module is correct. The incorrect configuration or incorrect connection can cause the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 5	The single pole water/gas supply valve is connected to any of the outputs of 1 – 10, the (neutral wire and the ground wire are connected directly to the switchboard. The example of connection is shown in Fig.5.

Connection of double-pole water/gas supply valve

Caution: Before applying power to the valve, it is necessary to ensure the output configuration of METAFORSA module is correct. The incorrect configuration can cause the voltage application simultaneously to both channels of the valve, which may result in the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 6	Two adjacent contact points (for example, 3, 4) are used to connect the double-pole water/gas supply valve; in these conditions the neutral wire and the ground wire are connected directly to the switchboard. The example of connection is shown in Fig.6.

Connection of single-pole gate actuator

Caution: Before applying power to the module, you should properly configure access to the application. The contacts incorrectly configured can result in the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 7	Any contact point (for example, 3) is used to connect the single-pole gate drive controllers. The example of connection is shown in Fig.7.

Connection of double-pole gate actuator

Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 8	Two adjacent contact points (for example, 3, 4) should be used to connect the double-pole gate drive controller. The example of connection is shown in Fig.8.

Connection of curtain/jalousie/shutter actuator with 220V force control

Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 9	Two adjacent contact points (for example, 3, 4) should be used to connect the curtain/jalousie/rolladens actuator, in these conditions the neutral wire and the ground wire are connected directly to the switchboard. The example of connection is shown in Fig.9.

Connection of curtain/jalousie/shutter actuator with low-voltage control

Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 10	Two adjacent contact points (for example, 3, 4) should be used to connect the curtain/jalousie/rolladens actuator with low-voltage control. The example of connection is shown in Fig.10.

Connection of sensing elements/switches/buttons

Connection of motion sensors

The motion sensors should be connected to any free input in1-in24; in these conditions their power is connected to the contact points of +12V and GND of the relevant group. The example of connection is shown in Fig.11.

Fig. 11

Connection of FW-WL.A leakage sensors

FW-WL.A leakage sensors are connected to any free input in1 – in24, in these conditions the power should be connected to +12V and GND points of the relevant group. The example of connection is shown in fig. 12.

Fig12

Fig13

Configuration and connection of the FW-WL.A sensor 1. Terminals:

+12V — sensor power is connected to the contact point of METAFORSA “+12V”;

OW — sensor pickup signal;

GND — common, connected to GND contact of METAFORSA.

2. Sensor preset switch (optionally):

1 — sensor sensitivity (ON – high, OFF – low);

2 — indicator colour setting (ON – blue, OFF – green).

3. LED status indicator.

Connection of buttons/switches/magnetic reed switches

Buttons and reed switches are connected to any free input in1-in24, while their second contact point is connected to GND point of the relevant METAFORSA module group, + 12V power outputs – not in use. The example of connection is shown in Fig. 14-15.

Fig14 connection of buttons/switching units

Fig15 connection of the magnetic reed switches (window/door position sensors)

Connection of digital sensors

The OW adapter (Fig. 16a) is supplied along with METAFORSA module with the possibility to connect up to 8 digital sensors to it. In these conditions, several devices can be connected to one channel (Fig. 16b). The connected sensors are detected automatically and do not require any original setting.

Fig16 a

Fig16 b

Configuration and connection of the OW adapter

Caution: Ensure the connection is correct. The incorrect connection may cause sensor and/or module malfunction.

Connection of auxiliary equipment.

Expansion modules include Larnitech equipment connected through the CAN-bus. Such equipment includes: dimmers, RGB-backlit control modules, multimode sensors, etc. The equipment connected to the expansion port is defined automatically and does not require any preset tuning. Connector contact pin assignment is defined in Table 4. The example of connection is shown in Fig. 17.

Caution! The 120 ohm terminating resistors should be installed at the end connectors between L and H contact points of CAN-bus. Ensure the connection is correct. The incorrect connection may cause sensor and/or module malfunction.

Module installation and connection procedure

ATTENTION! You must precisely follow the recommendations listed in the Security Requirements section hereof.

1. Install the module in the switchboard on the DIN-rail and fix it with the special latch on the module base.
2. Fasten the supply unit on the left side of the module.
3. Connect the connector (4) having the noise filter pre-installed which is supplied complete with the module.
4. Connect the connectors (5), (6).
5. Connect the connectors (1), (2).
6. Connect the connector (3).
7. Apply power to the supply unit of METAFORSA module.
8. Wait until the module is loaded, then configure it in accordance with the System Setup Instructions.
9. Apply power to the connectors (1), (2).
10. Check all equipment for proper operation.

METAFORSA module shut-off and deinstallation procedure

1. De-energize the module by disconnecting the circuit breaker assembly of the load power supply and METAFORSA module supply unit. Verify the voltage is absent on the terminals (1), (2) of the connector wires and on the input terminals of the supply unit.
2. Disconnect the load power supply connectors (1), (2).
3. Disconnect the connector (3).
4. Disconnect the connectors (4)-(6).
5. Remove the module from the DIN-rail, releasing the latch at the bottom of the module base.

Hardware setup

To configure and control METAFORSA SMART HOUSE, you must install Larnitech software on your smartphone or tablet, which is available in App Store and Play Market. After installation, follow the System Setup Instructions.

Fault diagnostics and handling

The following are some possible faults and ways of fault handling. If you have any difficulty, or face the fault undeclared here, please contact the Technical Support: [1] or [support@larnitech.com]. There are also some tips in the FAQ section at our website [2].

The actuators do not operate:

• ensure the outputs are properly configured in the application (see System Setup Instructions);
• check the connection is correct in accordance with table 2 and paragraph 3.6;
• ensure the power is supplied to the input power contact , i.e. all circuit breaker assembly are ON.
• verify the operability of the connected equipment.

The module is off, indication absent:

• check the connection to 24V supply unit as shown in table 2 (contacts pin assignment);
• check the connection of the supply unit to 220V power mains, the indicator should be ON.

Network connection fault:

• ensure the Ethernet cable is properly wired and connected to the connector;
• ensure the LED status indicators are ON on the Ethernet connector;
• check the LAN configuration is correct, Ethernet cable loops are absent;
• METAFORSA module and the device you are connecting from are in the same network.

hold integer 0-10000 1-10 by default hold is the same as runtime hold is the bridging time in miliseconds, is used for gate and jalousie, lock; Example: hold=3500

The sensors do not operate:

• ensure the inputs are properly configured in the application (System Setup Instructions);
• check the connection is correct in accordance with table 2 and paragraph 3.7;
• ensure the METAFORSA module is ON: circuit breaker assembly is closed, indication on the supply unit is ON, the module indication corresponds to the operating status – table 3;
• check the power supply availability on the sensors;
• check the integrity of lines laid to the sensors.

The auxiliary equipment does not operate:

• check the connection is correct in accordance with table 2 and paragraph 3.8-9;
• ensure the METAFORSA module is ON: circuit breaker assembly is closed, indication on the supply unit is ON, the module indication corresponds to the operating status – table 3;
• check the integrity of the CAN lines, voltage supply on the modules.

HW Settings

Name	Type, range	SUBID	Default	Description
runtime	integer 0-100	1-10	15	runtime is the open/close time in seconds, is used for jalousie, gate, valve(2 pole); Example: runtime=15
runtimeopen	integer 0-60000	Blinds subId		Runtimeopen is the open time in milliseconds, is used for blinds; Example: runtimeopen=15000
runtimeclose	integer 0-60000	Blinds subId		Runtimeclose is the close time in milliseconds, is used for blinds; Example: runtimeclose=15000
hold	integer 0-10000	1-10	500	hold is the bridging time in milliseconds, is used for gate and jalousie (by default hold is the same as runtime for jalousie and gate), lock; Example: hold=3500
def	string 'ON'	1-10	'OFF'	def is the element status is set after restart, is used for lamp, heating, valve(1 pole); Example: def='ON'
stop	Char ‘R’	1-7	–	(for 2-pole gate and blinds) If it is declared then by Stop command during the motion, the same impulse appears as it was at the beginning of the motion. Pole, an which the stop-impules is formed, is defined by the parameter Stop value. If it is ‘r’ or ‘R’ then stop-impulse is produced on the opposite to the start-impulse pole. If any other value is delcared (e.g., ‘d’ ) then the stop-impulse is on the same pole. If a Runtime passed after the beginning of the motion then the stop-impulse is not formed. Example: stop=’r’
out	char[10]	98	'LLLLHHHHP-'	Each char is responsible for the type of a particular channel 'L'-Lamp; 'M'-Lamp Inverse; 'J'-Heating NO, valve-heating, normally open; 'H'-Heating NC, valve-heating, normally closed; 'B'-Blinds (2 pole), jalousie/curtains; 'C'-Blinds Inverse (2 pole), jalousie/curtains, invert open-close; 'G'-Gate (2 pole), 2 pole gate; 'D'-Gate (2 pole) Inverse, 2 pole gate, invert open-close; 'X'-Gate (1 pole /short press), 1 pole gate; 'Z'-Gate (1 pole) Inverse, 1 pole gate, invert open-close; 'V'-Valve (2 pole), 2 pole valve; 'W'-Valve (2 pole) Inverse, 2 pole valve, invert open-close; 'R'-Valve (1 pole), 1 pole valve,; 'S'-Valve (1 pole) Inverse, 1 pole valve, invert open-close; 'K'-Lock (short press); 'N'-Lock (short press) Inverse; 'P'-Blinds (2 pole); 'O'-Blinds Inverse (2 pole), invert open-close; 'F'-FanCoil. Group1 (Lamp Toggle). For fancoil speed control; 'E'-FanCoil. Group2 (Lamp Toggle). For fancoil speed control; 'Q'-FanCoil. Group3 (Lamp Toggle). For fancoil speed control; 'U'-FanCoil. Group4 (Lamp Toggle). For fancoil speed control; 'I'-FanCoil. Group5 (Lamp Toggle). For fancoil speed control; '-'-none, nothing is connected. Example: out='LLB-G-V-W-'
dm	char[4]	98	‘LLLL’	Each char is responsible for the type of a particular channel ‘g’ – use like halogen dimer-lamp ‘s’ – Soft Switch, lamp, when on/off power is supplied/deenergised smoothly (500msec) ‘k’ – Switch, lamp, when on/off power is supplied/deenergised immediately ‘l’ – LED Function, dimmable LED lamps ‘v’ – linear Function of dimming ‘-‘ – Channel disabled ‘+’ – Regular channel Example: dm=’skl-‘
def	integer 0-250	11-14	100	The default brightness level in case of a power reset (1..250). Example: def=250
min	integer 0-100	11-14	0	Minimum dimming level, example: min=10
max	integer 0-100	11-14	100	Maximum dimming level, example max=95
start	integer 0-100	11-14	0	The Start function is used for lamps that lack the minimal voltage to get turned on. If the set value is lower than the start value, the lamp is turned on at the start value and them the light is dimmed down to the set level. Example: start=60
force	integer 0-100	11-14	10	Time duration of the starting value (measured in milliseconds). Example: force=20
runtime	integer 0-60000	11-14	1000	Runtime is the speed of changing the brightness from ‘min’ to ‘max’ (measured in milliseconds). Example: runtime=1000
offset	integer (+/- 0…39)	39-46	'0'	sensor values offset; For example, offset is -3.8 : Example: hw="offset='-3.8'"
in	char[24]	98	'BBBBBBBBBBBBMMMLLLKKKKKK'	Each char is responsible for the type of a particular channel 'B'-Button; 'C'-nButton; 'S'-Switch; 'K'-Contact; 'H'-nContact; ‘L’-Leak, Built-in floor (EW-WL) or on-the-floor (FW-WL) leakage sensor ‘N’-Third party leakage sensor; 'M'-Motion, ​motion sensor; 'V'-nMotion, motion sensor; '-'-none Example: in='MMMMMMMMMMMMLLLLLLLLLLLL' 12 motion sensors and 12 leak-sensors; in='BBBBBBBBSSSSSSBBBBSSSSSS' 12 buttons; 12 switches.

 1<item addr="339:1" auto-period="600" cfgid="40" hw="def='ON'" name="Lamp" type="lamp" uniq_id="3779"> 
 2<item addr="339:2" cfgid="40" hw="def='ON'" name="Radiator" type="valve-heating" uniq_id="3780"> 
 3    <automation name="Eco" temperature-level="16" uniq_id="3781"/> 
 4    <automation name="Comfort" temperature-level="22" uniq_id="3782"/> 
 5    <automation name="Hot" temperature-level="25" uniq_id="3783"/> 
 6</item> 
 7<item addr="339:3" cfgid="40" hw="runtime=9" name="Jalousie" sub-type="120" type="jalousie" uniq_id="32"/> 
 8<item addr="339:5" cfgid="40" hw="runtime=13" name="Gate" sub-type="120" type="gate" uniq_id="3784"/> 
 9<item addr="339:7" cfgid="40" hw="hold=4600" name="Gate" sub-type="120" type="gate" uniq_id="3785"/> 
10<item addr="339:8" cfgid="40" hw="runtime=10" name="Valve" type="valve" uniq_id="3786"/> 
11<item addr="339:11" cfgid="40" name="Motion" type="motion-sensor" uniq_id="17"/> 
12<item addr="339:12" cfgid="40" name="Motion" type="motion-sensor" uniq_id="18"/> 
13<item addr="339:13" cfgid="40" name="Motion" type="motion-sensor" uniq_id="19"/> 
14<item addr="339:16" cfgid="40" name="Leak" type="leak-sensor" uniq_id="21"/> 
15<item addr="339:17" cfgid="40" name="Leak" type="leak-sensor" uniq_id="41"/> 
16<item addr="339:19" cfgid="40" name="Switch" type="switch" uniq_id="22"/> 
17<item addr="339:20" cfgid="40" name="Switch" type="switch" uniq_id="23"/> 
18<item addr="339:21" cfgid="40" name="Switch" type="switch" uniq_id="24"/> 
19<item addr="339:22" cfgid="40" name="Switch" type="switch" uniq_id="25"/> 
20<item addr="339:23" cfgid="40" name="Door" type="door-sensor" uniq_id="26"/>
21<item addr="339:24" cfgid="40" name="Door" type="door-sensor" uniq_id="27"/> 
22<item addr="339:25" cfgid="40" name="Door" type="door-sensor" uniq_id="28"/> 
23<item addr="339:26" cfgid="40" name="Door" type="door-sensor" uniq_id="29"/> 
24<item addr="339:30" cfgid="40" name="Temperature" type="temperature-sensor" uniq_id="3772"/> 
25<item addr="339:31" cfgid="40" name="Temperature" type="temperature-sensor" uniq_id="3773"/> 
26<item addr="339:32" cfgid="40" name="Temperature" type="temperature-sensor" uniq_id="3774"/> 
27<item addr="339:33" cfgid="40" hw="offset='-10.8'" name="Temperature" type="temperature-sensor" uniq_id="3775"/> 
28<item addr="339:34" cfgid="40" hw="offset='25.1'" name="Temperature" type="temperature-sensor" uniq_id="3776"/> 
29<item addr="339:35" cfgid="40" name="Temperature" type="temperature-sensor" uniq_id="3777"/> 
30<item addr="339:36" cfgid="40" name="Temperature" type="temperature-sensor" uniq_id="3778"/> 
31<item addr="339:98" cfgid="40" hw="out='LHB-G-XV--' in='MMM--LL-BBBBKKKK'" name="Temperature" system="yes" type="temperature-sensor" uniq_id="30"/>