Metaforsa2 MF-14/sl

MF-14
Output ports Number of switched channels 10 Number of dimming channels 4 Peak load 16 A Max load per dimming channel 0.5 A (110 W at 220 V) Dimmer type MOSFET
Input ports Number of discrete inputs 24 Number of digital inputs 4
General Max CAN devices 50 Max CAN bus length 800 m (twisted pair 5 cat) Max current per CAN bus 500 mA
Other Supply voltage 11.5...27.5 V DC Dimentions 9U, 156x110x58 mm

Uvod

Priročnik za namestitev METAFORSA PAMETNE HIŠE opisuje postopek njene namestitve, montaže, delovanja in nastavitve. Pri delu s sistemom morate strogo upoštevati vse zahteve, navedene v tem priročniku. Neupoštevanje lahko povzroči poškodbe naprave, njeno odpoved, električni udar, požar in druge posledice. Proizvajalec si pridržuje pravico do sprememb tega priročnika brez predhodnega obvestila. Ta priročnik je sestavni del sistema in ostane pri končnem uporabniku.

Lastnosti

• Podpora za 10 univerzalnih izhodov:
  • Luči
  • NC/NO grelni ventili
  • Rolete
  • 1 ali 2-polna vrata
  • 1 ali 2-polni ventili
  • NC/NO ključavnice
  • Enote ventilatorskih konvektorjev
• 4 izhodi za zatemnitev
• 24 diskretnih vhodov, ki podpirajo:
  • Gumbi
  • Stikala
  • jezična stikala
  • senzorji puščanja
  • detektorji gibanja
• 4 digitalni vhodi za do 8 temperaturnih senzorjev
• Razširitvena vrata
• Releji s kontakti AgSnO2 ocenjeni za 80A 20ms zagonskega toka
• Povezava v oblak in nadzor vseh hišnih sistemov
• Glasovni nadzor (Siri, Alexa, Google Home)
• Mehanizem vtičnikov omogoča razširitev sistemskih možnosti (npr. integracija z lučmi Satel, Philips Hue, IKEA)
• Varnost pred nepooblaščenim vdorom zagotovljena s šifriranjem RSA/AES256
• Push obvestila iz sistema na vašem telefonu (prejemanje je možno tudi prek sporočil Telegram in Viber)
• Zgodovina (shranjujejo se podatki merilnika za 1 leto)
• Plug and play (možnost hitre in uporabniku prijazne razširitve sistema)
• Redne posodobitve sistema
• Velika baza skriptov, ki se nenehno posodablja, da zadovolji vse vaše potrebe
• Samodejno dnevno varnostno kopiranje prek oblaka z možnostjo obnovitve začetne konfiguracije
• Odprt API (ki omogoča integracijo Larnitecha v druge sisteme)
• Interaktiven in uporabniku prijazen spletni vmesnik LT SETUP je na voljo za napredno konfiguracijo
• Vklopi in igraj
• Je popolnoma pripravljen za namestitev sistemski komplet Smart Home

Varnostne zahteve

POZOR! Vsa dela v zvezi z montažo, priključitvijo, postavitvijo, servisom in podporo mora izvajati usposobljeno osebje z zadostnimi znanji in izkušnjami pri delu z električno opremo.

Da bi se izognili nevarnosti požara, električnega udara, poškodb sistema in/ali telesnih poškodb, je treba namestitev in sestavljanje sistema izvesti v skladu s spodaj navedenimi navodili:

• vsa priključna dela morajo biti izvedena brez električne energije;
• uporabljajte ustrezno orodje in osebno zaščito pred električnim udarom;
• ne uporabljajte poškodovanih kablov, žic in konektorjev;
• izogibajte se zlaganju kablov in žic;
• kablov in žic ne stisnite ali prepognite s prekomerno silo. V nasprotnem primeru se lahko notranji vodniki kabla in žic ogolijo ali zlomijo;
• za priklop ne uporabljajte vtičnice s slabimi kontakti;
• ne prekoračite omejitev parametrov obremenitve, navedenih v tem priročniku;
• za odsek žice napajalnih vodnikov veljajo specifikacije za omejitev gostote toka, vrsto izolacije in material žice. Svetli del lahko povzroči pregrevanje kabla in požar.

Pri delu s sistemom po napajanju NIKOLI:

• priklop/odklop konektorjev;
• odprti moduli in senzorji.

Konfiguracija in namen sistema

Namen sistema

METAFORSA PAMETNA HIŠA je že pripravljena rešitev za avtomatizacijo stanovanjskih in poslovnih prostorov, hotelskih kompleksov, ki vključuje najbolj zaželene lastnosti pametne hiše.

Naprava ima 10 krmilnih kanalov, 4 zatemnitvene kanale, 24 dohodnih senzorskih kanalov in priključek za digitalne senzorje.

Univerzalne izhode je mogoče uporabiti za krmiljenje:	Univerzalni vhodi omogočajo povezavo:
Razsvetljava	Gumbi/stikalne enote
Konektorji za vtičnice	Magnetna reed stikala
Talno ogrevanje	Senzorji gibanja
Aktivatorji zaves/vrat	Senzorji puščanja
Ventili za dovod vode/ogrevanje

Priključna vrata za digitalne senzorje

Priključna vrata za digitalne senzorje vam omogočajo priključitev različnih digitalnih senzorjev, kot so senzorji temperature, svetlobe okolice, vlažnosti in drugo.

Razširitvena vrata

Razširitveni priključek omogoča nadgradnjo sistema s priklopom pomožne opreme, kot so nadzorni modul za LED razsvetljavo, zatemnitev, merilne naprave in drugi elementi. Paket, ki je popolnoma pripravljen za namestitev, vključuje osnovno strojno in programsko opremo.

Vsebina paketa

Paket standardno vsebuje:

Glavni računalnik METAFORSA MF-14.А	1 kos
Napajalnik MEANWELL DR-15-12	1 kos
Senzor gibanja CW-MSD	3 kos
Senzor puščanja FW-WL.A	2 kos
Temperaturno občutljiv element FW-TS.A	4 kos
Magnetno reed stikalo (senzor položaja oken/vrat)	4 kos
Filter hrupa ethernetnega kabla	1 kos
Napajalni kabel	1 kos

Osnovne tehnične specifikacije sistema

Osnovne specifikacije in karakteristike modula METAFORSA MF-14.A so prikazane v tabeli 1

Table1

Specifikacija	Pomen
'Izhodna vrata
Število preklopljenih kanalov	10
Število zamenjanih skupin	10
Število kanalov za zatemnitev	4
Komutacijska napetost	0-250 V AC/DC
Konična obremenitev (en kanal)	16A
Konična obremenitev (naprava)	160A
Največja obremenitev na kanal za zatemnitev	0,5 A (110 W pri 220 V)
Vrsta zatemnitve	MOSFET
Vrsta obremenitve zatemnitve	R,C
Vrsta zatemnitve	zadnji rob
Vrsta povezave napajalnega kabla	priključek
Dovoljen odsek napajalnega kabla za priključitev v vtičnico: enožilni kabel večžilni kabel večžilni kabel s konico	0,5 … 4 mm2 0,5 … 4 mm2 0,5 … 2,5 mm2
'Vhodna vrata'
Število diskretnih vhodov	24
Število digitalnih vhodov	4
Najvišja vrednost toka na enosmernih napetostnih konektorjih	50 mA
'Drugo'
Delovna temperatura okolja	0 … +45°С
Temperatura skladiščenja/prevoza	-20 … +60°С
Dovoljena vlažnost	0 … 95 % (brez kondenzacije)
Napajanje	12 … 27,5 V DC 24 V, 0,75 A priporočeno
Maksimalno povpraševanje	0,5A
Razpoložljivi vmesniki	Ethernet, CAN, OneWire
Tip avtobusa	CAN (4-žilni)
CAN (4-žilni)	800 m* (sukani par 5 mačk)
Vrsta žice CAN	FTP Cat 5E
CAN vrsta povezave	priključek
Največja dolžina digitalne vrstice	30 m
Digitalna linija wirde tipa	UTP/FTP Cat 5E
največja dolžina LAN	100 m
Vrsta žice LAN	UTP/FTP Cat 5E
Vrsta povezave LAN	Konektor RJ-45
Dimenzijske specifikacije	9U, 156x110x58 mm
Material lupine	ABS plastika
Ohišje	IP40
vrsta vgradnje opreme	DIN-letev (EN 60715)
Teža	400 g

* – za dolge proge je potrebna namestitev dodatnih napajalnikov; največjo dolžino linije lahko zmanjšajo različni dejavniki motenj

Splošna struktura sistema

Splošni pogled modula je prikazan na Sl. 1

1	— priključek za uporabo obremenitve
2	— priključek za uporabo zatemnitvenih sijalk
3	— priključek za napajanje
4	— Omrežni priključek Ethernet
5-6	— priključki za digitalne senzorje in gumbe/stikalne enote
7	— Vmesniški konektor OneWire (za digitalne senzorje)
8	— priključek za razširitveni modul.

Pregled zunanjih priključkov naprave METAFORSA: Na vrhu ohišja (sl. 1) je:

• konektor (1) — Priključek naprav;
• konektor (2) — Priključek zatemnitvenih svetilk;

Na dnu ohišja (sl. 1) je:

• connector (3) — module power supply connection;
• connector (4) — Ethernet network connection;
• connectors (5-6) — four six-point connectors for digital sensors connection – motion, leakage, reed switch sensors, and *button/switching unit sensors;
• connector (7) — OneWire digital sensors bus connection;
• connector (8) — expansion module connection.

The physical configuration and contact point assignment of each connector are shown in table 2.

Table2

Connector	Contact	Assignment
	1-10	Load application (light lamps, thermal actuators, etc.)
	D1-4, L, N	Load application (dimming lamps)
Device status indicators		The module status indicators are described in table 3
	+24V GND	+24V — module power supply by an external 24 V power supply GND — common
	RJ45	Connector for LAN connectivity
	In1-12, In13-24 GND	Controlling devices connection (buttons, magnetic reed switches, motion or leakage sensors): +12V — sensor power output +12 V In1 … In24 — logic inputs (0-12 V) GND — common
	OneWire	Digital sensors connection (temperature) VCC — sensors power supply output +5V OW1-OW4 — OneWire data buses GND — common
	VCC GND L H	External modules connection for CAN-bus VСС — 24V output for external devices power supply GND — common L — CAN-L data bus H — CAN-H data bus

Table3

Indicator	Status	Description
Power		Power
		Power not available
Activity		Data communication
		Data communication not available
Error		No errors
		Communication error
		Module overheat
		Dimmer outputs module overload
		Absence of power on dimmers, if in configuration

System installation and assembly

Before connecting the system, you must:

• site the sensor and actuators (if not pre-installed), set the sensors and actuators;
• site the module and power supply.

Note: The module must be installed near the power supply voltage source.

CAUTION! AC power voltage must be provided to the system input through the circuit breaker assembly. It should be installed close to the power supply.

1. The power of circuit breaker assembly must comply with the load capacity;
2. Nothing else than the phase conductors can be connected to the module, the neutral wire is connected separately.

Typical diagram of METAFORSA MF-14.A module connection is shown in fig. 3.

Connection of the actuators

Connection of the lights/electric contactor/heating thermal actuator

Fig. 4

Such actuators as light, electric contactor, heating thermal actuator should be switched on any of the outputs 1 – 10, the neutral wire and the ground wire should be connected directly to the switchboard. The example of connection is shown in Fig.4.

Connection of high load device

Recomended contactors: ABB ESB series Schneider Acti 9 iCT series Hager ESC series.

Connection of single-pole water/gas supply valve

Caution: Before applying power to the load, make sure that the output configuration of METAFORSA module is correct. The incorrect configuration or incorrect connection can cause the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 5	The single pole water/gas supply valve is connected to any of the outputs of 1 – 10, the (neutral wire and the ground wire are connected directly to the switchboard. The example of connection is shown in Fig.5.

Connection of double-pole water/gas supply valve

Caution: Before applying power to the valve, it is necessary to ensure the output configuration of METAFORSA module is correct. The incorrect configuration can cause the voltage application simultaneously to both channels of the valve, which may result in the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 6	Two adjacent contact points (for example, 3, 4) are used to connect the double-pole water/gas supply valve; in these conditions the neutral wire and the ground wire are connected directly to the switchboard. The example of connection is shown in Fig.6.

Connection of single-pole gate actuator

Caution: Before applying power to the module, you should properly configure access to the application. The contacts incorrectly configured can result in the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 7	Any contact point (for example, 3) is used to connect the single-pole gate drive controllers. The example of connection is shown in Fig.7.

Connection of double-pole gate actuator

Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 8	Two adjacent contact points (for example, 3, 4) should be used to connect the double-pole gate drive controller. The example of connection is shown in Fig.8.

Connection of curtain/jalousie/shutter actuator with 220V force control

Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 9	Two adjacent contact points (for example, 3, 4) should be used to connect the curtain/jalousie/rolladens actuator, in these conditions the neutral wire and the ground wire are connected directly to the switchboard. The example of connection is shown in Fig.9.

Connection of curtain/jalousie/shutter actuator with low-voltage control

Caution: Before applying power to the module, you must properly configure the outputs in the application. The contacts configured incorrectly can lead to simultaneous power supply to both channels, resulting in the module failure and/or failure of the equipment connected to it, and even a fire.
Fig. 10	Two adjacent contact points (for example, 3, 4) should be used to connect the curtain/jalousie/rolladens actuator with low-voltage control. The example of connection is shown in Fig.10.

Connection of sensing elements/switches/buttons

Connection of motion sensors

The motion sensors should be connected to any free input in1-in24; in these conditions their power is connected to the contact points of +12V and GND of the relevant group. The example of connection is shown in Fig.11.

Fig. 11

Connection of FW-WL.A leakage sensors

FW-WL.A leakage sensors are connected to any free input in1 – in24, in these conditions the power should be connected to +12V and GND points of the relevant group. The example of connection is shown in fig. 12.

Fig12

Fig13

Configuration and connection of the FW-WL.A sensor 1. Terminals:

+12V — sensor power is connected to the contact point of METAFORSA “+12V”;

OW — sensor pickup signal;

GND — common, connected to GND contact of METAFORSA.

2. Sensor preset switch (optionally):

1 — sensor sensitivity (ON – high, OFF – low);

2 — indicator colour setting (ON – blue, OFF – green).

3. LED status indicator.

Connection of buttons/switches/magnetic reed switches

Buttons and reed switches are connected to any free input in1-in24, while their second contact point is connected to GND point of the relevant METAFORSA module group, + 12V power outputs – not in use. The example of connection is shown in Fig. 14-15.

Fig14 connection of buttons/switching units

Fig15 connection of the magnetic reed switches (window/door position sensors)

Connection of digital sensors

The OW adapter (Fig. 16a) is supplied along with METAFORSA module with the possibility to connect up to 8 digital sensors to it. In these conditions, several devices can be connected to one channel (Fig. 16b). The connected sensors are detected automatically and do not require any original setting.

Fig16 a

Fig16 b

Configuration and connection of the OW adapter

Caution: Ensure the connection is correct. The incorrect connection may cause sensor and/or module malfunction.

Connection of auxiliary equipment.

Expansion modules include Larnitech equipment connected through the CAN-bus. Such equipment includes: dimmers, RGB-backlit control modules, multimode sensors, etc. The equipment connected to the expansion port is defined automatically and does not require any preset tuning. Connector contact pin assignment is defined in Table 4. The example of connection is shown in Fig. 17.

Caution! The 120 ohm terminating resistors should be installed at the end connectors between L and H contact points of CAN-bus. Ensure the connection is correct. The incorrect connection may cause sensor and/or module malfunction.

Module installation and connection procedure

ATTENTION! You must precisely follow the recommendations listed in the Security Requirements section hereof.

1. Install the module in the switchboard on the DIN-rail and fix it with the special latch on the module base.
2. Fasten the supply unit on the left side of the module.
3. Connect the connector (4) having the noise filter pre-installed which is supplied complete with the module.
4. Connect the connectors (5), (6).
5. Connect the connectors (1), (2).
6. Connect the connector (3).
7. Apply power to the supply unit of METAFORSA module.
8. Wait until the module is loaded, then configure it in accordance with the System Setup Instructions.
9. Apply power to the connectors (1), (2).
10. Check all equipment for proper operation.

METAFORSA module shut-off and deinstallation procedure

1. De-energize the module by disconnecting the circuit breaker assembly of the load power supply and METAFORSA module supply unit. Verify the voltage is absent on the terminals (1), (2) of the connector wires and on the input terminals of the supply unit.
2. Disconnect the load power supply connectors (1), (2).
3. Disconnect the connector (3).
4. Disconnect the connectors (4)-(6).
5. Remove the module from the DIN-rail, releasing the latch at the bottom of the module base.

Hardware setup

To configure and control METAFORSA SMART HOUSE, you must install Larnitech software on your smartphone or tablet, which is available in App Store and Play Market. After installation, follow the System Setup Instructions.

Fault diagnostics and handling

The following are some possible faults and ways of fault handling. If you have any difficulty, or face the fault undeclared here, please contact the Technical Support: [1] or [support@larnitech.com]. There are also some tips in the FAQ section at our website [2].

The actuators do not operate:

• ensure the outputs are properly configured in the application (see System Setup Instructions);
• check the connection is correct in accordance with table 2 and paragraph 3.6;
• ensure the power is supplied to the input power contact , i.e. all circuit breaker assembly are ON.
• verify the operability of the connected equipment.

The module is off, indication absent:

• check the connection to 24V supply unit as shown in table 2 (contacts pin assignment);
• check the connection of the supply unit to 220V power mains, the indicator should be ON.

Network connection fault:

• ensure the Ethernet cable is properly wired and connected to the connector;
• ensure the LED status indicators are ON on the Ethernet connector;
• check the LAN configuration is correct, Ethernet cable loops are absent;
• METAFORSA module and the device you are connecting from are in the same network.

hold integer 0-10000 1-10 by default hold is the same as runtime hold is the bridging time in miliseconds, is used for gate and jalousie, lock; Example: hold=3500

The sensors do not operate:

• ensure the inputs are properly configured in the application (System Setup Instructions);
• check the connection is correct in accordance with table 2 and paragraph 3.7;
• ensure the METAFORSA module is ON: circuit breaker assembly is closed, indication on the supply unit is ON, the module indication corresponds to the operating status – table 3;
• check the power supply availability on the sensors;
• check the integrity of lines laid to the sensors.

The auxiliary equipment does not operate:

• check the connection is correct in accordance with table 2 and paragraph 3.8-9;
• ensure the METAFORSA module is ON: circuit breaker assembly is closed, indication on the supply unit is ON, the module indication corresponds to the operating status – table 3;
• check the integrity of the CAN lines, voltage supply on the modules.

HW Settings

Name	Type, range	SUBID	Default	Description
runtime	integer 0-100	1-10	15	runtime is the open/close time in seconds, is used for jalousie, gate, valve(2 pole); Example: runtime=15
runtimeopen	integer 0-60000	Blinds subId		Runtimeopen is the open time in milliseconds, is used for blinds; Example: runtimeopen=15000
runtimeclose	integer 0-60000	Blinds subId		Runtimeclose is the close time in milliseconds, is used for blinds; Example: runtimeclose=15000
hold	integer 0-10000	1-10	500	hold is the bridging time in milliseconds, is used for gate and jalousie (by default hold is the same as runtime for jalousie and gate), lock; Example: hold=3500
def	string 'ON'	1-10	'OFF'	def is the element status is set after restart, is used for lamp, heating, valve(1 pole); Example: def='ON'
stop	Char ‘R’	1-7	–	(for 2-pole gate and blinds) If it is declared then by Stop command during the motion, the same impulse appears as it was at the beginning of the motion. Pole, an which the stop-impules is formed, is defined by the parameter Stop value. If it is ‘r’ or ‘R’ then stop-impulse is produced on the opposite to the start-impulse pole. If any other value is delcared (e.g., ‘d’ ) then the stop-impulse is on the same pole. If a Runtime passed after the beginning of the motion then the stop-impulse is not formed. Example: stop=’r’
out	char[10]	98	'LLLLHHHHP-'	Each char is responsible for the type of a particular channel 'L'-Lamp; 'M'-Lamp Inverse; 'J'-Heating NO, valve-heating, normally open; 'H'-Heating NC, valve-heating, normally closed; 'B'-Blinds (2 pole), jalousie/curtains; 'C'-Blinds Inverse (2 pole), jalousie/curtains, invert open-close; 'G'-Gate (2 pole), 2 pole gate; 'D'-Gate (2 pole) Inverse, 2 pole gate, invert open-close; 'X'-Gate (1 pole /short press), 1 pole gate; 'Z'-Gate (1 pole) Inverse, 1 pole gate, invert open-close; 'V'-Valve (2 pole), 2 pole valve; 'W'-Valve (2 pole) Inverse, 2 pole valve, invert open-close; 'R'-Valve (1 pole), 1 pole valve,; 'S'-Valve (1 pole) Inverse, 1 pole valve, invert open-close; 'K'-Lock (short press); 'N'-Lock (short press) Inverse; 'P'-Blinds (2 pole); 'O'-Blinds Inverse (2 pole), invert open-close; 'F'-FanCoil. Group1 (Lamp Toggle). For fancoil speed control; 'E'-FanCoil. Group2 (Lamp Toggle). For fancoil speed control; 'Q'-FanCoil. Group3 (Lamp Toggle). For fancoil speed control; 'U'-FanCoil. Group4 (Lamp Toggle). For fancoil speed control; 'I'-FanCoil. Group5 (Lamp Toggle). For fancoil speed control; '-'-none, nothing is connected. Example: out='LLB-G-V-W-'
dm	char[4]	98	‘LLLL’	Each char is responsible for the type of a particular channel ‘g’ – use like halogen dimer-lamp ‘s’ – Soft Switch, lamp, when on/off power is supplied/deenergised smoothly (500msec) ‘k’ – Switch, lamp, when on/off power is supplied/deenergised immediately ‘l’ – LED Function, dimmable LED lamps ‘v’ – linear Function of dimming ‘-‘ – Channel disabled ‘+’ – Regular channel Example: dm=’skl-‘
def	integer 0-250	11-14	100	The default brightness level in case of a power reset (1..250). Example: def=250
min	integer 0-100	11-14	0	Minimum dimming level, example: min=10
max	integer 0-100	11-14	100	Maximum dimming level, example max=95
start	integer 0-100	11-14	0	The Start function is used for lamps that lack the minimal voltage to get turned on. If the set value is lower than the start value, the lamp is turned on at the start value and them the light is dimmed down to the set level. Example: start=60
force	integer 0-100	11-14	10	Time duration of the starting value (measured in milliseconds). Example: force=20
runtime	integer 0-60000	11-14	1000	Runtime is the speed of changing the brightness from ‘min’ to ‘max’ (measured in milliseconds). Example: runtime=1000
offset	integer (+/- 0…39)	39-46	'0'	sensor values offset; For example, offset is -3.8 : Example: hw="offset='-3.8'"
in	char[24]	98	'BBBBBBBBBBBBMMMLLLKKKKKK'	Each char is responsible for the type of a particular channel 'B'-Button; 'C'-nButton; 'S'-Switch; 'K'-Contact; 'H'-nContact; ‘L’-Leak, Built-in floor (EW-WL) or on-the-floor (FW-WL) leakage sensor ‘N’-Third party leakage sensor; 'M'-Motion, ​motion sensor; 'V'-nMotion, motion sensor; '-'-none Example: in='MMMMMMMMMMMMLLLLLLLLLLLL' 12 motion sensors and 12 leak-sensors; in='BBBBBBBBSSSSSSBBBBSSSSSS' 12 buttons; 12 switches.

 1<item addr="339:1" auto-period="600" cfgid="40" hw="def='ON'" name="Lamp" type="lamp" uniq_id="3779"> 
 2<item addr="339:2" cfgid="40" hw="def='ON'" name="Radiator" type="valve-heating" uniq_id="3780"> 
 3    <automation name="Eco" temperature-level="16" uniq_id="3781"/> 
 4    <automation name="Comfort" temperature-level="22" uniq_id="3782"/> 
 5    <automation name="Hot" temperature-level="25" uniq_id="3783"/> 
 6</item> 
 7<item addr="339:3" cfgid="40" hw="runtime=9" name="Jalousie" sub-type="120" type="jalousie" uniq_id="32"/> 
 8<item addr="339:5" cfgid="40" hw="runtime=13" name="Gate" sub-type="120" type="gate" uniq_id="3784"/> 
 9<item addr="339:7" cfgid="40" hw="hold=4600" name="Gate" sub-type="120" type="gate" uniq_id="3785"/> 
10<item addr="339:8" cfgid="40" hw="runtime=10" name="Valve" type="valve" uniq_id="3786"/> 
11<item addr="339:11" cfgid="40" name="Motion" type="motion-sensor" uniq_id="17"/> 
12<item addr="339:12" cfgid="40" name="Motion" type="motion-sensor" uniq_id="18"/> 
13<item addr="339:13" cfgid="40" name="Motion" type="motion-sensor" uniq_id="19"/> 
14<item addr="339:16" cfgid="40" name="Leak" type="leak-sensor" uniq_id="21"/> 
15<item addr="339:17" cfgid="40" name="Leak" type="leak-sensor" uniq_id="41"/> 
16<item addr="339:19" cfgid="40" name="Switch" type="switch" uniq_id="22"/> 
17<item addr="339:20" cfgid="40" name="Switch" type="switch" uniq_id="23"/> 
18<item addr="339:21" cfgid="40" name="Switch" type="switch" uniq_id="24"/> 
19<item addr="339:22" cfgid="40" name="Switch" type="switch" uniq_id="25"/> 
20<item addr="339:23" cfgid="40" name="Door" type="door-sensor" uniq_id="26"/>
21<item addr="339:24" cfgid="40" name="Door" type="door-sensor" uniq_id="27"/> 
22<item addr="339:25" cfgid="40" name="Door" type="door-sensor" uniq_id="28"/> 
23<item addr="339:26" cfgid="40" name="Door" type="door-sensor" uniq_id="29"/> 
24<item addr="339:30" cfgid="40" name="Temperature" type="temperature-sensor" uniq_id="3772"/> 
25<item addr="339:31" cfgid="40" name="Temperature" type="temperature-sensor" uniq_id="3773"/> 
26<item addr="339:32" cfgid="40" name="Temperature" type="temperature-sensor" uniq_id="3774"/> 
27<item addr="339:33" cfgid="40" hw="offset='-10.8'" name="Temperature" type="temperature-sensor" uniq_id="3775"/> 
28<item addr="339:34" cfgid="40" hw="offset='25.1'" name="Temperature" type="temperature-sensor" uniq_id="3776"/> 
29<item addr="339:35" cfgid="40" name="Temperature" type="temperature-sensor" uniq_id="3777"/> 
30<item addr="339:36" cfgid="40" name="Temperature" type="temperature-sensor" uniq_id="3778"/> 
31<item addr="339:98" cfgid="40" hw="out='LHB-G-XV--' in='MMM--LL-BBBBKKKK'" name="Temperature" system="yes" type="temperature-sensor" uniq_id="30"/>